D-Teg BRX Series User Manual
  1. Manuals
  2. Brands
  3. D-Teg Manuals
  4. DVR
  5. BRX Series
  6. User manual

D-Teg BRX Series User Manual

Micro dvr
Hide thumbs
Table of Contents

Advertisement

Quick Links

BRX
USER GUIDE
Models: BRX2004A & BRX2008A
VER 2.1.0
• Thank you for purchasing the BRX Micro DVR from D-TEG.
• Please ensure that you read and understand this USER GUIDE
and use it before connecting and installing this Recorder.
• Please store the USER GUIDE in an easily accessible location.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BRX Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for D-Teg BRX Series

Summary of Contents for D-Teg BRX Series

  • Page 1 USER GUIDE Models: BRX2004A & BRX2008A VER 2.1.0 • Thank you for purchasing the BRX Micro DVR from D-TEG. • Please ensure that you read and understand this USER GUIDE and use it before connecting and installing this Recorder. • Please store the USER GUIDE in an easily accessible location.

  • Page 3: Safety Advice

    SAFETY ADVICE CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Please make sure you follow the safety advice/instructions given in the user guide. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

  • Page 4: Gps Reception

    GPS Reception Activate the product in an area without large buildings to improve GPS reception. The commercial purpose GPS has the average range error of more than 15 meters and the range error could be more than 100 meters due to environmental conditions like buildings, roadside trees etc.
  • Page 5 CONTENTS Each BRX2004A/2008A order includes the following items. 1. Main unit 7. Mini USB Cable 8. USER GUIDE 2. GPS module with waterproof case 9. DVR Viewer CD 3. Camera input cable 4. Power cable 10. Keys, Screws 5. Car signal cable 11.
  • Page 6 INTRODUCTION FRONT ① ② ③ ⑧ ⑨ ⑤ ⑥ ⑦ ④ ① System Door Lock ② LED [POWER] : Green LED indicates power-on [REC] : Yellow LED indicates record-on [ALARM] : Red LED indicates Video loss or SSD/HDD failure. [LAN] : Yellow LED indicates network-on ③...
  • Page 7 INTRODUCTION FRONT ⑨ BUTTON [SER] : Searches the recorded data. [CH] : Changes the camera on display. (Camera 1 → Camera 2 → Camera 3 ->..->Camera 8 → Camera 1) [ESC] : Cancels or exits from the selected modes or menus. [MENU] Enters into the menu.
  • Page 8 INTRODUCTION REAR ④ ① ② ③ ⑤ ⑧ ⑦ ⑨ ⑩ ⑥ ① Power Connector Battery : Connects to the battery power in vehicle. ACC : Connects to the ignition power in vehicle. ② Car Signal Connector: left/right signals, brake, reverse, speed pulse signal ③...

  • Page 9: Connection Diagram

    CONNECTION DIAGRAM...

  • Page 10: Turning On The Power

    POWER ON 1. TURNING ON THE POWER ① Make sure that peripherals are properly connected. ② Switch「ON」the main power switch on the rear panel as below, Main power switch ③ Turn on the Removable HDD/SSD lock using key from [OFF] to [ON] as below, The front POWER LED will light up in green.

  • Page 11: Turning Off The Power

    POWER OFF 2. TURNING OFF THE POWER ① Turn off the Removable HDD/SSD lock using key from [ON] to [OFF] as below, The RECORD LED will be off immediately and the front POWER LED will be off in 15 seconds. [System shutdown pop-up window] ②...

  • Page 12: System Operation

    SYSTEM OPERATION LIVE DISPLAY Status icons: Video loss, Motion Detection, CAMERA TITLE Audio Record, Video Record Speed from GPS Speed from car pulse Storage Usage Current Date & Time Alarm in, Alarm out, G-sensor icons Press [CH] button to see a single channel display Press [Right] button to see 4 channel display Press [Left] button to see 8 channel display Default display layout can be set in Device menu of the DVR Viewer.
  • Page 13 SYSTEM OPERATION LIVE DISPLAY ICONS Video Loss, No Camera Motion Detection Audio Record Continuous Record (RED) Event Record (YELLOW) Detect Alarm in 1 Detect Alarm in 2 Detect Alarm in 3 Detect Alarm in 4 Detect Alarm in 5 Detect Alarm in 6 Detect Alarm in 7 Detect Alarm in 8 Activate Alarm out 1...
  • Page 14 STATUS To turn off/on the status icons, Press the [STA] button. Below are the different views you can toggle with the [STA] button, 1. [All Icons] 2. [Without Icons] 3. [Without Icons, Camera titles] 4. [Without all icons] This information page shows the current system information such as firmware version, GPS acceptance, Alarm In/Out, Car...

  • Page 15: Selecting A Menu Item

    MAIN MENU Press the [MENU] button on the front panel brings up the main menu below. The on-screen menus allow you to check the configuration. Only some settings can be changed here, please use provided DVR Viewer PC Software to set up all the features of BRX. All setup data is safe from power loss and stored in the internal flash memory of DVR.
  • Page 16 MAIN MENU CAMERA Brightness and Contrast of each channel can be configured in this menu. To change the Video or Camera title, please use the DVR Viewer on your PC. Press [ESC] button to return to the previous mode. SIGNAL Speed pulse type and pulse standard can be configured in this menu.
  • Page 17 MAIN MENU G-SENSOR G-sensor calibration can be configured in this menu. G-SENSOR(X) 0, 90, 180, 270 -(Y) 0, 90, 180, 270 -(Z) 0, 90, 180, 270 [Example- Standard Installation] FRONT (X axis): Front sides of BRX and car must be in line, facing the front side. LEFT (Y axis): Left side of BRX must be facing the left side of car and BRX must be horizontal, parallel with the ground.
  • Page 18 MAIN MENU DISPLAY This menu is to view/change the default display screen. To change which screen is your default display screen, please use the DVR Viewer on your PC. Press [ESC] button for returning to the previous mode. RECORD Recording conditions such as Frame Rate, Resolution and Image Quality can be changed. To change the Record set up, please use the DVR Viewer on your PC.
  • Page 19 MAIN MENU To change the Resolution, Quality, Pre-recording time, Post-recording time, please use the DVR Viewer on your PC. Change the channel and check the record set up per channel To change the Record Normal/Event, fps, audio on/off, please use the DVR Viewer on your PC.
  • Page 20 MAIN MENU SYSTEM DATE/TIME/LANGUAGE and NTSC/PAL can be configured in this menu. Press [ESC] button for returning to the previous mode. DATE/TIME/LANGUAGE System time, Date format, Time format, Time zone, DST, GPS Time Synchronize can be configured in this menu.

  • Page 21: Permission Management

    MAIN MENU PERMISSION MANAGEMENT DVR ID, USER ID can be changed here. To change the DVR ID, USER ID, please use the DVR Viewer on your PC. DATE/TIME/LANGUAGE HDD Format, HDD recovery, Firmware upgrade, Factory Default can be done. Video standard (NTSC/PAL) can be set here.

  • Page 22: Configuration Settings

    CONFIGURATION SETTINGS UPLOADING YOUR SETTINGS TO THE BRX The configuration file can be saved into a USB memory stick via DVR Viewer Software. Insert USB memory stick containing the configuration file (set operation condition) to USB port in BRX. It may take around 5~10 seconds until the USB stick is recognized. Then press and hold the [Fn] button &...

  • Page 23: Pc System Requirement

    SOFTWARE USER GUIDE BRX200A DVR Viewer Guide [PC SYSTEM REQUIREMENT] Recommended PC specifications for DVR Viewer software Windows XP, Windows Vista, Windows 7 Intel Core 2 Duo (2Ghz)or higher 1GB or higher VGA Memory 256MB or higher HDD Free space 120MB or higher Display 1,024 x 768 pixel/High Color(16bit) or higher...

  • Page 24: Installing Procedures

    INSTALLING PROCEDURES DVR Viewer software is on the provided CD. 1. Insert the CD into your PC and run [SETUP.EXE]. 2. Select the language and then follow the dialog box. 3. Continuously install EXt2Fsd driver. It’s necessary to read the removable HDD/SSD. 4.
  • Page 25 PC SOFTWARE & DVR VIEWER SETTINGS The “DVR Viewer” icon will be displayed on your desktop. Click to run DVR viewer. ※ NOTE: To Un-install the “DVR Viewer BRX2004A” Open the “Control Panel” Select [Remove Program] and remove [DVR Viewer BRX2004A] To set the DVR Viewer itself, Click the setting icon.
  • Page 26 DVR CONFIGURATION: SETTING FILE To set the DVR configuration, First, connect a USB memory stick into your PC’s USB slot. Run “DVR Viewer BRX2000A” Software and click the setting icon. setting And then click Machine config [NEW] Select your DVR model first, and then click OK. If you already have a DVR configuration in your memory stick, click [OPEN].
  • Page 27 DVR CONFIGURATION: DEVICES DEVICE Camera ON/OFF Select cameras connect. Camera Cam Title The camera title can be up to 10 characters. Brightness Adjust Brightness of camera Contrast Adjust Contrast of camera Display Default layout Select default display layout. If you set 2x2, when you turn on the DVR quad screen will be displayed.
  • Page 28 DVR CONFIGURATION: G-SENSOR CALIBRATION G-Sensor Calibration If you install FRONT (X axis): Front sides of BRX and car must be in line, facing the front side. LEFT (Y axis): Left side of BRX must be facing the left side of car and BRX must be horizontal, parallel with the ground.
  • Page 29 DVR CONFIGURATION: CALIBRATION OPTIONS F : Front RR : Rear Different installation 2 - BRX top is facing the ground. TOP : Top B : Bottom R : Right L : Left (X:180, Y:0, Z:0) (X:180, Y:0, Z:180) (X:180, Y:0, Z:90) (X:180, Y:0, Z:270) Different installation 3 Different installation 4...
  • Page 30 DVR CONFIGURATION: G-SENSOR LEVELS Set G-Sensor Trigger level [1(insensitive)~5(The most sensitive)] If G-sensor sensitivity value is high (5), it may be too sensitive, it will detect even a light impact or light turn. If G-sensor sensitivity value is a low setting (1), it might not detect a notable incident.
  • Page 31 DVR CONFIGURATION: RECORD SETTINGS RECORD Audio Record ON/OFF Video Type Select your Video Standard(Camera type.). This Video Standard(NTSC/PAL) is just for FPS calculation. This is different from your DVR video standard. To change your DVR video standard, set your video standard at service menu of DVR. Refer to page 21.
  • Page 32 DVR CONFIGURATION: RECORD SETTINGS CONT’D Remained FPS Show remained FPS / Total FPS Resolution D1: 720x480(NTSC), 720x576(PAL) HD1: 720x240(NTSC), 720x288(PAL) CIF: 360x240 (NTSC), 360x288(PAL) Quality Normal: Small file size, low picture quality. High: Super: Large file size, good picture quality. Event Pre-event-record time is 0~5sec.
  • Page 33 DVR CONFIGURATION: MOTION DETECTION EVENT Motion Detection To use motion detection as a Event, check the camera first. Sensitivity 1(Insensitive)~5(The most sensitive) Set Grid Default setting: All area is motion detecting area. To disable motion detect, click blocks and make it to black. Record CH Select motion event record channel Alarm out1...
  • Page 34 DVR CONFIGURATION SETTING Alarm Input To use Alarm In as a Event, check the alarm first. Title Set Alarm In title Type Set Alarm In Type Alarm In 1~4: Voltage ON / Voltage OFF. Alarm In 5~8: Normal Close / Normal Open Record CH Select Alarm record channel Alarm out1...
  • Page 35 DVR CONFIGURATION SETTING Signal Title Set Signal title Record CH Select Signal record channel Alarm out1 Set alarm out 1 duration from 0~∞ Alarm out2 Set alarm out 2 duration from 0~∞ Live out Set Live display channel Live out Set Live display duration.
  • Page 36 DVR CONFIGURATION: VEHICLE SPEED G-Sensor / Speed GPS Speed Set GPS speed, Exceeding this speed will trigger. Pulse Speed Set Car speed pulse speed, Exceeding this speed will trigger. Record CH Select which channel will record when speed i Alarm out1 Set alarm out 1 duration from 0~∞...
  • Page 37 DVR CONFIGURATION: VIDEO CHANNEL PRIORITY Live out Priority This menu is to set the default live display priority. 1 is the highest priority display channel on the live screen. 2x2_1 : quad mode (cam1~cam4) 2x2_2 : quad mode (cam5~cam8) : 8 split mode (cam1~cam8) If you set 2x2_1 as 1 and turn on the DVR, the first screen will be always quad (Cam1~Cam4) mode.
  • Page 38 DVR CONFIGURATION: SYSTEM SETTINGS SYSTEM Language Set your DVR language Date Format Set your DVR Date Format. Time Format Set your DVR Time Format Speed Format Set your DVR Speed Format Apply DST Set Daylight Saving Time Time Zone Set your Time zone Time Sync Set time synchronize time.
  • Page 39 Connecting Removable HDD/SSD to your PC 1. Connect Removable SSD/HDD to your PC through provided USB mini cable. 2. Run “DVR Viewer BRX2000A” 3. Click [HDD load] icon. [HDD load] icon 4. Select HDD [NOTE] Up to 4 removable HDD/SSD can be connected to a PC at the same time.
  • Page 40 Opening the Data Folder Use this button after you download the whole removable HDD data into a folder in your PC. If you copied all removable HDD files include folders into the [aaa] folder as below, click Open Data Folder button and then select [aaa] folder to open the data. select [aaa] folder And then click OK...

  • Page 41: Playback Screen

    Playback screen Camera title (Resolution) Date/Time Speed Pulse speed/Signal/Google map/Alarm In1~8 Playback control Slide Bar Buttons Playback can be controlled with the buttons in bottom. The slider helps for easy searching of the desired playback position or time. In case that the user wants to search the other date, click [Calendar Search] Button at the upper layer of screen.

  • Page 42: Playback Control Buttons

    Main buttons / Playback control buttons Main Buttons HDD Load Calendar Search Print Image File Load Event Search Backup Close Data Privacy Set Backup List View Information Save Jpg Setting Select Layout Save AVI About Playback control Buttons Before Reverse Pause Play Next...
  • Page 43 Select Display layout Click [Select Layout] button and then window for layout selection appears. [Select Layout] button Window for layout selection Click this icon for returning to the previous screen. [Select Layout] button To see 1 camera only, double-click the screen. Or right-click on screen and select camera Return to multi-screen mode, double click screen.
  • Page 44 Viewing GPS and G-Sensor Information Click [View Information] button during playback. [View Information] button BRX can record not only video & audio data of 8 Channels but also useful driving information of vehicles such as GPS position, speed, left/right signal, brake signal and speed pulse &...
  • Page 45 Google™ Maps Integration Click [Google map] button during playback. [Google map] button To see the route & position on the Google map, the GPS data should be recorded with video. To see the map, the PC must be connected to the Internet. Now here The playback position will be shown on the map with an arrow.
  • Page 46 Multi-Window Playback The Main DVR viewer, Information Window, and Google Maps Window can be displayed on the same monitor at the same time and their size can be adjusted individually. 3 different windows can work as an integrated analysis software, which improves the efficiency of the security/fleet management.

  • Page 47: Calendar Search

    Calendar Search Click [Calendar Search] button during playback to search the other date. [Calendar Search] button Dates containing recorded data are to be marked with box of Orange color. Once the selected date is clicked, the hours containing recorded data are marked with Orange color, too.

  • Page 48: Event Search

    Event Search Click [Event Search] button to quickly search for events only. [Calendar Search] button [Event Search] BRX can access to the data of G-Sensor Trigger, Car Signal Information, Alarm or speed with video/audio, which means that user can easily search and playback the classified data by the different conditions.

  • Page 49: Privacy Set

    Privacy Set The BRX can set up a Privacy region on each channel to protect the people/information from unnecessary disclosure to public. The set privacy region becomes blurred in case of back up the original data to JPG, AVI and export to any other report. Click [Privacy Set] button to set privacy region.
  • Page 50 Save JPG Files & Convert to AVI Pause the playback and click [Save Jpg] button to make a JPG file. [Save Jpg] button Pause the playback and click [Save AVI] button to make an AVI file. [Save AVI] button...

  • Page 51: Print Image

    Print Image Pause the playback and click [Print Image] button to print out. [Print Image] button Type in the Title [Print Title] & any comments [Comment] using the Keyboard.

  • Page 52: Data Backup

    Data Backup Click [Backup] button to backup the files to the PC. [Backup] button Type means a folder name. Need this to start backup. Type in the Memo Title & Memo using the Keyboard. And then set the Type (Folder name) and click start button.
  • Page 53 Backup List Search Click [Backup List] button to playback backup file. [Backup List] button Select Type to search. Under selected type, file list shows up with the information of time, DVR ID, USER ID. Select the required file and click [OK] Button.
  • Page 54 About Click [About] button to verify the product version and information. [About] button Click [HotKey] tap to check the hot key (simplified button) for the functions of DVR Viewer Software.

  • Page 55: Specifications

    Specifications...
  • Page 56 D-Teg America, LLC 600 Morse Ave., Unit A 877-601-9918 info@d-teg.com www.d-teg.us MADE IN KOREA...

This manual is also suitable for:

Brx2008aBrx2004a

Table of Contents