Panasonic LS-H Series Instruction Manual

Laser Sensor Head
LS-H Series
Thank you very much for purchasing Panasonic products. Read this Instruction
Manual carefully and thoroughly for the correct and optimum use of this product.
Kindly keep this manual in a convenient place for quick reference.
Never use this product as a sensing device for personnel protection.
●
In case of using sensing devices for personnel protection, use
●
products which meet standards, such as OSHA, ANSI or IEC etc.,
for personnel protection applicable in each region or country.
Do not view direct beam by the unprotected eye or with an
●
optical instrument. Lasers are potentially hazardous.
WARNING
Use of control or adjustment or performance of procedures
●
other than those specified in this instruction manual may
result in hazardous radiation expose.
1 FOR SAFE USE OF A LASER PRODUCT
● In order to prevent the accident by laser product and protect the users,
JIS C 6802 "Safety of laser products" was established based on the
-2014
regulation of IEC (International electrotechnical Commission). This
regulation classifies laser products according to the level of hazard, and
provides the safety measures for respective classes.
This product are classified as "Class 2 laser products" according to
IEC 60825-1 (JIS C 6802
-2014
● Laser hazardous class
Classification according to IEC 60825-1
Class
Class 2 Visible beam, low power. Blink response of eye affords protection.
The following label is affixed on this product in accordance with the
●
Safety of laser product.
Warning label
・
In Japanese
(Based on JIS C 6802
クラス1レーザ製品
JIS C 6802
<Label position>
Direction of
laser emission
● When this product is used in China,
affix the chinese warning label
(accessory) on the label in the
product.
● If the affixed label on this product may not be visible after installation of
the product, affix the accessory lable close to the product where you can
see.
In Japanese
・ Laser emission indicator (green)
While laser is emitted, the laser emission indicator (green) of the sensor
head lights up.
This indicator is visible even when wearing laser protective glasses.
Direction of
laser emission
INSTRUCTION MANUAL
MJE-LSH No.0059-56V
"Safety of laser products".
-2014)
(JIS C 6802
-2014 -2014
Description of hazardous evaluation
In English
) (Based on IEC 60825-1
-2014
Direction of
laser emission
In Chinese
(Based on GB 7247.1
In English In Chinese
Operation indicator (Orange)
Laser emission indicator (Green)
2

SPECIFICATIONS

Item Model No. (Note 1)
Applicable amplifier
H-SP mode
Sensing
FAST mode
range
STD mode
(Note 4)
U-LG mode
Operation indicator
Laser emission indicator
Ambient temperature
Ambient humidity
Emitting element
Material
Cable
Weight
Accessories
Notes: 1) The model No. with suffix '-C5' stands for the 5m cable length type.
(e.g.) LS-H91-C5
2) The model No. of retroreflective type sensor with the suffix '-Y' is the sensor without the RF-330
and RF-230 reflector. Arrange the reflector separately.
(e.g.) LS-H91-Y
3) LS-H22 is the model No. for the long sensing range spot reflective type (LS-H21) with the
lens attachment for line reflective type (LS-MR1). 'LS-H21' is indicated on the actual product.
4) Configure the mode settings in the applicable amplifier LS-400 series.
)
3 CAUTIONS
This product has been designed to meet the specifications when it is used
along with the optional exclusive amplifier. If an amplifier other than the
exclusive amplifier is used, not only the specifications may not be met, but
it may also be a cause for malfunction or break down. Hence, please
ensure to use this product along with the optional exclusive amplifier.
)
-2014 This product has been developed / produced for industrial use only.
●
Always use the sensor with the connector to be joined to the amplifier.
●
Make sure that the power is off while wiring to the amplifier.
●
In case noise generating equipment (switching regulator, inverter motor
●
etc.) is used in the vicinity of this product, connect the frame ground
(F.G.) terminal of the equipment to an actual ground.
If power is supplied from a commercial switching regulator, ensure that
●
the frame ground (F.G.) terminal of the power supply is connected to an
actual ground.
Do not use the sensor during the initial transient time (0.5 sec.) just after
●
the power supply is switched on.
Do not run the wires together with high-voltage lines or power lines or put
●
them in the same raceway. This can cause malfunction due to induction.
Take care that the sensor head is not directly exposed to fluorescent
●
lamp from a rapid-starter lamp or a high frequency lighting device, as it
may affect the sensing performance.
)
-2012
The sensor head cable cannot be extended.
●
Make sure that stress is not applied to the sensor head cable joint.
●
This sensor is suitable for indoor use only.
●
Do not allow any water, oil fingerprints, etc., which may refract light, or
●
dust, dirt, etc., which may block light, to stick to the emitting/receiving
surfaces of the sensor head. In case they are present, wipe them with a
clean, soft cloth or lens paper.
Do not use the sensor in vaporous, dusty or corrosive gas atmospheres.
●
Take care that the sensor does not come in contact with water, oil,
●
grease or organic solvents, such as, thinner, etc.
Make sure that the power is off while cleaning the emitting/receiving
●
windows of the sensor head.
Coaxial retroreflective type (Note 2)
Type
Long sensing
range
LS-H91 LS-H92
LS-400 series
0.1 to 3m 0.2 to 10m
0.1 to 3m 0.2 to 10m
0.1 to 5m 0.2 to 20m
0.1 to 7m 0.2 to 30m
Orange LED (Lights up when amplifier output is ON)
Green LED (Lights up when laser is emitted)
-10 to +55℃ (No dew condensation or icing allowed), Storage: -20 to +70℃
35～85% RH, Storage: 35～85% RH
Red semiconductor laser Class 2 (IEC/JIS/GB/KS standard)
(Max. output: 3mW or less, Peak emission wavelength: 655nm)
Enclosure: PBT (Attachment: PEI), Lens cover: Acrylic
0.1mm shielded cable, 2m long
2
30g approx.
Connector for Connector for
amplifier: 1 pc. amplifier: 1 pc.
RF-330 (Reflector) RF-230 (Reflector)
: 1 pc. : 1 pc.
Warning label Warning label
Japanese / English Japanese / English
/ Chinese / Chinese
: 1 set : 1 set
Diffuse reflective type
Long sensing range Long sensing range
spot reflective line reflective
LS-H21 LS-H22 (Note 3)
30 to 300mm 30 to 300mm
30 to 300mm 30 to 300mm
30 to 500mm 30 to 500mm
30 to 1,000mm 30 to 1,000mm
Connector for
amplifier: 1 pc.
Connector for
LS-MR1 (Lens
amplifier: 1 pc.
attachment for line
Warning label
reflective type): 1 pc.
Japanese / English
Warning label
/ Chinese
Japanese / English
: 1 set
/ Chinese
: 1 set