Subscribe to Our Youtube Channel
Related Manuals for GreenTec LRS 1601
Summary of Contents for GreenTec LRS 1601
- Page 1 Page 1 af 20 LRS 1601 QUADSAW Handbook & Spareparts 5. Edition March 2016 ©GreenTec Machinery Limited...
-
Page 2: Table Of Contents
Page 2 af 20 Contents Contents Introduction ........................3 Important ........................4 Mounting the Quadsaw ....................5 Operation / Introduction ....................6 Maintenance ........................6 Driving recommendations ..................... 6 Belt diagram ........................7 Correct belt adjustment ....................8 Technical data and description of working tool ............9 Safety ........................... -
Page 3: Introduction
The content also makes you familiar with connectivity, use, care and maintenance. And then it helps to prevent injuries. We hope, you are happy with your new LRS 1601 Quadsaw. Best regards: John Christensen... -
Page 4: Important
Please, fill out the following information. It is practical information that is useable when ordering spare parts. …………………………………………………… Serial number: …………………………………………………… Delivery date: …………………………………………………… Dealer name : …………………………………………………… Address: …………………………………………………… …………………………………………………… Tel. / Fax No.: GreenTec A/S Merkurvej 25 Dk-6000 Kolding Tel: +45 7555 3644 Fax: +45 7555 4243 info@greentec.eu E-mail: www.greentec.eu Http:... -
Page 5: Mounting The Quadsaw
Page 5 af 20 Mounting the Quadsaw The blade is mounted, so the direction of rotation of the saw goes down (Fig. 1). Saw is mounted in such a way, that the blade runs straight in the driving direction (Fig. 2). ... -
Page 6: Operation / Introduction
Page 6 af 20 Operation / Introduction The Quadsaw is used for cutting branches and trees up to a max. diameter of 100 mm without the branches being torn. Branches with a diameter over 70 mm, must be cut one of the time. Vertical cutting is allowed up to a 45 degree angle. -
Page 7: Belt Diagram
BEWARE!! The tension has now changed. The short belts is tightened to 550 Nm, the long belts are tightened to 650 Nm. Contact GreenTec´s After Sales Department if you have any questions. We might help you with a piece of good advice. -
Page 8: Correct Belt Adjustment
Page 8 af 20 Correct belt adjustment See also "Belt Diagram" for more information. NOTE!! After adjusting, turn the blades some rounds and then control again. Belt measure ”Optikrik II” Recommended tools: 17 & 19 mm 17 & 19 mm Ring/fork wrench Ratchet with short extension Gloves Loosen bolts. -
Page 9: Technical Data And Description Of Working Tool
The Quadsaw is supplied with a special bracket enabling mounting on various vehicles / ma- chines. The drive belt is like the supporting part on the carrying frame entirely covered. LRS 1601 Working width 1600 mm 2600 – 2700... -
Page 10: Safety
Page 10 af 20 Safety Never operate the machine with other people present, as it is possible for debris to be thrown from the saw blades in all directions. Always ensure all cab safety guards are in place and all tractor windows are closed. Newer al- low an inexperienced person to operate the machine without supervision. -
Page 11: Main Frame 1
Page 11 af 20 Main Frame PRE Jan. 2012... -
Page 12: Main Frame 2
Page 12 af 20 Main frame PRE Jan. 2012 Item Qty. Part no. Description 160100.0 Body See section "Knife Axle" See section "Belt-box" 160101.0 160102.0 Skid 160129.0 160173.0 Construction 160168.0 Backstop for blade 200163.0 Allen screws 8x10 mm 12.9 200104.0 Bolt 10x20 mm 160112.0 Branch deflector... - Page 13 Page 13 af 20 Main frame POST Jan. 2012...
- Page 14 Page 14 af 20 Main frame POST Jan. 2012 Item Qty. Part no. Description 160100.0 Body See section "Knife Axle" See section "Belt-box" 160101.0 160129.0 160173.0 Construction 160168.0 Backstop for blade 200163.0 Allen screws 8x10 mm 12.9 200104.0 Bolt 10x20 mm 2770421 Bolt 127B102...
-
Page 15: Belt Tensioner Box 1
Page 15 af 20 Belt tensioner box 1... -
Page 16: Belt Tensioner Box 2
Page 16 af 20 Belt tensioner box 2 Item Qty. Part no. Description 160128.0 Adjustment Box 200131.0 Bearing cpl. 200130.0 Motor 17 cc with "Item 28-30" 200160.0 Sealkit for Bondioli motor 200160.A Sealkit for Danfoss motor 160126.0 Belt pulley 105 mm 160124.0 Roll 160171.0... -
Page 17: Knife Shaft 1
Page 17 af 20 Knife shaft 1... -
Page 18: Knife Shaft 2
Page 18 af 20 Knife shaft 2 Item *Qty. Part no. Description 160164.0 Bearing 160122.0 Pulley 90 mm 160120.0 Bearing 160114.0 Mounting plate outer 160111.0 Saw blade 160115.0 Mounting plate inner 160121.0 Locking ring 12912080251 Allen screw 127B102 Spring washer 10 mm 160119.0 Locking ring 160130.0... -
Page 19: Stickers
Page 19 af 20 Stickers Item Qty. Part no. Beskrivelse LRS1601KITS Sticker Kit... -
Page 20: Noise Measuring
Page 20 af 20 Noise measuring Noise measuring has been made on the machine during normal working conditions at GreenTec A/S in Denmark, with a Elma 1350B Noise measurer, ICE 651 type II. The energy A-weighted Sound pressure is lower than 85 dB (A).
Need help?
Do you have a question about the LRS 1601 and is the answer not in the manual?
Questions and answers