1. Manuals
  2. Brands
  3. Bodine Manuals
  4. Lighting Equipment
  5. CF94
  6. Installation instructions

Bodine CF94 Installation Instructions

Emergency lighting equipment
Hide thumbs
1
2
3
4

Advertisement

Table of Contents

CF94

Installation Instructions

EMERGENCY LIGHTING EQUIPMENT
! IMPORTANT SAFEGUARDS !
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. To prevent high voltage from being present on red & yellow output leads prior to installation, inverter
connector must be open. Do not join inverter connector until installation is complete and AC power is
supplied to the emergency ballast.
2. This product is for use with one 13 W - 42 W or two 13 W - 39 W (4-pin) compact fluorescent lamps without
integral starters.
3. The emergency ballast must be connected to an unswitched AC power source (120 or 277 VAC, 60 Hz).
4. When installing the emergency ballast, make sure all connections are in accordance with the National
Electrical Code and any local regulations.
5. To reduce the risk of electric shock, disconnect both normal and emergency power supplies and inverter
connector of emergency ballast before servicing.
6. This product is for use with indoor fixtures except air handling heated air outlets, and wet, damp, or
hazardous locations.
7. Do not attempt to service the battery. The emergency ballast uses a sealed, no–maintenance battery.
Contact the manufacturer for information on service.
8. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
9. Do not install near gas or electric heaters.
10. Servicing should be performed by qualified service personnel.
11. Do not use this equipment for other than intended use.
THIS PRODUCT CONTAINS A RECHARGEABLE NICKEL-CADMIUM BATTERY.
236 Mt. Pleasant Rd. • Collierville, TN USA 38017-2752 • Tech Support 888-263-4638 • Fax 901-854-1630 • www.philips.com/bodine
SAVE THESE INSTRUCTIONS
THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.
© Philips Emergency Lighting
A Division of Philips Electronics North America Corporation
WHEN USING ELECTRICAL EQUIPMENT, BASIC
SAFETY PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED, INCLUDING THE FOLLOWING:
Ni - Cd
04/06/11
70094006

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CF94 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Bodine CF94

Summary of Contents for Bodine CF94

  • Page 1: Installation Instructions

    THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY. 04/06/11 © Philips Emergency Lighting A Division of Philips Electronics North America Corporation 236 Mt. Pleasant Rd. • Collierville, TN USA 38017-2752 • Tech Support 888-263-4638 • Fax 901-854-1630 • www.philips.com/bodine 70094006...
  • Page 2 INSTALLATION WARNINGS: 1. TO PREVENT DAMAGE TO THE EMERGENCY BALLAST, JOIN THE BATTERY CONNEC- TOR BEFORE SUPPLYING AC POWER TO THE EMERGENCY BALLAST. 2. TO PREVENT HIGH VOLTAGE FROM BEING PRESENT ON RED & YELLOW OUTPUT LEADS PRIOR TO INSTALLATION, INVERTER CONNECTOR MUST BE OPEN. DO NOT JOIN INVERTER CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED TO THE EMERGENCY BALLAST.
  • Page 3 INSTALLATION STEP #4 WIRING THE EMERGENCY BALLAST > Determine the type of AC ballast installed in the fixture. > Select the appropriate wiring diagram to connect the emergency ballast to the AC ballast and lamp. > See back page for more detailed wiring schematics. The emergency ballast can be used with multi-lamp fixtures.
  • Page 4 EMERGENCY BALLAST AND AC BALLAST MUST BE FED FROM THE SAME BRANCH CIRCUIT TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER BALLASTS. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS. WIRING DIAGRAMS FOR 1-LAMP EMERGENCY OPERATION FIG A ONE (1) LAMP CIRCLINE RAPID START BALLAST FIG B TWO (2) LAMP CIRCLINE RAPID START BALLAST WALL WALL...

Table of Contents