Page 1
GENERAL INFORMATION 0000-00 GENERAL INFORMATION GENERAL INFORMATION 1. HOW TO READ ELECTRICAL WIRING DIAGRAM..........2. ELECTRICAL SYSTEM LAY-OUT..
Page 3
- Internal circuit of component (Switch) (Component Name, Terminal Number and Connecting Wiring Circuit) - Lower horizontal line : Ground line ·Ground position (G101 ~ G402) ·B : Body Ground ·Refer to Major Ground Position (Section2) GENERAL INFORMATION ACTYON 2006.03...
Page 4
Battery Voltage (B+) supply in Ignition Switch “ON” and “ACC” Battery Voltage (B+) supply directly regardless of Ignition Switch Ground connected to battery (-) Battery Voltage (B+) supply in Head Lamp Switch 1st and 2nd step (Illumination circuit) GENERAL INFORMATION ACTYON 2006.03...
Page 5
Underbody In the locating section, the assignment for part number startsfrom left bottom and proceeds clockwise. In the fuse and relay box or the instrument panel, the partnumber is assigned from left top to light bottom. GENERAL INFORMATION ACTYON 2006.03...
Page 6
0000-00 2. ELECTRICAL SYSTEM LAY-OUT 1) POSITION OF INTERIOR UNIT & SENSOR GENERAL INFORMATION ACTYON 2006.03...
Page 7
0000-00 2) ENGINE ROOM SWITCH / UNIT & SENSOR GENERAL INFORMATION ACTYON 2006.03...
Page 8
0000-00 3) INTERIOR SWITCH GENERAL INFORMATION ACTYON 2006.03...
Page 9
0000-00 4) AIR-BAG SYSTEM GENERAL INFORMATION ACTYON 2006.03...
Page 10
0-10 0000-00 5) AIR-CONDITIONING SYSTEM GENERAL INFORMATION ACTYON 2006.03...
2820-01 PREHEATING CIRCUIT 2820-01 1) CONNECTOR INFORMATION 2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
Page 58
Check each glow plug for short in circuit Check each glow plug for open in circuit due to overvoltage Check glow plug for short to ground ▶ FORCEFUL RELAY SHUT-DOWN When glow plug is shorted to ground CIRCUIT ACTYON 2006.03...
1491-01 ECU (ENGINE CONTROL UNIT - D20DT) 1491-01 ENG MAIN RELAY, PEDAL MODULE, HFM SENSOR, VALVE, (1) CONNECTOR INFORMATION CRUISE CONTROL SW (2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
Page 60
1491-01 2) FUEL FILTER WARNING LAMP, IMMOBILIZER, SENSOR (1) CONNECTOR INFORMATION CIRCUIT (FUEL PRESSURE, SHAFT, BOOSTER PRESSURE, CRANK SHAFT, KNOCK, COOLANT TEMP., FUEL TEMP.) (2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
Page 61
1491-01 3) INJECTOR, CAN LINE (1) CONNECTOR INFORMATION (2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
Page 62
ECU to generate necessary current during injector drive stages. Current control circuit divides current applying time (injection time) into full-in-current-phase and hold-current-phase and then the injectors should work very correctly under every working condition. CIRCUIT ACTYON 2006.03...
0-14 3110-01 3110-01 1) CONNECTOR INFORMATION 2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
Page 68
Solenoid 6: S6 is a normally open ON/OFF solenoid that sets the high/low level of line pressure. Solenoid OFF gives high pressure. Solenoid 7: S7 is a normally open ON/OFF solenoid that controls the application of the converter clutch. Solenoid ON activates the clutch. CIRCUIT ACTYON 2006.03...
Page 69
Output circuits which control external devices such as the Variable Pressure Solenoid precautions should be observed, for example when arc welding or jump starting. (VPS) driver, On/Off solenoid drivers, a diagnostics output and the driving mode indicator light. CIRCUIT ACTYON 2006.03...
Page 70
This results in maximum oil flow through the external oil cooler and eliminates slippage in torque converter. Both these actions combine to reduce the oil temperature in the transmission. CIRCUIT ACTYON 2006.03...
Page 71
Inhibit starting of the vehicle when the shift lever is in a position other than Park or Neutral Illuminate the reverse lamps when Reverse is selected Indicate to the TCM which lever position has been selected by way of a varying resistance. Readings for Resistance / Shift Lever Positions CIRCUIT ACTYON 2006.03...
0-25 3410-01 TCCU 3410-01 1) CONNECTOR INFORMATION 2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
Page 79
Change the transfer case wiring connector from No.4 pin to No.1 pin. (Power and ground related to the speed sensor) The new TCCU is available to install on the vehicle with the conventional DI engine part time TCCU. ▶ SPECIFICATIONS CIRCUIT ACTYON 2006.03...
Page 80
Shift conditions are as follows: Normal battery voltage and shift motor for all gears 2H and 4H shifts has nothing to do with the vehicle speed, the “N” position in the automatic transmission or the clutch signal. CIRCUIT ACTYON 2006.03...
Page 81
The motor stops when the encoder related troubles are detected during shift operation. wires and connectors for looseness It moves toward LOW-HIGH direction for 5 seconds so that the motor is not left in unrecognized position. and open circuit. CIRCUIT ACTYON 2006.03...
0-30 4892-01 ABS/ESP 4892-01 W/SPEED SENSOR, STOP LAMP SW, DIAGNOSIS, WARNING LAMP (ABS/ESP) (1) CONNECTOR INFORMATION (2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
Page 84
0-31 4892-01 PRESSURE SENSOR, S.W.A SENSOR, SENSOR CLUSTER, ESP OFF SW, HDC (1) CONNECTOR INFORMATION (2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
Page 85
In this case, HECU sounds an abnormal noise and brake pedal may be very rigid, but The HBA System increases the braking force under urgent situations to enhance the inputted this is a normal condition due to HDC operation. braking force from the driver. CIRCUIT ACTYON 2006.03...
Page 86
This system is developed to help the driver avoid the danger of losing the control of the vehicle stability due to under-steering or over-steering during cornering. CIRCUIT ACTYON 2006.03...
Page 87
Even when the ESP is operated for a very short period of time, the ESP warning lamp blinks minimum of 4 times every 175 milliseconds and the buzzer sounds for at least 1.4 seconds with 100 ms interval. CIRCUIT ACTYON 2006.03...
0-35 8810-01 AIR-BAG (CURTAIN AIR-BAG) 8810-01 1) CONNECTOR INFORMATION 2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
Page 89
Please do not connect a tester to any air bag connector or single item to measure the supplied power or resistance. The detonator may explode due to a sudden extra power supplied by the tester. Before removing or installing any air bag related components, disconnect the negative battery cable. CIRCUIT ACTYON 2006.03...
Page 90
When the Air Bag Unit Receives Any Malfunction Signals from the Other Systems When, due to an error from outside the system, the intermittent failure signal is received 5 times or less, the air bag warning lamp comes on for about 6 seconds and then, goes off. CIRCUIT ACTYON 2006.03...
Page 95
The HDC switch is a push & self return type switch - when you press it once, it starts to · HDC system error occurs operate and when you press it again, it stops the operation. Brake system overheat · CIRCUIT ACTYON 2006.03...
0-44 7410-02 POWER SEAT - PASSENGER 7410-02 1) CONNECTOR INFORMATION 2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
0-45 8510-52 8510-52 ELECTRIC OUTSIDE MIRROR & FOLDING 1) CONNECTOR INFORMATION 2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
0-47 8710-02 STICS 8710-02 (1) CONNECTOR INFORMATION 1) POWER/GROUND, CHIME BELL, BUZZER WARNING LAMP (BRAKE, SEAT BELT, DR OPEN) (2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
Page 101
0-48 8710-02 2) CENTRAL DOOR LOCK CIRCUIT (1) CONNECTOR INFORMATION (2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
Page 102
0-49 8710-02 3) TAIL LAMP, HAZARD, POWER WINDOW (1) CONNECTOR INFORMATION (2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
Page 103
0-50 8710-02 4) DEFOGGER (1) CONNECTOR INFORMATION (2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
Page 104
0-51 8710-02 5) PANIC, AUTO LIGHT & RAIN SENSING, ROOM LAMP (1) CONNECTOR INFORMATION (2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
Page 105
0-52 8710-02 6) FRT WIPER/WASHER & RR WASHER (1) CONNECTOR INFORMATION (2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
Page 106
Receiving distance: Approx. 10 ~ 15 m (In case there are not obstacles around the It cannot be activated while the front washer switch or the auto washer and wiper system)em) (AFW: Advanced Fast Washer) is in operation. CIRCUIT ACTYON 2006.03...
Page 107
The auto washer switch input is overridden during the rain sensor coupled wiper or vehicle speed sensitive INT wiper operation. When the auto INT switch input is received during the auto washer operation, the auto washer operation stops and the auto INT operation is activated. CIRCUIT ACTYON 2006.03...
Page 108
2 seconds, then continuously outputs the small amount of rain drops. Therefore, change the knob to the low sensitivity. parking signal of current sensitivity. The wiper motor runs only when the rain sensor requires. · CIRCUIT ACTYON 2006.03...
Page 109
If the key is in the key cylinder, the ignition key reminder the INT switch positioned to “ON”. function is activated. · Intermittent interval (at 0 km/h): 3 ± 0.5 ~ 19 ± 2 seconds This function does not work if the vehicle speed is over 10 km/h. CIRCUIT ACTYON 2006.03...
Page 110
The luggage room lamp comes on when opening the tailgate while the tailgate coupled luggage room lamp switch is pressed. CIRCUIT ACTYON 2006.03...
Page 111
10 minutes after completion of output for 12 minutes. This can be done The door unlock relay output is “ON” for 0.5 seconds when receiving the only once. remote control unlock signal. The output is “OFF” when the IGN 2 switch is “OFF”. CIRCUIT ACTYON 2006.03...
Page 112
“ON” position. · If the ignition switch is turned to ON position when the warning is activated in armed mode, the warning is canceled immediately and the warning buzzer stops after 27 seconds (remaining time). CIRCUIT ACTYON 2006.03...
Page 113
It the door is not opened within 30 seconds after unlocking the door with remote control control key sends the coded control message to the CPU in receiver to control the vehicle. key, the system outputs “LOCK” signal and activates the armed mode (Relock function). CIRCUIT ACTYON 2006.03...
Page 114
0-61 7830-03 F. DIAGNOSIS TROUBLE CODE AND HELP TIPS CIRCUIT ACTYON 2006.03...
0-63 8510-05 POWER WINDOW CIRCUIT 8510-05 1) CONNECTOR INFORMATION 2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
Page 117
30 seconds (T2) just for once when opening the door during its extended operation period of 30 seconds (T1). The power window relay is turned “OFF” when closing the door during its extended operation period of 30 seconds (T2). CIRCUIT ACTYON 2006.03...
0-66 7632-16 7632-16 CIGAR LIGHTER & POWER OUTLET CIRCUIT 1) CONNECTOR INFORMATION 2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
However, if the force against the sunroof is less than the specified value, the Anti-Trap power supply system is in normal conditions, check if the ground circuit of switch is function doesn't operate. securely tightened and reset the sunroof system again. CIRCUIT ACTYON 2006.03...
Page 122
0-69 7340-03 E. TROUBLE DIAGNOSIS CIRCUIT ACTYON 2006.03...
Page 123
0-70 8310-01 HEAD LAMP & DRL HEAD LAMP & DRL 1) CONNECTOR INFORMATION 8310-01 (DAY TIME RUNNING LIGHT) UNIT CIRCUIT 2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
Page 124
0-71 8510-00 8510-00 HLLD (HEAD LAMP LEVEL’G DEVICE) CIRCUIT 1) CONNECTOR INFORMATION 2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
0-73 8410-01 8410-01 TURN SIGNAL & HAZARD LAMP CIRCUIT 1) CONNECTOR INFORMATION 2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
0-78 7770-10 AUTO DIMMING ROOM MIRROR CIRCUIT 7770-10 1) CONNECTOR INFORMATION 2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
0-80 8790-01 PARKING AID CIRCUIT 8790-01 1) CONNECTOR INFORMATION 2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
Page 134
Frequency: 40 KHz ± 2 KHz Detecting range (13.5 V) · Horizontal: Min. 20° at 110 ± 5 cm Min. 100° at 50 ± 5 cm · Vertical: Min. 20° at 110 ± 5 cm Min. 60° at 50 ± 5 cm CIRCUIT ACTYON 2006.03...
Page 135
When the sensing portion is covered by rain, water drops, snow or mud. (operates normally after cleaned) When receiving other ultrasonic signals (metal sound or air braking noises from heavy commercial vehicles). When a high-power radio is turned on. CIRCUIT ACTYON 2006.03...
0-83 8790-01 PTC HEATER 6810-15 (POSITIVE TEMPERATURE COEFFICIENT) 1) CONNECTOR INFORMATION 2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
Page 137
60°C and ambient temperature ≤ 0°C ~ 5°C, PTC operates (ON) ▶ PTC “OFF” CONDITION Airconditioner blower switch OFF Ambient temperature sensor error (wiring short or open) When engine craking Battery voltage is lower than 11V When preheating the engine (Glow indicator “ON”) CIRCUIT ACTYON 2006.03...
0-85 6910-01 FFH (FUEL FIRED HEATER) 6910-01 1) CONNECTOR INFORMATION 2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
Page 139
It is possible to diagnose the system by connecting the diagnostic device to controller. For details, refer to the “Diagnosis Procedures” section. Emergency shutdown If an emergency shutdown -EMERGENCY OFF- is necessary during operation, proceed as follows; Pull the fuse (Ef6: 20A) out. Disconnect the heater from the battery. CIRCUIT ACTYON 2006.03...
0-89 6810-20 FATC (FULL AUTO TEMP. CONTROL) CIRCUIT 6810-20 1) CONDENSOR FAN, AIR MIX MOTOR, SUN SENSOR, WATER (1) CONNECTOR INFORMATION TEMP SENSOR (2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
Page 143
0-90 6810-20 2) BLOWER, ACTUATOR (MODE, INTAKE), AQS SENSOR (1) CONNECTOR INFORMATION (2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
Page 144
Phenomenon when air conditioner system is defective During abrupt acceleration for the vehicle equipped with manual transmission (Initial automatic diagnosis) If any sensor in the air conditioner system is defective, the temperature display blinks about 3 timesduring initial operation of air conditioner controller. CIRCUIT ACTYON 2006.03...
Page 145
However, if the voltage is not changed, replace thehumidity sensor. In addition, if the output voltage is extremely high or low even in the specified range, replace the humidity sensor. CIRCUIT ACTYON 2006.03...
Page 146
Measure the voltage to the sun sensor from FATC connector. (approx. 2.5 V under sunlight and 4.8 Vunder shade.) If the voltage value cannot be measured, check the circuit for open. If the measured value is within thespecified range, replace the FATC controller. CIRCUIT ACTYON 2006.03...
Page 147
Andmeasure the voltage between terminal A12 and A11 on the FATC controller connector. (standard: approx.12 V) If the voltage value cannot be measured, check the circuit for open. If the measured value is within thespecified range, replace the FATC controller. CIRCUIT ACTYON 2006.03...
0-95 6810-20 AIR-CON (MANUAL) CIRCUIT 6810-20 (1) CONNECTOR INFORMATION 1) COMPRESSOR, MOTOR (MODE, INTAKE, AIR MIX) (2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
Page 149
0-96 6810-20 2) BLOWER (1) CONNECTOR INFORMATION (2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION CIRCUIT ACTYON 2006.03...
Need help?
Do you have a question about the Actyon 2006 and is the answer not in the manual?
Questions and answers