Sony PEG-UX50 Service Manual page 4

1-2-2. Keyboard Check
1. Using the JOG dial, move the cursor to the [Keyboard Check]
position.
2. Press the JOG dial once, and the following check screen will
appear. Key Board LED turns on.
PEG-UX50/U, UX40/U
(Display)
Keyboard Check
1 R
2 T
3 Y
4 U
5 I
6 O
7 P
8
9 A
0 S
BS D
Q F
W G
E H
PEG-UX50/E
(Display)
Keyboard Check
1 R
2 T
3 Y
4 U
5 I
6 O
7 P
8 @
9 A
0 S
BS D
Q F
W G
E H
3. If each key is judged normal, "OK" will be displayed to each
key name.
4. If "OK" is displayed to all keys, the [TEST MODE] screen
will come back automatically.
1-2-3. LCD Flip Check
1. Using the JOG dial, move the cursor to the [LCD Flip Check]
position.
2. Press the JOG dial once, and the following check screen will appear.
Also, in such a case, each LED will be lit as follows.
Power LED : Orange and green blink alternately.
REC LED : Red turn on.
MS LED : Orange turn on.
Bluetooth LED : Blue blinks.
Wireless LAN LED : Green turn on. ..... (UX50)
(Display)
LCD Flip
LCD
Rotation
LCD
Flip
Camera
Rotation
3. Rotate the LCD clockwise by a half turn and return it to
original position. If "LCD Rotation
the LCD rotation detection is normal.
4. Open and close the LCD, and if "LCD Flip
displayed, the LCD flip detection is normal.
5. Rotate the camera and return it to original position. If
"Camera Rotation H 1" is displayed, the camera rotation
detection is normal.
6. Press the Back button to return to the [TEST MODE] screen.
J TAB
K FNC
L SPC
SHFT ;
Z :
X
C PGDN
V
B
N
M
PGUP
ENT
CTRL
J TAB
K FNC
L SPC
SHFT ;
Z :
X
C PGDN
V
B
N
M
PGUP
ENT
CTRL
(Display)
LCD Flip
LCD
Rotation H 1
LCD
Flip H 1
Camera
Rotation H 1
H 1" is displayed,
H 1" is
1-2-4. Touchpanel Check
1. Using the JOG dial, move the cursor to the [Touchpanel
Check] position.
2. Press the JOG dial once, and the following check screen will
appear.
(Display)
No. 1
Limit 10 10
Raw 0 0
3. Tap the upper left corner indicated with a "X" mark of the
LCD screen shown above, and the screen will change over to
the next screen.
4. Perform the same operation on the No.2 (lower right), No.3
(upper right), No.4 (center), and No.5 (lower left) screens
respectively, and the tap check screen as shown below will
appear.
(Display)
Touchpanel Check
X
(10,10)
X
(50,50)
X
(100,100)
Note: If the adjustment in step 3 and 4 is disordered,
an error will occur in the tap position check.
5. Press the Back button to return to the [TEST MODE] screen.
1-2-5. Display Check
1. Making of image data.
1) Format the "Memory Stick" with the CLIE.
2) Using the PC, select the following files from the "Writing
tool soft" and copy them to the "Palm" folder in the "Memory
Stick" formatted in step 1).
• Writing tool soft_UX50
• sample1.bmp
• sample2.bmp
3) Insert the "Memory Stick" used in step 2) into the "Memory
Stick" connector of the CLIE.
2. Using the JOG dial, move the cursor to the [Display Check]
position.
3. Press the JOG dial once, and the [Display Check] screen will
appear.
4. Each time the JOG dial is rotated, the check screen will
change.
(If the JOG dial is rotated 11 times, the initial screen will
come back.)
5. Press the Back button to return to the [TEST MODE] screen.
1-2
X
(140,140)
(or _UX40U) \ Sample \
*
Confidential