Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Manual
Advertisement
Table of Contents
Related Manuals for Organic Lighting Systems liniLED Top
Summary of Contents for Organic Lighting Systems liniLED Top
- Page 1 LED strip manual liniLED® Top 1.2 in ADAM V DC RoHS IP40/IP68 CLEANING FROST POOL CL POOL CL BEND S D C M...
- Page 2 LED strip Top General Installation Operation and use Warning Cable selection Area advice Product care and handling 6/7. Cutting instructions 8/9. Soldering 10/11. Connect IP40 Power supply Symbols...
-
Page 3: Installation
General Read the instructions and safety precautions before installation, usage and storage of the products to secure safety of the user and reliability of the product. - Hand over the instructions to the end-user and those responsible for installation and usage. - Organic Lighting cannot be held responsible for improper handling, product installation, usage or storage. -
Page 4: Area Advice
Area advice Depending on the area where the liniLED® LED strip is installed we offer a range of solutions to cope with external factors. The product portfolio includes a range of IP40 and IP68 connectors. Below the different connectors are displayed for use in different environments. Indoor environment (IP20) Solder... - Page 5 LiniLED TOP Product care and handling 1.2 in 1.2 in Maximum bending radius is 1.2 inches. Only bend up or downward. Do not compress or stretch the LED strip. Do not bend the LED strip sidewards. Do not twist the LED strip.
-
Page 6: Cutting Instructions
Cutting instructions Turn off the power before cutting the LED strip. Side view | Make sure the cut is vertical as illustraded in the image Top view | Make sure the cut is vertical as illustraded in the image above. above. - Page 7 Cutting instructions Place the liniLED® LED strip on the base of the cutting tool. Not doing so may result in a deformed LED strip. LED strip manual | liniLED® Top...
- Page 8 Solder Turn off the power. Make sure the wires are not under electric current. 0.31 in 0.019 in Solder the wires to the PCB. We advise to use a cable with an area Top view | Only cut the LED strip extrusion on the dotted line of the not bigger then 0.019 in2.
- Page 9 Pre-solder the connector pads. Pre-solder the wires. 662o F 662o F Solder the wires to the connector pads. Connect the liniLED® LED strip to the power supply (24 V DC) constant 662o F voltage. LED strip manual | liniLED® Top...
- Page 10 Connect IP40 Take into account the direction of the arrow on the bottom of the The liniLED® IP40 Connector consists of: End cap (1), Shell (2), Connector (3), Clamp (4). liniLED® LED strip and allign it with the arrow on the clamp (4). Place the shell (2) over the LED strip.
- Page 11 Slide the clamp (4) over the connector (3) and make sure that Slide the shell (2) partly over the clamp (4). the arrow is on the upper side. ‘ Click ’ Slide the shell (2) entirely over the clamp (4) and push firmly until Test the liniLED®...
-
Page 12: Power Supply
Power supply Turn off the power before connecting the LED strip to the power supply. 120/277 VAC Power Supply 24 V DC Cable X liniLED® Cable 3.28ft Connect the LED strip as indicated in the figure above. The wires should be connected as follows: Red (+) and Black (-). Insert the power plug. - Page 13 Symbols Manufacturer’s declaration that the product meets the applicable EC directives. Suitable for mounting on all surfaces and suitable to cover with insulating material. Restriction of Hazardous Substances (RoHS): product complies with the RoHS directive and each homogeneous material does RoHS not exceed the limits for the materials mentioned under the RoHS directive (Pb, Hg, Cd, Cr6+, PBB and PBDE).
- Page 14 liniLED® is a registered trademark of Organic Lighting Subject to misprints, errors and modifications. No legal rights can be derived from this document. V0917...