Verizon CDM8950 User Manual page 34

RESTRICTIONS
Use the following procedure to configure Location Setting, Calls and Messages
restrictions.
1. From standby mode, press the OK Key
[MENU], the Directional
Key right twice for SETTINGS & TOOLS, and press 6. Phone
Settings, 6. Security.
2. Enter the four-digit Lock Code, then press the OK Key
[OK].
The default Lock Code is "0000".
3. Press
"2. Restrictions".
4. Enter the four-digit Lock Code again, then press the OK Key
[OK].
5. Select one of the following settings:
• Location Setting: Unlock Setting/Lock Setting.
• Calls: Incoming Calls/Outgoing Calls
For Incoming Calls, set Allow All/Contacts Only/Block All.
For Outgoing Calls, set Allow All/Contacts Only/Block All.
• Messages: Incoming Messages/Outgoing Messages
For Incoming Messages, set Allow All/Block All.
For Outgoing Messages, set Allow All/Block All.
• Dial-Up Modem: Allow/Block.
Chapter 4 − Menu Function
66
PHONE LOCK SETTING
This setting specifies whether the phone should be locked whenever it is turned on.
Lock Mode prevents the unauthorized use of your phone. Once the phone is locked, it
is in restricted mode until the Lock Code is entered. You can still make emergency calls.
You can modify the Lock Code using the new Lock code within the Security menu.
1. From standby mode, press the OK Key
[MENU], the Directional
Key right twice for SETTINGS & TOOLS, and press 6. Phone
Settings, 6. Security.
2. Enter the four-digit Lock Code, then press the OK Key
[OK].
The default lock code is the last 4 digits of your Mobile Telephone
Number.
3. Press
"3. Phone Lock Setting".
4. Press the Directional Key
up or down to select one of the
following settings, then press the OK Key [OK].
• Unlocked: Phone is unlocked.
• On Power Up: Phone will lock when it is turned on.
LOCK PHONE NOW
Lock the phone now.
1. From standby mode, press the OK Key
[MENU], the Directional
Key right twice for SETTINGS & TOOLS, and press 6. Phone
Settings, 6. Security.
2. Enter the four-digit Lock Code, then press the OK Key
[OK].
The default Lock Code is the last 4 digits of your mobile telephone
number.
3. Press
"4. Lock Phone Now".
4. To unlock the phone, in stanby mode, press the Right Soft Key
[Unlock] and enter the four-digit Lock Code, then press the OK
Key [OK].
RESTORE PHONE
To delete all User Data and restore all settings to their initial defaults:
1. From standby mode, press the OK Key
[MENU], the Directional
Key right twice for SETTINGS & TOOLS, and press 6. Phone
Settings, 6. Security.
2. Enter the four-digit Lock Code, then press the OK Key
[OK].
3. Press
"5. Restore Phone".
4. After reading the warning message that appears, press the
Directional Key up or down to select "Yes", and then press the
OK Key [OK].
5. After reading the message that appears, press the OK Key
[OK].
6. Enter the four-digit Lock Code, then press the OK Key
[OK].
The phone will turn off and then back on again automatically.
SYSTEM SELECT
You can set your phone to search or roam on another network when you are not in
your home area. Leave this setting as default unless you want to alter the system
selection as instructed by your service provider.
1. From standby mode, press the OK Key
[MENU], the Directional
Key right twice for SETTINGS & TOOLS, and press 6. Phone
Settings, 7. System Select.
2. Press the Directional Key
up or down to select one of the
following settings, then press the OK Key [OK].
• Automatic B: Scan radio channels based on the Automatic B setting.
• Automatic A: Scan radio channels based on the Automatic A setting.
• Home Only: Only within your home area or home affiliated area.
Menu Function − Chapter 4
67