Bosch GSH 16-28 Original Instructions Manual page 7

formed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Service
Have your power tool serviced by a qualified repair
u
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Hammer Safety Warnings
Wear ear protectors. Exposure to noise can cause hear-
u
ing loss.
Use auxiliary handle(s), if supplied with the tool. Loss
u
of control can cause personal injury.
Hold power tool by insulated gripping surfaces, when
u
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting ac-
cessory contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the operator
an electric shock.
Use suitable detectors to determine if utility lines are
u
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Hold the power tool firmly with both hands and make
u
sure you have a stable footing. The power tool can be
more securely guided with both hands.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The machine is intended for heavy chiselling and demolition
work as well as for driving in and compacting with the appro-
priate accessories.
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
Bosch Power Tools
(1) Handle (insulated gripping surface)
(2) On/off switch
(3) Carrying handle
(4) Knurled nut for carrying handle
(5) Lock bolt (GSH 16-30)
(6) Tool retainer (GSH 16-28)
(7) Tool shank
(8) Tool holder
(9) Shoulder
Technical data
Demolition ham- GSH 16-28
mer
Article number 3 611 C35 0.. 3 611 C35 1..
Rated power input W
-1
Impact rate min
Impact energy per J
stroke according to
EPTA-Procedure
05/2009
Tool holder mm
Weight according kg
to
EPTA-Procedure
01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Assembly
Carrying handle
The carrying handle (3) can be swivelled to any position.
Loosen the knurled nut (4), rotate the carrying handle (3)
around the axis of the tool to the required position and then
retighten the knurled nut (4).
The carrying handle (3) can also be repositioned so that it is
on the other side of the tool. Completely unscrew the
knurled nut (4) and then pull the hexagon bolt upwards and
out. Take off the carrying handle (3) from the side and rotate
the remaining clamping element by 180°. Fit the carrying
handle (3) again by following the steps in reverse order.
Changing the tool (GSH 16-28)
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Clean the tool shank (7) and apply a light coat of grease.
Application tools without collar (see figures A – B)
– Pivot the tool retainer (6) upwards by approx. 150° and
insert the application tool into the tool holder (8).
English | 7
GSH 16-30
1750 1750
1300 1300
41 41
28 30
18.3 16.9
/ II / II
1 609 92A 23U | (01.02.2019)