Summary of Contents for Dekolink MW-FBDA-PCS-xxx-50W
Page 1
Fiber-optic Repeater System (MW-FBDA-PCS-xxx-50W) & FiberopticBase Interface Unit (FBIU) Dekolink Wireless Proprietary and Confidential Information. Copying, Distribution, and Disclosure are prohibited without Express Authorization from Dekolink Wireless Company. This document is protected by all applicable copyright laws. FO-50W SYS Page 1 of 12...
Dekolink WIRELESS Ltd. 16 Bazel St. Qiryat-Arieh Petah-Tikva, Israel, 49510 Tel- 972-3-9180-180 Fax-972-3- 9180 e-mail: marketing@dekolink.com www.dekolink.com 1. OVERVIEW: The Fiber optic repeater system is an excellent solution for BTS coverage extension by means of Fiber optic link and remote high power RF head.
Dekolink WIRELESS Ltd. 16 Bazel St. Qiryat-Arieh Petah-Tikva, Israel, 49510 Tel- 972-3-9180-180 Fax-972-3- 9180 e-mail: marketing@dekolink.com www.dekolink.com 1.2 FBDA The FBDA is installed near the area to be covered and is connected to the mobile antenna. A Fiberoptic transceiver converts the Downlink optical signals to RF signals and the uplink RF signals to optical signals.
Dekolink WIRELESS Ltd. 16 Bazel St. Qiryat-Arieh Petah-Tikva, Israel, 49510 Tel- 972-3-9180-180 Fax-972-3- 9180 e-mail: marketing@dekolink.com www.dekolink.com 2. SUBSYSTEM DESCRIPTION: 2.1 FBDA Refer installation operation instructions MW-FBDA-PCS-xxx-50W 2.2 FBIU The FBIU is the BTS interface of the system. It contains one Fiberoptic transceiver and attenuators for uplink and downlink paths and power supply.
Dekolink WIRELESS Ltd. 16 Bazel St. Qiryat-Arieh Petah-Tikva, Israel, 49510 Tel- 972-3-9180-180 Fax-972-3- 9180 e-mail: marketing@dekolink.com www.dekolink.com SYSTEM SPECIFICATIONS: 3.1 RF SPECIFICATIONS (optical loss adjusted to 0dBm, all attenuators 30 dB) Frequency Range Uplink (RX) Downlink (TX) Per system Per system Passband Gain @ min attenuation 16 dB Nom.
Dekolink WIRELESS Ltd. 16 Bazel St. Qiryat-Arieh Petah-Tikva, Israel, 49510 Tel- 972-3-9180-180 Fax-972-3- 9180 e-mail: marketing@dekolink.com www.dekolink.com 3.2 FBDA ALARM SPECIFICATIONS RemoteFault Alarm is sent on the serial data link of the FO transmitter Indication to FBIU (Summarized alarm) Fault List :...
Dekolink WIRELESS Ltd. 16 Bazel St. Qiryat-Arieh Petah-Tikva, Israel, 49510 Tel- 972-3-9180-180 Fax-972-3- 9180 e-mail: marketing@dekolink.com www.dekolink.com 4. INSTALLATION PROCEDURE 4.1 Fiber Optic Link Assembly:(both FBDA and FBIU) 4.1.1 Insert main optical fiber trough the Fiber In/out hole on the FBDA panel and connect it to the Optical In/out connector on the Fiberoptic transceiver.
Dekolink WIRELESS Ltd. 16 Bazel St. Qiryat-Arieh Petah-Tikva, Israel, 49510 Tel- 972-3-9180-180 Fax-972-3- 9180 e-mail: marketing@dekolink.com www.dekolink.com 4.4 System assembly: 4.4.1 Connect BTS Tx to Tx antenna port on FBIU. (Another 10dB attenuator can be connected to the RF IN port of the Fiberoptic transceiver in the FBIU and the Rotary Attenuator on the FBIU front panel adjusted slightly for system performance optimization).
Dekolink has been advised of the possibility of such damage. Some states do not allow the exclusion or limitation of incidental or consequential damages so these limitations may not apply under certain circumstances.