Subscribe to Our Youtube Channel
Related Manuals for Accutech LS2400
Summary of Contents for Accutech LS2400
- Page 1 LS2400 User Manual 800-356-2671 | Accutech | www.AccutechSecurity.com Version 1.00...
- Page 2 FCC ID/DOC for the LS2400T Controller: FCC ID: JM7-HWHY-662110 IC: 2683A-662110 Compliance Statement (Part 15.19) This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2.
-
Page 3: Table Of Contents
Contents Chapter 1: LS2400 System Alarms How Accutech Systems Work Addressing Alarms Escorting Chapter 2: Tags Tag barcodes Visual Pulse LED Attaching Tags Tag and Band Maintenance Chapter 3: The S-TAD Powering the S-TAD On/Off Unlocking the S-TAD Activating/Deactivating Tags... -
Page 5: Chapter 1: Ls2400 System
User Manual Chapter 1: LS2400 System IMPORTANT No Security System can replace human vigilance. Creating a safe environment requires the combined efforts of nursing, physicians, security, and patients. Global policies, procedures, and processes on patient care should be discussed and disseminated. Education, communication, and coordination are key. - Page 7 Escorting flash strobe lights The function of the LS2400 System is to alert trigger visual displays facility personnel of the possible egress of a Virtually any hallway, doorway, stairwell, or monitored resident. elevator can be made to sense a Tag and then...
-
Page 8: Alarms
If a Tag enters a monitored door zone with or Tamper without a Magnetic Lock(s) and the door is already open (or is opened while the Tag is in The LS2400 System cover panel has been the zone), the LS2400 System will go into tampered, removed, or obstructed. alarm. -
Page 9: Addressing Alarms
1-3 The LS2400 System User Manual Loiter Hallway zones An optional Loiter function is available to alert Egress staff personnel if a Tag is lingering in a If a Tag enters a monitored hallway zone, the monitored zone. The time setting is adjustable... - Page 10 Addressing Tamper alarms c. Is there is a misplaced Tag in A Loiter alarm occurs when the LS2400 cover the zone? panel has been tampered, removed, or 2. After removing the cause, the system obstructed.
-
Page 11: Escorting
Escorting To escort Tags through a monitored zone, use the following instructions: DISCLAIMER: 1. Enter a valid code into the zone’s The following instructions are intended as a Keypad. This will invoke the Keypad’s guidance document only. Each facility should Escort function. -
Page 13: Chapter 2: Tags
User Manual Chapter 2: Tags... - Page 15 Tags also contain a visual pulse LED to indicate when they are active. Tags are activated/deactivated with an S-TAD unit. The LS2400 System Tag band is made of nylon-reinforced vinyl with nylon mesh. The band is designed to resist tearing caused by pulling or chewing on the band.
-
Page 16: Tag Barcodes
Tags 2-2 User Manual Tag barcodes Visual Pulse LED Tag barcodes (Figure 2.3) contain a Tag’s The Visual Pulse LED indicates the Tag’s manufacturing history. current mode ( see Table 2.1 Table 2.1 Visual Pulse LED status LED Light Pattern Tag LED Status LT, SB Tags None... -
Page 17: Attaching Tags
. Figure 2.4: LT Tag with band 1. For LT Tags, with the snaps pointing in the same direction as the Accutech logo, slide the plastic band through the Slot. see Figure 2.4 2. Adjust the band length to the nearest accommodating hole for a comfortable fit around the patient’s extremity. -
Page 18: Tag And Band Maintenance
Testing Tags Wipe down with 3% hydrogen peroxide with water solution then Accutech Tags operate by internal battery. rinse with a water-dampened cloth Over the course of normal operation, Tags towel and wipe dry. (wipe only, eventually lose battery power and the Tags DO NOT soak, submerge or place will need to be replaced. -
Page 19: Chapter 3: The S-Tad
User Manual Chapter 3: The S-TAD... -
Page 21: Powering The S-Tad On/Off
The Power/Clear LED illuminates (solid green with wink). The S-TAD (Secure Tag Activator/Deactivator) is used to check the functionality of an Accutech 2. Using the number keypad, enter a valid Tag. Accutech Tags operate by internal battery. 4-digit user code. Entering a valid code... - Page 22 3-2 The S-TAD User Manual Activating/Deactivating Tags 6. The S-TAD will still detect active Tags and Low Battery conditions in the area The S-TAD can activate and deactivate Tags even after the Enter LED extinguishes. preserving Tag battery life and preventing However, you will have to unlock the S- nuisance alarms.
- Page 23 User Manual The S-TAD 3-3 Programming Mode Set Unlock Timeout: 1. Enter Programming Mode While in programming mode, the Enter button’s 2. Press: 5, Enter, 5, Enter LED winks quickly. In addition, the Enter button LED will also indicate if a programming step (3 slow green flashes) was completed successfully.
- Page 24 3-4 The S-TAD User Manual To add a user code: Summary of LEDs 1. Enter Programming Mode WAIT LED 2. Press: 2, Enter, 2, Enter Tag is in the process of being (3 slow green flashes) turned on or off or during S-TAD unlocking.
- Page 25 User Manual The S-TAD 3-5 Cleaning and Care The S-TAD should be cleaned periodically using antibacterial wipes (wipe, do not soak). Do not use any abrasive cleaners or cloths. When not in use the S-TAD should be stored in a clean and dry environment. The S-TAD requires a 9-volt lithium battery to operate.
Need help?
Do you have a question about the LS2400 and is the answer not in the manual?
Questions and answers