Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for GDC PMA-1000
Summary of Contents for GDC PMA-1000
- Page 1 PMA-1000 POWER MANAGEMENT ADAPTER INSTALLATION MANUAL AUG 2015...
-
Page 2: Table Of Contents
3.7 Power Supply Connection to the Device Sockets..........15 3.8 Power Supply Connection to the Screen Masking System ......16 3.9 Power Supply Connection to the PMA-1000 ............17 4. Software Configuration ................. 18 4.1 Setting up IP Address .................... 18 4.2 Adding a New Device ..................... - Page 3 Lobby B, #06-25 Sorocaba/SP – Brasil Singapore 408564 Tel: +51 1 340 5146 Tel: +1 818 972 4370 / Tel: +55 15 33269301 Tel: +65 6222 1082 +1 877 743 2872 (Toll Free) Aug 2015 PMA-1000 Power Management Adapter Installation Manual...
- Page 4 Tel: +81 3 5524 2607 Tel: +91 22 4044 0500 Tel: +52 55 8851 1198/ ___+52 55 8851 1165 United Arab Emirates (Dubai) Business Centre, Dubai World Central, PO Box 390667, Dubai UAE PMA-1000 Power Management Adapter Aug 2015 Installation Manual...
-
Page 5: Introduction
Together with Theatre Management System (TMS) and Quality Management System (QMS), unmanned projection can be achieved, based on the foundation of automated projection. 2. Packing List The PMA-1000 package includes two boxes: the main package and the accessories package. Details are shown below: PMA-1000 Packing List Seq. - Page 6 2.5 mm electrical wires (with crimped ring terminals) International standard cables (with quick-connecting terminals) International standard power cord Metal conduits and plastic clips, rubber plugs, self-tapping Several screws and other supplementary parts PMA-1000 Power Management Adapter Aug 2015 Installation Manual...
-
Page 7: Hardware Installation
3. HARDWARE INSTALLATION 3. Hardware Installation The PMA-1000 power management device adopts wall-mounted installation. It is usually installed adjacent to the power distribution cabinet in the projection room (as shown in the photo below). The device has four output ports at the bottom for cable connection and two on each side for backup. - Page 8 & female quick-connecting sockets. The lighting system, device sockets, aux-a and aux-b have regular 220V power loading, and thus they are connected via one quick-connecting socket. The PMA-1000 is a device with 220V input voltage. PMA-1000 Power Management Adapter...
- Page 9 3. HARDWARE INSTALLATION Detailed connector arrangement sequence and illustrations are shown below: Aug 2015 PMA-1000 Power Management Adapter Installation Manual...
-
Page 10: Device Installation And Cabling
Attach 4 nuts onto the drilled holes to secure the suitable positions of the power distribution cabinet for metal conduits. cabling. Mount the PMA-1000 on the wall with a suitable Secure one end of the conduit onto the power distance from the power distribution cabinet. distribution cabinet. -
Page 11: Power Supply Connection To The Projector
2. Connect the “neutral wire in” from the PMA to the existing neutral wire underneath the projector circuit breaker, and then connect both to the circuit breaker. Connect the “live wire in” from the PMA to the live wire port underneath the projector circuit breaker. Aug 2015 -11- PMA-1000 Power Management Adapter Installation Manual... -
Page 12: Power Supply Connection To The Ventilation System
2. Connect the “three live wires out” from the PMA existing three live wire connections underneath the ventilation system circuit breaker. Note: The connection sequence of these three live wires must be consistent. If not, electrical inversion may occur. PMA-1000 Power Management Adapter -12- Aug 2015 Installation Manual... -
Page 13: Power Supply Connection To The Audio System
2. Connect the “neutral wire in” from the PMA to the existing neutral wire underneath the audio system circuit breaker and then connect both to the circuit breaker. 3. Connect the “live wire in” from the PMA to the live wire port underneath the audio system circuit breaker Aug 2015 -13- PMA-1000 Power Management Adapter Installation Manual... -
Page 14: Power Supply Connection To The Lighting System
Note: If a leakage protection switch is in use, the neutral wire can only be connected to this specific neutral wire port on circuit breaker. It cannot be connected to the public neutral wire port, or else the circuit breaker will be triggered. PMA-1000 Power Management Adapter -14- Aug 2015... -
Page 15: Power Supply Connection To The Device Sockets
2. Connect the blue wire to the live wire port underneath the socket circuit breaker. 3. Connect the yellow and green wire to the neutral wire port underneath the socket (the leakage protection switch). Aug 2015 -15- PMA-1000 Power Management Adapter Installation Manual... -
Page 16: Power Supply Connection To The Screen Masking System
PMA to the existing three live wire connections underneath the screen masking system circuit breaker. Note: The connection sequence of these three live wires must be consistent. If not, electrical inversion may occur. PMA-1000 Power Management Adapter -16- Aug 2015 Installation Manual... -
Page 17: Power Supply Connection To The Pma-1000
3. HARDWARE INSTALLATION 3.9 Power Supply Connection to the PMA-1000 The PMA-1000 uses a regular 220V power supply. Thus only a three-pin international standard cable (with quick-connecting terminals) is required. On the PMA, connect a three-pin cable to the “system power supply”. -
Page 18: Software Configuration
IP configuration software (IP & MAC Config V2.1.1.exe) on the laptop, click 'Advanced', followed by 'Search', the current IP address of the PMA-1000 will be shown, as well as the current IP of the laptop. Only when both IPs are on the same network port, the IP of the PMA will appear in black, otherwise it will appear in grey, which implies the inaccessibility to the IP modification main interface. - Page 19 Step 2: Modify the IP address Step 1: Modify the gate address Note: The network between PMA-1000 and TMS (Theatre Management System) must be in connection sustainably, to ensure that TMS can control the PMA at any time. Aug 2015 -19-...
-
Page 20: Adding A New Device
4.2 Adding a new device PMA-1000 can be added and configured at the Screen tab of TMS software. Click ‘Automation’ under ‘Device’ tab. A window will pop up. Select the device model, fill in the device information, IP address and select the located Hall number. -
Page 21: Remote Control Of Power Connection/Disconnection
Monitoring tab, and the Automated Management window will pop up. Select the 'PMA-1000 Controls' subtab, individual power supply circuit can then be controlled. Note: The blue timeline represents the screening period. If the current time is within the screening period, only power connection operation is available and power disconnection operation is invalid. - Page 22 Cert. No. CN09/32221 GDC manufacturing facility is ISO 9001: 2008 certified. Copyright © 2016 GDC Technology Limited. All rights reserved. All trademarks listed in this manual are properties of their respective owners. Specifications are subject to change without notice due to ongoing product development and improvement.