Advertisement
Quick Links
Product: D8WRSPMQB2
4/22/14
Description:
Product Code(s):
Equipment
Required
Associated
Documents:
Eng Approved:
Date:
Alt Approved:
Date:
DATE
INITIAL
4/22/14
rm
5/23/14
rm
Speco Technologies Confidential
Assembly Instruction
AI – D8WRSMPMQB2
D8WRSM, D16WRSM
TBD
#1 Size Phillips head drill, Flat head screwdriver,
3/16" hex head driver, ¼" hex head driver
REVISION HISTORY
REASON FOR CHANGE
New Document
•
Changed colors of power cable
AI- D8WRSPMQB2 Rev a
200 New Highway, Amityville NY 11701
Page 1 of 20
REV.
NC
a
Advertisement
Related Manuals for Speco D8WRSM
Summary of Contents for Speco D8WRSM
- Page 1 Product: D8WRSPMQB2 AI- D8WRSPMQB2 Rev a 4/22/14 Page 1 of 20 Assembly Instruction AI – D8WRSMPMQB2 Description: D8WRSM, D16WRSM Product Code(s): Equipment #1 Size Phillips head drill, Flat head screwdriver, Required 3/16” hex head driver, ¼” hex head driver Associated...
- Page 2 The holes will be drilled on the door hinge side of the wall mount and at the specific locations 5.25” and 6.00” from the base. Use a starter drill such as 1/8”. Final drill size for both holes is 5/16”. Speco Technologies Confidential 200 New Highway, Amityville NY 11701...
- Page 3 Connect the Lamp assembly and the sensor switch assembly to the chassis with the supplied hardware. Note that the switch assembly gets the conical washer as shown. Below are the 2 cable assemblies mounted to the chassis (inside). Speco Technologies Confidential 200 New Highway, Amityville NY 11701...
- Page 4 Solder this wire to the gold terminal post on the Lamp Cable led. Heat the shrink tubing with the heat gun. Add a cable anchor to the inside chassis as shown. Photo right, tie assemblies cable in a neat bundle and secure with a tywrap. Speco Technologies Confidential 200 New Highway, Amityville NY 11701...
- Page 5 Product: D8WRSPMQB2 AI- D8WRSPMQB2 Rev a 4/22/14 Page 5 of 20 The photo above shows the 2 cable assemblies in a bundle. Speco Technologies Confidential 200 New Highway, Amityville NY 11701...
-
Page 6: Pre-Assembly
(90272A081), two 2-56 nuts (90480A003) and two bumpers (9540K11). Place the bumper between the board and the plate. The nut should be on the plate. The wired side should be at the bottom of the plate near the tabs. Speco Technologies Confidential 200 New Highway, Amityville NY 11701... - Page 7 4) Connect the power board cable and the video cable to the monitor board 5) Release the ribbon from the back of the monitor and place the power connector through the hole in the WRSMPlate. Speco Technologies Confidential 200 New Highway, Amityville NY 11701...
- Page 8 9) Attach the ribbon to the monitor board by releasing the clip and inserting the ribbon. Be sure not to crease the ribbon. Once inserted lock in by pressing the clips back in. Speco Technologies Confidential 200 New Highway, Amityville NY 11701...
- Page 9 Product: D8WRSPMQB2 AI- D8WRSPMQB2 Rev a 4/22/14 Page 9 of 20 10) Group the cables and wire tie down using the open hole on the monitor board as shown below. Speco Technologies Confidential 200 New Highway, Amityville NY 11701...
-
Page 10: Section 3.0 - Main Assembly
Main Board 1) Place the WM Housing in front of you and tighten the nylon screw (93135A144) into the 3 pems which will not be utilized during the build. See below. Speco Technologies Confidential 200 New Highway, Amityville NY 11701... - Page 11 3) Lay the main board on the pem so they align with connectors facing the holes and lock down the corner with IR Board using the 1” Hex Standoff (93620A446), this must be done by hand tool. Speco Technologies Confidential 200 New Highway, Amityville NY 11701...
- Page 12 5) Obtain the IR Board, connect one end of the cable to the back of the IR board. Attach the IR Board to the standoff using a 6-32 screw (DVRWM632SCREW) and a 6-32 standoff 7/16” (93620A730) as shown below. Speco Technologies Confidential 200 New Highway, Amityville NY 11701...
- Page 13 HDD Connectors 8) Connect the SATA Combo connector to the HDD and the main board, then using a wire tie secure the wires. The IR Board cable does not get bundled. Speco Technologies Confidential 200 New Highway, Amityville NY 11701...
- Page 14 12) Attach the Video connector from the monitor board to the RCA to BNC connector and attach to the BNC Video output on the DVR. Zip tie the cable so it runs cleanly back up the connector toward the monitor. Speco Technologies Confidential 200 New Highway, Amityville NY 11701...
- Page 15 There is no polarity for this connection. Connect the 2 remaining black wires to the 6 column as shown. There is no polarity for this connection. Speco Technologies Confidential 200 New Highway, Amityville NY 11701...
- Page 16 Product: D8WRSPMQB2 AI- D8WRSPMQB2 Rev a 4/22/14 Page 16 of 20 Connect Power connector as shown Assembly complete Upgrade this unit with the following firmware: main_d8wrspb_speco_3.8.2_20131101.bin Speco Technologies Confidential 200 New Highway, Amityville NY 11701...
- Page 17 Install a formatted thumb drive in a USB terminal. Next: Press the red button that was installed and hold for 3 seconds or until the LED illuminates. An icon will appear on the screen. Speco Technologies Confidential 200 New Highway, Amityville NY 11701...
- Page 18 Click on the icon and and close the window. Verify the download with the thumbdrive installed on a PC or laptop by opening the DVR player and selecting the Ch1 file in the DVR folder. Speco Technologies Confidential 200 New Highway, Amityville NY 11701...
- Page 19 1. The plastic caps to the bottom openings 2. Lock to the housing door. 3. Sticker on the Door and Label of the unit. 4. Place the unit in a clear plastic bag prior to packaging. Finished Product: Speco Technologies Confidential 200 New Highway, Amityville NY 11701...
- Page 20 IR Board connector is seated to IR Board and Main Board. • Ribbon Connector properly connected to monitor and monitor board. • Wire tie is present and bundles cables together, not including IR cable. • Power splitter is properly connected. • Speco Technologies Confidential 200 New Highway, Amityville NY 11701...
Need help?
Do you have a question about the D8WRSM and is the answer not in the manual?
Questions and answers