Table of Contents
Advertisement
Quick Links
INTRODUCTION
The Multi-Zone remote control and receiver combo for RGB strip lights uses the most advanced RF wireless transmission technology.
The system consists of two parts: the handheld remote control and the in-line receiver.
The remote control can be synced with multiple receivers in up to 10 separate zones, and these zones can be controlled either separately or all at
once. Featuring 18 built-in changing modes, the remote control allows you to pause on one color, cycle through a variety of colors, create and
memorize themes, and/or alter the light intensity (brightness).
SAFETY AND WARNINGS
•
Install in accordance with the National Electric Code, and local regulations.
•
This product should be installed and serviced by a qualified electrician.
•
Do not connect directly to high voltage 120V AC power.
•
This product is rated for indoor installation and is not protected against moisture.
•
Proper heat dissipation will prolong the working lifespan of this product. Install in a well ventilated area.
•
Only install compatible LED drivers and fixtures. Contact Technical Support or visit the product page for compatible accessories.
•
Ensure applicable wire is installed between driver, fixture, and any controls in between. When choosing wire, factor in voltage drop, amperage
rating, and type (in-wall rated, wet location rated, etc). Inadequate wire installation could overheat wires and cause fire.
•
Utilize the wiring diagrams in this installation guide for basic setups.
I
2
4
5
7
8
*
I0
MI
M2
R G B- M Z- COMBO
RGB COLOR CHANGING MULTI-ZONE
LED Remote Control & Receiver
Touch Adjustable Color Circle
Sync Status Indicator Light
Mode Adjust
(18 preset modes)
Speed Adjust
Brightness Adjust
(Keep pressing to adjust brightness
continuously)
3
6
Zone Selection Buttons
9
Pause Button
On/Off Button
Memory Buttons
(press for 3 seconds to save the current
settings for future recall
support@FlexfireLEDs.com
REMOTE CONTROL
Details
SKU:
Working Voltage:
Working Frequency:
PWM Frequency:
Max. Signal Range:
Working Temp:
Dimensions:
Weight:
Warranty:
925-273-9080 opt 2
RGB Multi-Zone Combo
RGB-MZ-CTRL
5V (Built-in lithium battery)
2.4GHz
2000Hz
98ft (30m)
-22°F ~ 131°F (-30°C ~ 55°C)
H: 5 3/4" (146mm) W: 2 1/4" (56mm)
D: 7/8" (22mm)*
7oz (200g)
5 years
*Comes with a wall mount for easy storage
User Guide
1
page
V.2018.11.01
Advertisement
Table of Contents
Related Manuals for Flexfire LEDs RGB-MZ-RCVR
Summary of Contents for Flexfire LEDs RGB-MZ-RCVR
-
Page 1: User Guide
RGB Multi-Zone Combo User Guide RGB COLOR CHANGING MULTI-ZONE LED Remote Control & Receiver INTRODUCTION The Multi-Zone remote control and receiver combo for RGB strip lights uses the most advanced RF wireless transmission technology. The system consists of two parts: the handheld remote control and the in-line receiver. The remote control can be synced with multiple receivers in up to 10 separate zones, and these zones can be controlled either separately or all at once. - Page 2 Mode Button Speed Button Brightness Button Green Pause Button Details SKU: Working Temp: RGB-MZ-RCVR -22°F ~ 131°F (-30°C ~ 55°C) Input Voltage: Dimensions: 12V-24V DC H: 8 1/4” (211mm) W: 1 5/8“ (40mm) D: 1 3/16” (30mm) Max Current Load:...
-
Page 3: Installation
User Guide • RGB Multi-Zone Combo INSTALLATION Always pre-test your LED setup prior to permanent installation. This will ensure all components work correctly. Be sure to check the amperage rating of the LED strip you’ve purchased so the receiver isn’t overloaded (max 5 amps per channel). Turn off the main AC breaker for the line you’ll be using before installing your low voltage power supply. -
Page 4: Additional Features
User Guide • RGB Multi-Zone Combo *Long Beep* Press and hold the power button on the receiver, you will hear a short beep after about 3 seconds, continue pressing the power button and press the number on the remote you wish to assign to that receiver (1-10) simultaneously. The Sync Status Indicator light will flash green 3 times. The remote is synced. -
Page 5: Preset Modes
User Guide • RGB Multi-Zone Combo * Z z Z z Z * press to turn on Turn On Inactive Receivers Preset Modes When a receiver has been inactive and you wish to turn it on without tuning all This remote comes with 18 preset modes which you can scroll through from the other zones on/off... -
Page 6: Remote Control Charging
User Guide • RGB Multi-Zone Combo REMOTE CONTROL CHARGING To charge the remote control, connect the mini USB cable to the remote and the opposite end of the cable to a regular USB port (computer or USB charger). The LED indicator on the remote will flash to show that the remote is charging. If the remote is turned off, however, the indicator will not flash. When the battery is fully charged, the LED light will remain static. -
Page 7: Troubleshooting
User Guide • RGB Multi-Zone Combo TROUBLESHOOTING - If your lights are not turning on or ickering: • Make sure the polarity of the power supply wires match the polarity of the terminals on the Power Input Terminal. • If the polarity from the power supply matches the Power Input Terminals, check the polarity on the Power Output side. Make sure you have matched the +, R, G and B markings on the LED strip to the channels on the receiver. - Page 8 User Guide • RGB Multi-Zone Combo Flexfire LEDs will NOT provide replacement items before the original items have been returned, tested, and deemed faulty. If you need a replace- ment item while the return process is taking place, then you can repurchase that item. Once the testing process is complete and assuming the product is faulty, a refund will be issued for the purchase price of the product.