Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ford FPXD30E
Summary of Contents for Ford FPXD30E
- Page 1 MODEL#: FPXD30E FPXD40E FPXD30H Diesel Water Pump OPERATOR’S MANUAL...
-
Page 2: Table Of Contents
TABLE OF CONTENTS INFORMATION Introduction ..........................3 Safety Rules ..........................4 Safety Symbols ......................... 4 Safety Instructions ......................4 Water Pump Features ......................... 7 Assembly ..........................8 Packing List ........................8 Unpacking ........................8 Suction Hose Installation . -
Page 3: Information Introduction
INTRODUCTION FPXD30E FPXD40E FPXD30H 178FA 186FA 192FA 92mm×75mm 78mm×64mm 86mm×72mm Vertical Cylinder, 4 Stroke,Air Cooled 8.2kW/3600 rpm 4.0kW/3600 rpm 6.3kW/3600 rpm 26.8N.m 20.3N.m 13.2N.m 20:1 19:1 19:1 80(3 inch) 100(4 inch) 80(3 inch) 100(4 inch) Discharge Capacity (m³/h) ≤85dB(A) 7m ≤85dB(A) 7m... -
Page 4: Safety Rules
SAFETY RULES Safety Symbols Indicates a potentially hazardous situation which could result in serious injury or death if not WARNING! avoided. CAUTION! Indicates a potentially hazardous situation which could result in damage to equipment or property. Risk of explosion Hot surface Risk of fire Safety Instructions Most accidents can be prevented by following the instructions in this manual. - Page 5 • Keep pump at least 3 feet (1 meter) away from equipment , outlets, or buildings. Never operate this unit if there are any broken or missing parts and only use Ford WARNING! Equipment replacement parts specifically designed for this unit.
- Page 6 SAFETY RULES SAFETY (USE CD 15W40) Fill engine with exact amount of oil supplied with this unit. Always check oil level before starting Read Operator’s Manual before Using...
-
Page 7: Water Pump Features
WATER PUMP FEATURES FUEL FILL CAP MUFFLER FRAME AIR FILTER DISCHARGE PORT FUEL SWITCH ENGINE ON/OFF SWITCH OIL FILLER CAP/DIPSTICK OIL FILTER OIL DRAIN PLUG PRIMING WATER FILLER CAP STRAINER SUCTION PORT PUMP DRAIN CAP... -
Page 8: Assembly
Do not operate this pump if any of the parts are damaged or missing until the part WARNING! Minimum hose size:FPXD40E=4in.(100mm) Minimum hose size:FPXD30E=3in.(80mm) At the pump’s Suction Port connect the gasket, hose barb fitting,hose wing nut,hose clamp,and suction hose as... -
Page 9: Discharge Hose Installation
ASSEMBLY Minimum hose size:FPXD40E=4in.(100mm) Minimum hose size:FPXD30E=3in.(80mm) HOSE CONNECTOR HOSE CLAMP DISCHARGE HOSE Carefully add 1100ml of 4-Cycle engine Oil (SAE CD 10W-40) to empty reservoir until oil reaches the outer edge of CAUTION! Insert a funnel into the fuel tank and carefully pour fresh, diese,the tank until fuel level reaches 1/2 inches below the top of the neck. -
Page 10: Operation
WARNING! Improper use of this pump could result in serious injury or death. Know how to stop this pump quickly in case of an emergency. Never leave the pump running while unattended to for any reason. Keep children and pets away from the pump when it is running. Pre-Operation Check List WARNING! Priming the Trash Pump (See FIG 5) - Page 11 OPERATION Placing the Trash Pump (See FIG 6) To maximize the pump’s power, the pump should be placed as close to the water level as possible and the hose should be as short as possible. • As hose length increases, pump output decreases. •...
-
Page 12: How To Start Water Pump
OPERATION Starting Water pump (See FIG 8A-8E) • Place water pump on a level surface near the water level. Keep the pump at least 3 feet away from walls or equipment. • Prime water pump. (see page 10) • Turn fuel valve to the ON position.(Fig 8-A) •... -
Page 13: Maintenance
OPERATION Draining Pump Chamber (See Fig • Remove Drain Plug and drain Pump Chamber. PUMP DRAIN PLUG • Remove Filler Cap and flush Pump Chamber with clean, fresh water. (CLEAN OUT PORT) • Let Pump Chamber drain again. • Reinstall Filler Cap. •... -
Page 14: Changing Oil
MAINTENANCE Changing Engine Oil (See Fig 11) Engine oil will drain better if the engine is still warm, but not hot. • Shut off engine. • Clean the area around the oil fill cap / dipstick to keep out debris then remove oil fill cap / dipstick. •... -
Page 15: Cleaning Air Filter
MAINTENANCE Air Cleaner (See Fig 13) A dirty air filter will reduce the life span of the engine, make starting the engine difficult, and reduce the unit’s performance. If operating pump in dusty conditions, clean air filter more frequently then specified in the maintenance schedule. •... -
Page 16: Storage
STORAGE Storing Trash Pump Proper storage prevents the development of rust and corrosion which affects the pumps performance and appearance. Proper storage also makes it easier to start the engine when using the pump again. If storing water pump for 30 days or more follow the below procedures: If pump has been running, allow engine to cool for at least 30 minutes before taking the steps CAUTION! - Page 17 STORAGE Lubricate Pump Coat areas of pump that might rust, such as areas with damaged paint, with a light film of oil. Use a silicone spary lubricant and lightly lubricate controls. Drain Fuel Tank and Fuel injection pump assembly • For long term storage (over 90 days) drain fuel from fuel tank and fuel injection pump assembly.
-
Page 18: Troubleshooting
TROUBLESHOOTING PROBLEM CAUSE SOLUTION Engine Does Not Start Check controls Engine OFF/ON switch is in the “OFF” Turn Engine OFF/ON switch to the “ON” position position Fuel valve in “OFF” position Turn Fuel valve to “ON” position Check fuel Out of fuel Fill fuel tank Stale fuel or water in fuel Drain fuel tank and fuel injection pump... -
Page 19: Modifications
Damage to fuel system caused by the use of oxygenated fuels is not covered under the WARNING! warranty WARNING! Never operate this unit if there are any broken or missing parts and only use Ford WARNING! replacement parts specifically designed for this unit. •...