Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Chamberlain ACXL
Summary of Contents for Chamberlain ACXL
- Page 1 Large Display Access Controller INSTALLATION MANUAL...
- Page 2 Safety Safety Symbol and Signal Word Review When you see these Safety Symbols and Signal Words on MECHANICAL the following pages, they will alert you to the possibility of serious injury or death if you do not comply with the warnings that accompany them.
-
Page 3: Table Of Contents
INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL PROGRAMMING INTRODUCTION Carton Inventory ..............4 Tools Needed ................4 Dimensions ................5 System Specifi cations ............. 5 Wire Specifi cations ..............6 PRE-INSTALL Internet Service ............... 7 SIP Provider ................7 Setup a LiftMaster Cloud Account ........... 7 INSTALL Remove Knockouts .............. -
Page 4: Carton Inventory
INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL PROGRAMMING Carton Inventory Controller Gooseneck Gasket Power Supply Radio Antenna (Security+ 2.0 ® and Cable Keys (2) Ferrite Core S10K30MOV 1N4005 Diode Kit (4) Wi-Fi ® Antenna and Cable (Metal Oxide Varistor)(4) PROVIDED (NOT SHOWN) •... -
Page 5: Dimensions
INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL PROGRAMMING Dimensions 4-3/4" (10.2 cm) FRONT VIEW SIDE VIEW BACK VIEW 14" (35.6 cm) 4-1/4" (10.8 cm) E = Electrical Wiring BOTTOM VIEW P = Pedestal Mount S = Surface Mount R = Radio Antenna 10-7/8"... -
Page 6: Wire Specifi Cations
INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL PROGRAMMING Wire Specifi cations Use this chart to pull wires in preparation of your installation. DESCRIPTION OF WIRE RUN WIRE SPECIFICATION MAXIMUM RUN DISTANCE Power Wire, secondary DC output 2-Conductor 14 AWG Up to 60 feet (18.3 m) 2-Conductor 16 AWG Up to 37 feet (11.3 m) 2-Conductor 18 AWG... -
Page 7: Internet Service
INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL PROGRAMMING Internet Service The controller MUST be configured with the proper network settings to operate. NETWORK Internet service provider: Wi-Fi Network Name: Wi-Fi Password: Automatic IP addressing: DHCP (preferred setting) Static IP Addressing: (NOTE: Write down the following for future reference: IP, Netmask, Gateway, Primary, Secondary, Server Port) SIP Provider Phone.com is the preferred SIP provider. -
Page 8: Remove Knockouts
INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL PROGRAMMING Remove Knockouts Turn the key clockwise and open the controller. To prevent damage to the controller from moisture or water: • DO NOT install during rain. Internal components MUST be Identify which knockouts need to be removed kept free from of water and moisture. -
Page 9: Mount The Controller
INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL PROGRAMMING Mount Controller Make sure the controller is properly sealed to prevent damage to the controller from Attach the goose-neck gasket (provided) if mounting to a goose-neck. moisture. 2. Mount the controller securely to a fl at surface or pedestal with appropriate hardware taking care to route wiring through appropriate knockouts. -
Page 10: Controller Overview
INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL PROGRAMMING Controller Overview ® Wi-Fi ANTENNA SENSOR BOARD CAMERA MOUNTING BRACKET RADIO ANTENNA POWER/INTERNET BOARD RADIO ANTENNA Wi-Fi ® ANTENNA CONNECTION CONNECTION LOOP DETECTOR CONTROL BOARD BOARD MOUNTING LOCATION POSTAL LOCK SWITCH DOOR BOARD 1 DOOR BOARD 2 (Doors 1 &... -
Page 11: Power/Internet Board Overview
INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL PROGRAMMING Power/Internet Board Overview Speaker Dip Switches Audio Postal Lock LOOP BOARD (not used) Sensor Board Display Backlight Display (Touch) Auxiliary Power (not used) Power Connection for Control Board Door Board 2 RADIO ANTENNA POWER Door Board 1 ETHERNET... -
Page 12: Door Board Overview
INSTALL NETWORK ACCESS CONTROL PROGRAMMING Door Board Overview The ACXL has a combination of access control inputs/outputs on the Door Boards that work in conjunction to control up to 4 access points. DOOR BOARD 1 DOOR BOARD 2 Door 1... - Page 13 INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL PROGRAMMING Install Antennas The radio antenna and Wi-Fi ® antennas must be a minimum of 8 inches (20 cm) apart. Install the antennas on opposite sides of the controller. Optional antenna cable kits are available for remote antenna mounting (refer to accessories). Security+ 2.0 ®...
-
Page 14: Install The Ground
INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL PROGRAMMING Install the Ground IMPORTANT: An earth ground rod is strongly recommended and should be no To AVOID damaging gas, power or other underground utility lines, further than 12 feet (3.7 m) from the controller and use a minimum of 12 gauge contact underground utility locating wire in most cases. -
Page 15: Connect Power
INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL PROGRAMMING Connect Power The outlet for the controller MUST be an external dedicated 120 Vac outlet • DO NOT use ANY power supply other located within 60 feet (18.3 m) cable run of the controller. This outlet than those supplied with your controller.
Need help?
Do you have a question about the ACXL and is the answer not in the manual?
Questions and answers