Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Pro'sKit Manuals
  4. Test Equipment
  5. 8PK-4103IN
  6. Manual

Pro'sKit 8PK-4103IN Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
高壓絕緣測試器
8PK-4103IN
操作說明書

Advertisement

loading

Related Manuals for Pro'sKit 8PK-4103IN

Summary of Contents for Pro'sKit 8PK-4103IN

  • Page 1 高壓絕緣測試器 8PK-4103IN 操作說明書...
  • Page 2 • 安全注意須知： 1. 本表須由受過絕緣測量訓練的人員使用。 2. 操作人員應按照程序進行，以免機體和人員受損。 3. 被測物不能有電源存在，測試之前，應檢查表體、測試線有無破損或 不良狀況，否則將導致危險。 4. 測試進行中，不可接觸表體或測試棒的金屬部份。 • 工作環境範圍： 1. 室內室外均可使用 2. 絕緣等級：CAT. III 3. 污染等級：第二級 4. 高度在海拔2000公尺以下 5. 最大相對濕度：80﹪ 6. 工作溫度：0°C~40°C • 國際電器符號： 電錶全部受雙層絕緣或補強絕緣保護 警告!!電擊危險 小心!使用前請參考說明書 • 供電機維護、工業設備、PC板、電纜、變壓器、配電盤、發電機..等 之高壓絕緣測試之用。...
  • Page 3 • 特點： 1. 使用寬廣型液晶顯示器(LCD) 2. 具有四檔量測電壓 0.5kV、1kV、2.5kV、5kV 3. 自動換檔，並且顯示出動作指示 4. 具有類比刻劃顯示電壓高低 5. 具有量測計時功能 6. 通過歐洲安全規範檢驗，獲貼"CE"標示 7. 具多種量測電壓選擇 8. 超柔軟測試棒，保證不斷線 9. 利用微處理器(Microprocessor)控制系統 10. 內置式大型積體電路保護裝置，有效降低表面泄漏電流引起的誤差 11. 具有450V AC以上電壓自動偵測及警告設計 12. 交流電壓警告裝置 13. 自動關機 14. 低功率損耗，省電 15. 自動斷電省電模式 16. 具限流功能 17. 有蜂鳴器發聲作用 18. 使用直流電池驅動 19.
  • Page 4 • 接線方式： 如果測試線未搭接綠色接地端子(GUARD)，被測體表面會造成漏電電流 產生，量測所得數值將不穩定，造成誤差，如下圖: 絕源體 黑色端子連接處 外皮 紅色端子連接處 芯線 被覆體 如果測試線有搭接綠色接地端子(GUARD)，被測體表面不致有漏電電流 產生，可以量測精確的數值，如下圖: 綠色端子連接處 黑色端子連接處 絕源體 外皮 紅色端子連接處 芯線 被覆體...
  • Page 5 • 儀表板面圖示： MODE 8PK-4103IN INSULATION TESTER 開始與停止測試按鈕 5kV選擇按鈕 2.5kV選擇按鈕 1kV選擇按鈕 500V選擇按鈕 液晶顯示器(LCD)
  • Page 6 • 量測方法： 1. 綠色接地線插入紅色測試線所附的綠色插座內，然後按照測線顏色， 前端插入表體相同顏色的極插座內。(紅色-LINE 綠色-GUARD 黑色- EARTH) 2. 測試線按照上蓋內面圖示，連接被測物 Select. Test 3. 按下ON/TEST鍵，顯示 字樣 2.5KV,1KV,or 500V 4. 進行選擇所需要的量測電壓，如按下500V鍵，顯示 字樣 500V 30000MΩ Selected Connect Leads..5. 字樣暫停時間很短，按著顯示 字樣 Testing for Live 6. 按下ON/TEST進行測試 (1)如果出現 ,表現出現異狀必須進行檢 LIVE WARNING CIRCUIT LIVE!!! 查有無ACV電源或修理 R=1253.0MΩ...
  • Page 7 R=1253.0MΩ85.2s 7. 停止測試時，顯示 HOLD 500V 8. 如果未再進行測試，約5分鐘蜂鳴器Bi一長聲之後，即自動關機 9. 需要再進行測試，重新按照3-7動作進行 • 電池更換： 1. 時機：當顯示器上出現"Replace Battery"字樣，即顯示電力不足，需 要更換電池 2. 方法： (1) 取下所有測試線 (2) 打開底部電池蓋，換入1.5V電池8顆，並注意極性 (3) 重新蓋上電池蓋、鎖住...

  • Page 8: Safety Precautions

    1.Safety Precautions Electricity can cause severe injuries even with low voltages or currents. Therefore it is extremely important that you read the following information before using your digital insulation tester. 1.1 This instrument must only be used and operated by a competent trained person and in strict accordance with the instructions.
  • Page 9 1.6 Your digital insulation tester has been designed with your safety in mind. However, no design can completely protect against incorrect use. Electrical circuits can be dangerous and/or lethal when a lack of caution or poor safety practice is used. Use caution in the presence of voltage above 24V as this poses a shock hazard.
  • Page 10 2.Models 2.1 8PK-4103 IN - Four voltages ( 500V, 1KV, 2.5KV and 5KV ) - Auto-ranging and menu-driven - A bar-graph which displays the voltage decay during the discharge of the tested circuit and the voltage stressing the insulation while the test is in progress.
  • Page 11 3. Features • 2 Lines x 16 Characters large L.C.D. • Four insulation test voltage. (1)500V DC - 25G (2)1000V DC - 50G (3)2500V DC - 125G (4)5000V DC - 250G • Insulation resistance auto-ranging on all ranges. • ENER-SAVE TM . •...

  • Page 12: Specifications

    4. Connections EARTH GUARD LINE CABLE CORE INSULATION COVERING OUTER SHEATHING 5. Specifications Test Voltage 500V DC 1kV DC 2.5kV DC 5kV DC Measuring 125G 250G Range Auto Ranging Accuracy 5% ±2 Digits Power 8 x 1.5V Alkaline Battery...

  • Page 13: Instrument Layout

    6. Instrument Layout 1- On switch. Test button switch. ENER-SAVE TM function switch. 2- 5000V test selection button. 3- 2500V test selection button. 4- 1000V test selection button. 5- 500V test selection button. 6- ENER-SAVE TM Intelligent L.C.D. GUARD LINE EARTH MICROPROCESSOR CONTROLLED AUTO RANGING...
  • Page 14 7. Functions 7.1 Power-On To switch the instrument on, press the "ON" button (1). The L.C.D. will display the Model. Then follow interactive instructions on L.C.D. 7.2 Auto-Off. The Auto-off is annunciated by a one-second beep. The Auto-off timer is automatically enabled. LIVE WARNING MESSAGE / BEEPER To clear Live Warning Message / Beeper Remove leads from circuit under test and push...
  • Page 15 7.3 Insulation resistance measurement @ 5kV DC: To select 5kV DC test voltage, press 5kV button (2) 7.4 Insulation resistance measurement @ 2.5kV DC: To select 2.5kV DC test voltage, press 2.5kV button (3) 7.5 Insulation resistance measurement @ 1kV DC: To select 1kV DC test voltage, press 1kV button (4) 7.6 Insulation resistance measurement @ 500V DC: To select 500V DC test voltage, press 500V button (5)
  • Page 16 7.8 Voltage Output Bar-Graph. The bar-graph displays the voltage present on the leads. It also displays the voltage charging a cable or capacitive system under test and displays the decay during the automatic capacitive discharge of the system under test. 7.9 Auto-Low Resistance Detect.
  • Page 17 7.13Auto Live / Voltage Warning. Should the leads be placed onto a live system before starting the test, a warning beeper will be automatically activated and, the instrument will display "Live Warning ..Circuit Live .."message. Allow the instrument to discharge the circuit ( in the case of capacitive system ) or make sure that the circuit under test is not live.
  • Page 18 8. Preparation for Measurement Before testing always check the following: - At power "ON", read the display to make sure the "Replace Battery" message is not displayed. - There is no visual damage to the instrument or test leads. - Test Leads continuity: Using an ohm-meter, check the resistance/continuity of the leads.
  • Page 19 11. Insulation Resistance Testing with 8PK-4103 IN Warning : Insulation test should be conducted on circuits that are de-energized. Ensure circuits are not live before commencing testing. 8PK- 4103 IN Turn instrument "ON" by pressing the "ON" button. The L.C.D. display will advance to the following screen. Select Test 2.5KV, 1KV, or 500V Select insulation test voltage, for example, 500V.
  • Page 20 If the system you are trying to test is not voltage free, the beep will sound. The following warning screen will appear. Remove your leads immediately. LIVE WARNING ... Circuit Live !!! If the system is not live, the test will start and the following screen will appear, indicating the test duration and other factors.
  • Page 21 12. Cleaning & Storage WARNING To avoid electrical shock or damage to the meter, do not get water inside the case. Periodically wipe the case with a damp cloth and detergent. Do not use abrasives or solvents. Distributed by:...
  • Page 22 高壓絕緣測試器 商 品 保 證 書 產 品 型 號 ： 購 買 日 期 ： 年 月 日 保 證 說 明 ： １ 本 卡 若 無 購 買 日 期 及 經 銷 商 認 章 者 ， 不 生 效 力 。 ２...