Flexfire LEDs RGB-MZ-COMBO Installation Manual

I NSTA LLAT I ON G U I D E
S AF E T Y & WARNING S
•
Install in accordance with the National Electric Code, and local regulations.
•
This product should be installed and serviced by a qualified electrician.
• Do not connect directly to high voltage 120V AC power.
• This product is rated for indoor installation and is not protected against
moisture.
•
Proper heat dissipation will prolong the working lifespan of this product.
Install in a well-ventilated area.
Remote
Input Voltage
Working Current
Working Frequency
Transmitting Distance
MODE SPEED BRT
MODE SPEED BRT
I 2 3
Remote Option
4 5 6
7 8
PLAY
Battery Capacity
Standby Time
Normal Usage Time
Dimension
Weight (G.W)
I NSTAL L ATION
Always pre-test your LED light assembly prior to permanent installation. This will ensure all components are being joined properly and work correctly. Be sure to
check the amperage rating of RGB LED fixture you choose to install so the RGB Zone Receiver is not overloaded (Max 5A*3, 5A per channel). See installation
diagrams on the back of this page for sample installations.
1.
Turn off 120V AC power at the main breaker prior to installation.
2.
Connect your compatible driver to the Zone Receiver by attaching the negative output lead of your driver to the negative (DC-) input terminal of the
receiver, and positive output lead of your driver to the positive (DC+) input terminal of the receiver. If powering with a plug-in adapter, use a DC Splice Cable
to hard-wire the adapter to the receiver.
3.
To install an RGB LED fixture, connect the red lead to the negative (R) terminal; the green lead to the negative (G) terminal;
& the blue lead to the negative (B) terminal of the Zone Receiver. Connect the remaining positive lead to the positive (+) terminal of the receiver.
4.
Install additional components/accessories. Once complete, turn on 120V AC power.
C ha rg i ng th e Zo ne Re mo te
•
A flashing red indicator light on the Zone Remote implies a low battery.
•
To charge the Zone Remote, connect the included USB 2.0A/Mini-B cable to the remote and to any USB compatible computer or mobile charger with a USB
port (not included).
•
Press the power button on the Zone Remote and a blue indicator light will flash continuously to indicate charging. Once the indicator light turns green,
charging is complete.
P ai ri ng th e Zo ne R emo te wi th a Z o n e R e ceiv e r
The Zone Remote can control up to 8 different Zone Receivers. Only one remote can be paired to each receiver. To pair the Zone Remote
with a Zone Receiver:
1.
Turn on the Remote and Receiver by pressing the power button on each device.
2.
Next, press and hold the power button on the Receiver for 3 seconds until you hear a short beep, and continue to hold. Once the Receiver short
beeps immediately hold down a zone number of your choice (1-8) on the Remote. Ensure to continue holding the power button on the Receiver
after it beeps, and then simultaneously choose a zone on the Remote.
3.
To indicate pairing, the Receiver will long beep and a green indicator light will flash 3 times on the Remote.
Page 1 of 3
Before you begin, read all warnings and installation instructions thoroughly.
5 (Built-in Lithium battery)
DC V
≤30mA
2.4 GHZ
100 ft / 30m
Sync or zone control (8 zones)
1000m
Ah
≤6 months
30 days
5.7 × 2.2 × 0.8 in. ( x x )
L W H
7 oz
RGB Multi-Zone Combo
12v 24v
•
Only install compatible LED drivers and fixtures. Contact technical
support or visit the product page for compatible products.
•
Ensure applicable wire is installed between driver, fixture, and any
controls in between. When choosing wire, factor in voltage drop,
amperage rating, and type (in-wall rated, wet location rated, etc.).
Inadequate wire installation could overheat wires, and cause fire.
• Utilize the wiring diagrams in this installation guide for basic installations.
Receiver
Input Voltage
Max Current Load
Max Output Power
Change Mode
Control Button
Operating Temperature
Ambient Temperature
Dimension
Weight (G.W)
12-24
V DC
5 ×3 Max 15A
A CH
180 /360 (12 / 24 )
W W V V
18 modes
8 touch buttons
-22° - 131°
F
-4° - 104°
F
8.3 × 1.5 × 1.2 in. ( x x )
L W H
6.4 oz
V.2017.07.17