Advertisement
Quick Links
®
The FLUSH GENIE is a fully programmable automatic flush control device for urinals and toilets. The smart design allows the
device to be switched between sensor activated mode and timer controlled mode.
When in SENSOR activated mode, the unit sends out an infrared beam that senses a user on a urinal or toilet. Once the user
walks away from the fixture the unit triggers the fixture to flush automatically. The unit includes an electronic push button to allow
for a manual courtesy flush option.
When in TIMER controlled mode, the unit converts most urinals into water efficient fixtures by controlling the amount of daily
flushes. The flush intervals can be programmed to flush once every 30 minutes, 1, 2, or 3 hours. The unit will go to SLEEP if a
user is NOT detected within 135 minutes since the last use to prevent flush activation while the facility is closed. A mechanical
manual flush override using the provided MANUAL FLUSH KEY will allow the custodial staff (not the user) to flush the unit
manually at any time (NOTE: electronic push button is deactivated in TIMER mode).
<
Components
Collar
Gasket
=
Installation
Pre-Installation Note:
Although not necessary, it is recommended to shut off
water supply at stop.
c
Using the supplied collar wrench, loosen handle
from flush valve.
d
Remove handle from flush valve.
Note: A small amount of water may drip out while
removing handle so be prepared to collect
it with a rag or towel.
e
Place collar gasket into collar nut and attach the
®
Flush Genie unit where the handle was removed.
f
Tighten collar nut using the supplied collar wrench.
Note: Save removed handle in case you need to reuse
for service of Flush Genie unit.
HSM-801-R-FG
Series
User Approaches
Senses User
Manual
Unit
Flush Key (2)
®
Page 1
FLUSH GENIE
SIDEMOUNT for Urinals and Toilets
Installation and Operation Manual
Flushes When
User Leaves
Battery
Compartment
Wrench
Four (4) "C" Cell
Alkaline Batteries
(Factory Installed)
c
Collar
Wrench
e
Collar
Collar Nut
Gasket
User Approaches
Senses User
Collar
Wrench
d
f
®
User Leaves
Advertisement
Related Manuals for AMTC FLUSH GENIE HSM-801-R-FG Series
Summary of Contents for AMTC FLUSH GENIE HSM-801-R-FG Series
- Page 1 ® FLUSH GENIE HSM-801-R-FG SIDEMOUNT for Urinals and Toilets Series Installation and Operation Manual User Approaches Senses User User Approaches User Leaves Flushes When Senses User User Leaves ® The FLUSH GENIE is a fully programmable automatic flush control device for urinals and toilets. The smart design allows the device to be switched between sensor activated mode and timer controlled mode.
- Page 2 > Adjusting Modes of Operation The unit includes two (2) different modes of operation. Timer Mode and Sensor Mode. Remove side cover using battery compartment wrench and refer to the “Mode Adjustment Guide” for switch settings (see diagrams below). In TIMER Mode, the unit converts most urinals into water efficient fixtures by controlling the amount of daily flushes.
- Page 3 Mode Operation and Features TIMER MODE (FOR URINAL USE ONLY) 1. Select switch sequence for preferred time interval. 2. Plug in battery connector (unit will flush once). Interval program will begin counting. 3. Unit is now activated. 4. Re-install battery cover. 5.
-
Page 4: Battery Replacement
Visual Indicator Guide Red LED Red LED Constant blinking red LED indicates user being detected. Constant blinking red LED when user not present indicates batteries are low and need replacing. Electronic Push Button Allows manual activation of flush when needed in SENSOR MODE ONLY. -
Page 5: Warranty
FOR A PERIOD OF FIVE (5) YEARS FROM DATE OF PURCHASE, WHEN PROPERLY INSTALLED AND UNDER NORMAL USE AND SERVICE. THESE PROVISIONS DO NOT INCLUDE THE BATTERIES SHIPPED WITH THE PRODUCTS. A DEFECTIVE PRODUCT MAY BE RETURNED TO AMTC OR ITS AUTHORIZED REPRESENTATIVES WITHIN FIVE (5) YEARS FROM DATE OF PURCHASE WITH THE PROPER INVOICE OF PURCHASE.
Need help?
Do you have a question about the FLUSH GENIE HSM-801-R-FG Series and is the answer not in the manual?
Questions and answers