Lorex N841 Series Quick Setup Manual page 2

Adding Cameras from the LAN
Follow the steps below to add cameras that are not directly connected to the Power
over Ethernet (PoE) ports on the back of the recorder.
NOTE: Please visit lorex.com/compatibility
To add cameras from the LAN:
1. Connect the camera to a router or switch on the same network as the recorder.
2. Right-click and select Device Search. If prompted, log in using the system user name (default:
admin) and your new, secure password.
3. Configure the following:
a. Click Device Search.
b. Check the camera(s) you would like to
add.
c. Click Add. The status indicator
turns green to show the camera is
successfully connected.
d. The added device(s) will appear in the
Added Device list. Right-click to exit to
live view.
NOTE: If the icon in the Status column
appears red, there may be a password
issue with the camera. Select the
camera and click Reconnect IPC.
Setting Date and Time
It is important to set the correct time to ensure accurate time stamps on recordings.
To set date and time:
1. In live view, right-click and click Main Menu. If prompted, log in using the system user name
(default: admin) and your new, secure password.
2. Click and select Setting.
3. Click General and select the Date & Time tab.
4. Configure the following:
a. Enter the current time and select your
time zone, and click OK.
b. Check DST to enable auto Daylight
Savings Time updates.
c. (Optional) Check NTP to sync your
system with an Internet time server.
Click Manual Update to instantly
update the time.
NOTE: A constant Internet connection
is required to use NTP.
5. Click Apply to save changes.
Playback and Search
Search through and play video recordings from the hard drive.
To search for and play recordings:
1. From live view, right-click and then click Playback. If prompted, log in using the system user
name (default: admin) and your new, secure password.
2. Configure the following:
a. Use the calendar on the right
to select the date to playback.
b. Check channels you want to
play back. Click the grey icon
beside each selected channel
to select Mainstream (M) or
Substream (S) video quality.
c. Click inside the video bar to
select the playback time.
Playback starts immediately at
the selected time.
Backup
Back up recordings from the hard drive to a USB flash drive (not included).
To back up recordings:
1. Insert a USB flash drive (not included) into a free USB port on the recorder.
2. From live view, right-click and then click Main Menu. If prompted, log in using the system user
name (default: admin) and your new, secure password.
3. Click , then click BACKUP.
4. Configure the following:
a. Select the type and quality of
recordings to search for.
b. Select the channel(s) to search
by.
c. Select a Start Time and End
Time for your search.
d. Choose a file format for your
backed up files.
e. Click Add to see recordings
that match your search.
f. Check boxes next to recordings
you want to back up, then
click Start. You may also click
Onekey Backup to back up all
files that match your search.
Once you have completed all steps for initial setup on the front of this guide, please refer
to the following sections to learn more about using your system.
for a list of compatible Lorex IP cameras.
a
b
c
a
b
c
c
a
c
Advanced Motion Detection & Deterrence Settings
Configure advanced motion detection and/or active deterrence settings. For a complete
list of compatible cameras, navigate to your recorder series at lorex.com/compatibility.
To configure advanced person/vehicle detection or active deterrence:
1. In live view, right-click and click Main Menu. If prompted, log in using the system user name
(default: admin) and your new, secure password.
2. Click
3. Configure the following:
a. Select the channel of
a connected camera
with person and vehicle
detection.
b. Check Enable
underneath Person
and/or Vehicle.
Figure 1: Detection Area
• The default schedule, shown in Figure 2, is active during
the night, between 5pm and 7am.
• Click Set to change the schedule for the corresponding
day of the week.
• Click OK when finished.
a. Select the channel of a
a
connected deterrence camera.
b. Check Enable.
b
c. Click Set next to Area to set
active areas for person and/or
vehicle detection. See Figure 3
below for details.
Figure 3: Deterrence Area
To set off all connected deterrence cameras' warning lights and
sirens, press and hold the front panel button for 3 seconds.
Changing the Recorder's Output Resolution
To ensure the best possible picture quality, set the recorder's output resolution to
match the highest resolution supported by your monitor.
IMPORTANT:
b
supported by the new monitor before switching.
d e
To change the recorder's output resolution:
1. From live view, right-c lick and then click Main Menu. If prompted, log in using the system user
name (default: admin) and your new, secure password.
2. Click Display, then configure the following:
a. Set Resolution to match the
highest resolution supported
by your monitor. For example,
select 3840×2160 for 4K
f
monitors, or 1920×1080 for
1080p.
b. Click OK. The recorder will
restart before changes take
effect.
, then select EVENT. Select the Deterrence tab.
Option 1: Advanced Person/Vehicle Detection Cameras
a
b
c
d
e
c. Click Set next to Area to set active areas for person and/or
vehicle detection. See Figure 1 below for details.
d. Click Set next to Schedule to set a weekly schedule for person
and/or vehicle detection. See Figure 2 below for details.
e. Set preferences for the warning light and siren.
f. Click OK.
• Click Add to set an area for person or vehicle
detection on the selected channel. Click-and-drag
the corners to resize the area.
• For most accurate results, set an area where objects
of interest will move within the bounding box as well
as into / out of.
• Check Light next to a rule to flash the camera's
warning light when an object is detected.
• See your camera's documentation for optimal
camera positioning for person and vehicle detection.
Option 2: Active Deterrence Cameras
a
b
c
d
e
d. Click Set next to Schedule to set a weekly schedule for
person and/or vehicle detection. See Figure 2 above for
details.
e. Set preferences for the warning light and siren.
f. Set Sensitivity and Threshold levels to your preference.
g. Click OK.
• The camera image appears with a grid overlay. The
green area is the active area for deterrence.
• Click or click-and-drag to add / remove boxes from
the active area.
• In Figure 3, only motion around the doorway will
trigger the warning light.
• Right-click when finished.
If you need to switch the monitor, make sure you set the recorder to an output resolution
a
f
Figure 2: Deterrence Schedule
f
g
b
N841_QSG_EN_R1