Bosch GEX 125-1 A Professional Original Instructions Manual page 7

Keep cutting tools sharp and clean. Properly main-
u
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in
u
accordance with these instructions, taking into ac-
count the working conditions and the work to be per-
formed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and
u
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
Service
Have your power tool serviced by a qualified repair
u
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Safety Warnings for Sander
Only use the power tool for dry sanding. Water entering
u
a power tool will increase the risk of electric shock.
Ensure that no persons are at risk due to flying sparks.
u
Remove combustible materials from the surrounding
area. Flying sparks are created when sanding metals.
Warning: Danger of fire! Avoid overheating the work-
u
piece and the sander. Always empty the dust collector
before taking a break from work. Sanding dust in the
dust bag, microfilter, paper bag (or in the filter bag or va-
cuum cleaner filter) can spontaneously combust under
certain conditions, for example if flying sparks are cre-
ated when sanding metals. This risk is increased if the
sanding dust is mixed with paint or polyurethane residue
or with other chemical substances and if the workpiece is
hot as a result of prolonged work.
Clean the air vents on your power tool regularly. The
u
motor's fan will draw the dust inside the housing and ex-
cessive accumulation of powdered metal may cause elec-
trical hazards.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
Technical Data
Random orbit sanders
Article number
Orbital stroke rate preselection
Rated power input
No-load speed n
0
No-load orbital stroke rate
Bosch Power Tools
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Always wait until the power tool has come to a com-
u
plete stop before placing it down.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Product description and
specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for dry sanding of wood, plastic,
metal, filler and varnished surfaces.
Power tools with electronic control are also suitable for pol-
ishing.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) On/off switch
(2) Orbital stroke rate preselection thumbwheel
(GEX 125-1 AE)
(3) Complete dust box (Microfilter system)
(4) Handle (insulated gripping surface)
(5) Sanding pad
A)
(6) Sanding sheet
(7) Screws for sanding pad
(8) Extraction outlet
(9) Filter element (Microfilter system)
(10) Dust extraction hose
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
GEX 125-1 A
Professional
3 601 C87 0..
W 250
rpm 12,000
rpm 24,000
English | 7
A)
GEX 125-1 AE
Professional
3 601 C87 5..
– ●
250
7500–12000
15,000–24,000
1 609 92A 4AJ | (24.05.2018)