Table of Contents
Advertisement
Quick Links
3" GASOLINE CHIPPER/SHREDDER
02/2017
MODEL: KCG-300CS
INSTRUCTION MANUAL
Read this manual. Do not attempt to operate the chipper/shredder until you have read and understood the
safety, operation, and maintenance instructions in this manual.
COPYRIGHT © 2016 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
Advertisement
Table of Contents
Summary of Contents for King Canada Power force KCG-300CS
- Page 1 MODEL: KCG-300CS INSTRUCTION MANUAL Read this manual. Do not attempt to operate the chipper/shredder until you have read and understood the safety, operation, and maintenance instructions in this manual. COPYRIGHT © 2016 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
-
Page 2: Warranty And Service Information
Shipping and handling charges may apply. If a defect is found, KING CANADA will either repair or replace the product. PARTS DIAGRAM & PARTS LISTS Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list. KING CANADA TOOLS INC. DORVAL, qUEBEC, CANADA H9P 2Y4... - Page 3 BASIC & SPECIFIC SAFETY PRECAUTIONS FOR GAS ENGINES BASIC SAFETY INFORMATION INADEqUATE VENTILATION ExHAUST FUMES ARE DANGEROUS Materials placed against or near the engine or operating in areas •Never operate the engine in a closed area or it may cause where the temperature exceeds 40° C ambient (such as storage rooms unconsciensness and death within a short time.
- Page 4 BASIC & SPECIFIC SAFETY PRECAUTIONS Basic & Specific safety Precautions Safe Handling of Gasoline Powered Equipment: 1. Do not put hands and feet near rotating parts or in the feeding To avoid personal injury or property damage use extreme care in chambers and discharge opening. Contact with the rotating impeller handling gasoline.
-
Page 5: Specifications
GETTING TO KNOw YOUR 3” CHIPPER SHREDDER 1. Hopper. Place leaves, twigs and branches up to 1/2” in diameter for shredding. 2. Chipper chute. Place branches up to 3” in diameter for chipping. 3. Chute deflector. All shredded or chipped material will come out of the chute deflector, it is recommended to install the collection bag to the chute deflector. - Page 6 ASSEMBLY& INITIAL SET-UP BEFORE OPERATION ASSEMBLY Chute Deflector 1. Install the chute deflector (A) Fig.1 to the impeller housing using 2 hex. bolts and washers (B). Chipper Chute 1. Install the chipper chute base (C) Fig.1 to the impeller housing using 3 washers and nylon hex.
- Page 7 INITIAL SET-UP BEFORE OPERATION & STARTING ENGINE INITIAL SETUP BEFORE OPERATION ENGINE FUEL LEVEL wARNING! The engine comes with no fuel in the fuel tank. Make sure there is enough fuel in the fuel tank before operating. 1. If it is necessary to add fuel, first make sure the engine switch is OFF, then open the fuel cap (A) Fig.5 by turning it counterclockwise.
-
Page 8: Operation
OPERATION OPERATION wARNING: The operation of any chipper shredder can result in foreign objects being thrown into the eyes, which can damage your eyes severely. Always wear the safety glasses or eye shields before chipping or shredding and while performing any adjustments or repairs. Shredding Yard waste such as leaves and pine needles can be placed in the hopper (A) Fig.9 for shredding. -
Page 9: Storage And Maintenance
STORAGE & MAINTENANCE Storage ALWAYS shut off the engine before cleaning, adjusting, or repairing the chipper shredder or its engine. Follow the instructions below for storing your chipper/shredder between uses. 1. Unlock and pivot the chipper chute backwards to minimize the space needed for storage. 2. - Page 10 STORAGE & MAINTENANCE Blade Care- Shredder Blade wARNING: The shredder blade is sharp. Wear leather work gloves to protect your hands. 1. Stop engine, disconnect spark plug, and make sure that all moving parts have come to a complete stop. 2.
-
Page 11: Maintenance
MAINTENANCE Maintaining your engine Engine Oil Replacement Oil crankcase capacity: 0.6 litres. Engine oil should be replaced after the first 20 hours of operation or after the first month of use, it should be replaced every 100 hours or 6 months after. To replace engine oil;...