Philips 190P7 Service Manual
Philips 190P7 Service Manual

Philips 190P7 Service Manual

19" lcd color monitor
Hide thumbs Also See for 190P7:
Table of Contents

Advertisement

www.DataSheet.co.kr
19" LCD Color Monitor
Service
Service
Service
Description
Table Of Contents.................................................1
Revision List........................................................2
Important Safety Notice.........................................3
1. Monitor Specifications...................................4
2. LCD Monitor Description..................................5
3. Operation instructions.......................................6
3.1 General Instructions.................................6
3.2 Control buttons..........................................6
3.3 Adjusting the Picture..........................................7
3.4 Connecting to the PC ....................................11
4. Input/Output Specification.................................12
4.1 Input Signal Connector...................................12
4.2 Factory Preset Display Modes.............................13
4.3 Pixel Defect Policy.......................................14
5. Block Diagram...........................................17
5.1 Monitor Exploded View..............................17
5.2 Software Flow Chart..............................18
5.3 Electrical Block Diagram.................................20
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS
AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING

TABLE OF CONTENTS

Page Description
SAFETY NOTICE
ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
6. Schematic Diagram....................................22
6.1 Main Board.................................................22
6.2 Power Board..................................................27
7. PCB Layout.......................................................29
7.1 Main Board.........................................................29
7.2 Power Board.......................................................32
7.3 Key Board.................................................35
7.4 USB Board....................................................35
8. Wiring Diagram................................................ 36
9. Mechanical Instructions.....................................37
10.Trouble shooting........................................48.
11. Repair Flow Chart...........................................50
12. ISP Instructions......................................................55
13. DDC Instructions............................................61
15. Spare Parts List..................................................74
16. General Product Specification............................88
1
190P7
Horizontal Frequency
30- 83KHz
Page
GB 3138 106 10514
Datasheet pdf - http://www.DataSheet4U.net/

Advertisement

Table of Contents
loading

Summary of Contents for Philips 190P7

  • Page 1: Table Of Contents

    19” LCD Color Monitor 190P7 Service Service Service Horizontal Frequency 30- 83KHz TABLE OF CONTENTS Description Page Description Page Table Of Contents........………….1 6. Schematic Diagram…....………..22 Revision List........…………….2 6.1 Main Board…..…..…………………………………22 Important Safety Notice……………......3 6.2 Power Board…….………………….…………………27 1. Monitor Specifications……….....…..4 7.
  • Page 2: Revision List

    19” LCD Color Monitor 190P7 Revision List Version Release Date Revision History May.11, 2006 Initial release, Draft Version Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 3: Important Safety Notice

    NOT EXHAUSTIVE. Philips could not possibly know, evaluate and advise the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, Philips has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by Philips must first satisfy himself thoroughly that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected.
  • Page 4: Monitor Specifications

    19” LCD Color Monitor 190P7 1. Monitor Specifications Screen type Active matrix - TFT LCD Panel Type M190EG01 (AUO) Size 19.0" Pixel pitch 0.294mm(H) x 0.294mm(V) LCD Panel Viewable angle (CR=10) Horizontal 178º, Vertical 178º (type) (AUO) Response time 8 ms (type) TTL level, input impedance 2.2k OHM terminate...
  • Page 5: Lcd Monitor Description

    19” LCD Color Monitor 190P7 2. LCD Monitor Description The LCD MONITOR will contain a main board, PWPC board, keypad board and a USB board which house the flat panel control logic, brightness control logic and DDC. The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips each voltage.
  • Page 6: Operation Instructions

    19” LCD Color Monitor 190P7 3. Operation instructions 3.1 General Instructions Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor. By changing these settings, the picture can be adjusted to your personal preferences.
  • Page 7: Adjusting The Picture

    Rear View 3.3 Adjusting the Picture This is a feather in all Philips LCD monitors. It allows an end user to adjust screen performance of the monitors directly through an on-screen instruction window. The user interface provides user-friendliness and ease-of-use when operating the monitor.
  • Page 8 19” LCD Color Monitor 190P7 The OSD tree Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to work your way around the different adjustments later on.
  • Page 9 19” LCD Color Monitor 190P7 Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 10 19” LCD Color Monitor 190P7 Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 11: Connecting To The Pc

    190P7 3.4 Connecting to the PC 1) Connect the power and DVI cable to the back of the monitor firmly. (Philips has pre-connected DVI-A cable for the first installation.) 2) Connect the cables to the back of your computer by following theses steps: Turn off your computer and unplug its power cable.
  • Page 12: Input/Output Specification

    19” LCD Color Monitor 190P7 4. Input/Output Specification 4.1 Input Signal Connector DVI A/B connectors Description Pin No. Description Pin No. Description Pin No. T.M.D.S Data 2- * Analog R +5V Power T.M.D.S Data 2+ * Analog G GND (return for + 5V and T.M.D.S Data 2 Shield...
  • Page 13: Factory Preset Display Modes

    19” LCD Color Monitor 190P7 4.2 Factory Preset Display Modes Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 14: Pixel Defect Policy

    19” LCD Color Monitor 190P7 4.3 Pixel Defect Policy Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 15 19” LCD Color Monitor 190P7 Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 16 19” LCD Color Monitor 190P7 Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 17: Block Diagram

    19” LCD Color Monitor 190P7 5. Block Diagram 5.1 Monitor Exploded View...
  • Page 18: Software Flow Chart

    19” LCD Color Monitor 190P7 5.2 Software Flow Chart Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 19 19” LCD Color Monitor 190P7 MCU Initializes. 2) Is the EEprom blank? 3) Program the EEprom by default values. 4) Get the PWM value of brightness from EEprom. 5) Is the power key pressed? 6) Clear all global flags.
  • Page 20: Electrical Block Diagram

    19” LCD Color Monitor 190P7 5.3 Electrical Block Diagram 5.3.1 Main Board EEPROM Panel Interface M24C16-WMN6TP (CN501) (U303) NT68563EFG NT68663MEFG Keypad Interface (Include Scalar B, ADC, OSD) (Include MCU, Scalar A) (CN503) (U401) (U301) B-HS B-RX A-HS A-RX B-VS...
  • Page 21 19” LCD Color Monitor 190P7 5.3.2 Inverter/Power Board Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 22: Schematic Diagram

    FB104 C122 0.047uF R122 A_BIN 30 OHM 75  R123 C123 C124   0.047uF D110 D111 D112 R124 BAV99 (NC) BAV99 (NC) BAV99 (NC) A_GNDB 150  Title 190P7 Schematic Size Document Number DVI INPUT A Date: Sunday, January 08, 2006 Sheet...
  • Page 23 FB204 C222 0.047uF R222 B_BIN 30 OHM 75  R223 C223 C224   0.047uF D210 D211 D212 R224 BAV99 (NC) BAV99 (NC) BAV99 (NC) B_GNDB 150  Title 190P7 Schematic Size Document Number DVI INPUT B Date: Sunday, January 08, 2006 Sheet...
  • Page 24 MCU_VDD 470UF/16V FB304 CN301 CN302 1000 OHM MCU_VDD R328 IICSCL   (NC) IICSDA +1.8VCC R329   (NC) CONN (NC) CONN (NC) TO RS232 TO DEBUG Title 190P7 Schematic Size Document Number NT68663 (MCU+SCALER A) Date: Sunday, January 08, 2006 Sheet...
  • Page 25 OSCI 10uF 0.1uF 0.1uF 0.1uF OSCO VSO_B IN_VSO/GPO4 GPO1/ALE HSO_B IN_HSO/GPO5 CSn/REFCKO/GPO6 GPO7/DDC0_SDA AD0/GPO2 GPO8/DDC0_SCL R404 DVDD AD1/GPO3 GPO9/PWM1 10K  R405 BRIGHTNESS 3,5 GPO10/PWM0 100  Title 190P7 Schematic Size Document Number NT68563 (SCALER B) Date: Sunday, January 08, 2006 Sheet...
  • Page 26 100UF/25V +12VCC R526 AUDIO_STANDBY   (NC) +3.3VCC C522 0.001uF (NC) +12VCC C526 C528 0.1uF 0.1uF CONN (NC) CONN Title CONNECTOR FOR USB HUB & 190P7 Schematic AUDIO BD 2.0 mm Size Document Number CONNECTOR Date: Sunday, January 08, 2006 Sheet...
  • Page 27: Power Board

    19” LCD Color Monitor 190P7 6.2 Power Board 715G1813-1 L902 S901 R931 C8B-R6H spotgap_NC 2R2_1206 R900 C931 R932 680K C900 0.001uF/250V 2R2_1206 3.3nF/500V T901 R901 VAR901 C908 L901 680K +12VCC CN901 0.47uF/275V varistor_NC AC SOCKET R904 R905 C920 D931 BD901 1.5M/R1206...
  • Page 28 19” LCD Color Monitor 190P7 PT801 C802 CN831 5pF/3KV R834 CONN +12V   6.2M 1/2W_NC C803 C801 5pF/3KV R835 10pF/6KV R831 C820 C821 R822 R823 1K  10K_1% 470uF/25V R824 C838 24:24:2400 7.5K_1%_NC C811 1000pF R836 10K_1% D833 D831 R804 BAV70/SOT23B BAV99  ...
  • Page 29: Pcb Layout

    19” LCD Color Monitor 190P7 7. PCB Layout 7.1 Main Board 715G1791-1 Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 30 19” LCD Color Monitor 190P7 Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 31 19” LCD Color Monitor 190P7 Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 32: Power Board

    19” LCD Color Monitor 190P7 7.2 Power Board 715G1813-1 Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 33 19” LCD Color Monitor 190P7 Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 34 19” LCD Color Monitor 190P7 Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 35: Key Board

    19” LCD Color Monitor 190P7 7.3 Key Board 715G1805-1 7.4 USB Board 715G1794-1 Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 36: Wiring Diagram

    19” LCD Color Monitor 190P7 8. Wiring Diagram Panel CN851 CN853 CN951 Power Board CN501 CN502 CN901 Main Board CN831 CN503 CN833 CN505 CN201 CN101 AC-IN 1654 1651 1652 CN001 Key Board 1601 USB Board Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 37: Mechanical Instructions

    19” LCD Color Monitor 190P7 9. Mechanical Instructions Steps of dismantling base stand from base column Step 1: Place the monitor face down on a smooth surface as Fig 1. Be careful to avoid scratch and injury during the uninstallation.
  • Page 38 19” LCD Color Monitor 190P7 Step 3: Firmly insert the base removal tool into four-pronged clicks as Fig 3. Fig3 Step 4: Pull out the foot from base as Fig 4 Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 39 19” LCD Color Monitor 190P7 Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 40 19” LCD Color Monitor 190P7 Steps of assembling and disassembling side cover 1. Press down the rim of side cover and hold as Fig 1. (Press direction is toward panel surface side.) Fig1 2. Pull out the side cover horizontally as Fig 2.
  • Page 41 19” LCD Color Monitor 190P7 3. Tongues and grooves position on side cover and back cover as Fig 3. Assembling the side cover: 1. Have 6 tongues on side cover aligned with back cover’s 6 grooves then push side cover horizontally into back cover.
  • Page 42 19” LCD Color Monitor 190P7 1. Back View as Fig.1 Fig.1 2. Remove base stand as Fig.2. Remove the four screws to remove the base stand as Fig.2 Fig.2 Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 43 19” LCD Color Monitor 190P7 3. Disassembling the side covers as Fig.3. Fig.3 Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 44 19” LCD Color Monitor 190P7 4. Remove rear cover as Fig.4. Remove the four screws to remove the rear cover as Fig.4 Fig.4 5. Remove the shield as Fig.5 Remove the nine screws as Fig.5 to remove the shield.
  • Page 45 19” LCD Color Monitor 190P7 6. Remove the main board, the power board and the USB board as Fig.6 Remove the eleven screws as Fig.6 to remove the main board, the power board and the USB board. Fig.6 7. Remove the front panel as Fig.7.
  • Page 46 19” LCD Color Monitor 190P7 8. Remove the main frame as Fig.8 Remove the four screws as Fig.8 to remove the main frame. Fig.8 Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 47 19” LCD Color Monitor 190P7 Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 48: Trouble Shooting

    19” LCD Color Monitor 190P7 10. Trouble Shooting This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative. Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 49 19” LCD Color Monitor 190P7 Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 50: Repair Flow Chart

    19” LCD Color Monitor 190P7 11. Repair Flow Chart (1). No Power No power Press power key and look if the picture is normal Please reinsert and make sure the AC of 100-240 is normal Reinsert or check the power section Measure U502 Pin2=3.3V,...
  • Page 51 19” LCD Color Monitor 190P7 (2). No Picture No picture Measure U502 PIN2=3.3V, U501 PIN2=1.8V? Replace U501, U502 X301 oscillate waveforms are normal Replace X301 Check if the sync signal from computer is output and video cable is connected normally...
  • Page 52 19” LCD Color Monitor 190P7 (3). White screen White screen Measure Q502 base X301 oscillate is high level? waveform is normal Replace X301 Check Q502, Q501 is broken Check reset circuit of or CN406 solder? U401 is normal Check Correspondent component.
  • Page 53 19” LCD Color Monitor 190P7 9.2.2 Power/Inverter Board No power Adapter Board Check CN951 pin 6/7 = 12V? Check AC line volt 100-240V Check AC input Check the voltage of C907 (+) Check bridge rectified circuit and F901 circuit...
  • Page 54 19” LCD Color Monitor 190P7 Inverter board No power Check C811 (+) =12V Check adapter section Check ON/OFF signal Check Interface section or main board Check U811 pin 2=12V? Check Q801 Check U811 Pin1/pin15 have the output of sawtooth wave at short time...
  • Page 55: Isp Instructions

    19” LCD Color Monitor 190P7 12. ISP Instruction (1). Install the program software a. First decompressing files , as follow: Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 56 19” LCD Color Monitor 190P7 b. Double – click , start to install as follows: Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 57 19” LCD Color Monitor 190P7 c. There will be a shortcut key appears on the desktop. Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 58 19” LCD Color Monitor 190P7 (2). Connect the ISP board as follow: Connect to the Philips 190P by a VGA to DVI-A Connect to commutator as the PC LPT below fig ,running the program as follows: a. Double-click Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 59 19” LCD Color Monitor 190P7 b. Click icon, search the program” PHILIPS_190P7_NT68663_128K_LG19_EU_V1.00.hex”, and click open: c. After click “OPEN”, there would be a dialog box, select Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 60 19” LCD Color Monitor 190P7 c. Click icon, the writer is in processing… d. Until appears the follow Fig, writer completed. Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 61: Ddc Instructions

    19” LCD Color Monitor 190P7 13. DDC Instruction (1). Install software You must install the at the first. The processing as follows: Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 62 19” LCD Color Monitor 190P7 Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 63 Note: After installation, you must restart the PC to take the setup to effect. (2). Connect the DDC board as follow: Connect to the Philips 190P by Connect to the PC LPT a VGA to DVI-A commutator as below fig 12V Input Note: The 2 DVI-I ports should be respectively program.
  • Page 64 19” LCD Color Monitor 190P7 A. Program digital and analog EDID data ,appear as follow Fig: a. Double-click b. Key in ”1” as follow Figs: Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 65 19” LCD Color Monitor 190P7 c. Press Enter key, then appears the following Fig: d. Key in the Serial Number printed on the barcode label, then click “OK” 14 codes, for example. Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 66 19” LCD Color Monitor 190P7 e. When digital EDID program completed, appears the following Fig: f. When ANALOG EDID program completed, appears the following Fig: Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 67 19” LCD Color Monitor 190P7 B. Read digital and analog EDID data. a. Key in ”2” as follow Figs: Press Enter key, then appears the following Fig: Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 68 19” LCD Color Monitor 190P7 Press Enter key to read analog as follow: Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 69 19” LCD Color Monitor 190P7 128 bytes EDID Data (Hex): x0 x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC xD xE xF 00 FF FF FF FF FF FF 00 41 0C 41 08 01 00 00 00...
  • Page 70 1280x1024 @ 60Hz. <-x-Detailed Timing Descriptions-x-> <---Detailed Timing Descriptions---> Detailed Timing: FF (Monitor SN) ' AU 000001' Detailed Timing: FC (Monitor Name) 'Philips 190P' Detailed Timing: FD (Monitor limits) Min. V. rate: 56Hz Max. V. rate: 76Hz Min. H. rate: 30KHz Max.
  • Page 71 19” LCD Color Monitor 190P7 128 bytes EDID Data (Hex): x0 x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC xD xE xF 00 FF FF FF FF FF FF 00 41 0C 41 08 01 00 00 00...
  • Page 72 1280x1024 @ 60Hz. <-x-Detailed Timing Descriptions-x-> <---Detailed Timing Descriptions---> Detailed Timing: FF (Monitor SN) ' AU 000001' Detailed Timing: FC (Monitor Name) 'Philips 190P' Detailed Timing: FD (Monitor limits) Min. V. rate: 56Hz Max. V. rate: 76Hz Min. H. rate: 30KHz Max.
  • Page 73: White Balance, Luminance Adjustment

    10s), release, press the menu again will activate the factory mode, the factory OSD will be at the left top of the screen. Move the cursor to select the Hyson 190P7***********, press OK button to enter into the sub-menu; Move the cursor again to select ” Cool/warm “.
  • Page 74: Spare Parts List

    USB986A1P USB BOARD ASS'Y 9965 000 37770 Panel Part No for TPV Description Philips 12NC 750GLU90G0111M PANEL LCD 19" EG01 V0 PHILIPS AU 9965 000 37757 Accessory and Mechanical Part No for TPV Description Philips 12NC 089G179E30C902 FFC CABLE P-TWO...
  • Page 75 19” LCD Color Monitor 190P7 Main Board Location Part No. for TPV Description Philips 12NC 105   10UF M 50V C316 067G3051007C 9965 000 37771 105   10UF M 50V C507 067G3051007C 9965 000 37771 105   220UF M 25V...
  • Page 76 19” LCD Color Monitor 190P7 R514 061L0603102 CHIPR 1K OHM -5% 1/16W 9965 000 35970 R518 061L0603102 CHIPR 1K OHM -5% 1/16W 9965 000 35970 R210 061L0603102 CHIPR 1K OHM -5% 1/16W 9965 000 35970 R209 061L0603102 CHIPR 1K OHM -5% 1/16W...
  • Page 77 19” LCD Color Monitor 190P7 R119 061L0603222 CHIPR 2.2K OHM -5% 1/16W 9965 000 35977 R120 061L0603222 CHIPR 2.2K OHM -5% 1/16W 9965 000 35977 R219 061L0603222 CHIPR 2.2K OHM -5% 1/16W 9965 000 35977 R220 061L0603222 CHIPR 2.2K OHM -5% 1/16W...
  • Page 78 19” LCD Color Monitor 190P7 C530 065G060310231 CHIP 1000PF 50V NPO 9965 000 36917 C520 065G060310231 CHIP 1000PF 50V NPO 9965 000 36917 C519 065G060310231 CHIP 1000PF 50V NPO 9965 000 36917 C502 065G060310412 CER2 0603 X7R 16V 100N PM10 R...
  • Page 79 19” LCD Color Monitor 190P7 C403 065G060310412 CER2 0603 X7R 16V 100N PM10 R 9965 000 36918 C322 065G060310412 CER2 0603 X7R 16V 100N PM10 R 9965 000 36918 C318 065G060310412 CER2 0603 X7R 16V 100N PM10 R 9965 000 36918...
  • Page 80 . D a t a S h e e t . c o . k r 19” LCD Color Monitor 190P7 D101 093G6442P DIO SW BAV70 SOT23 9965 000 13591 D201 093G6442P DIO SW BAV70 SOT23 9965 000 13591...
  • Page 81 19” LCD Color Monitor 190P7 Power Board Location Part No. for TPV Description Philips 12NC IC902 056G1393A PC123Y22FZOF 9965 000 36055 NR901 061G5810T 8 OHM 4A NTCR BY THINKING 9965 000 36938 R905 061G152M10464 100KOHM 5% 2W 9965 000 36939...
  • Page 82 19” LCD Color Monitor 190P7 Q801 057G7592 RK7002 9965 000 36033 Q871 057G7592 RK7002 9965 000 36033 Q873 057G7604B PDTA144WK SOT346 9965 000 36962 Q821 057G76314 AM9945N 9965 000 36100 Q841 057G76314 AM9945N 9965 000 36100 RJ827 061L0805000 CHIPR 0OHM -5% 1/10W...
  • Page 83 19” LCD Color Monitor 190P7 R873 061L0805202 CHIP 2KOHM 1/8W 9965 000 36971 R816 061L0805203 CHIPR 20KOHM -5% 1/8W 9965 000 36972 R865 061L08052490F RST CHIPR 249 OHM -1% 1/8W 9965 000 37494 R815 061L0805303 CHIP 30K OHM 1/8W...
  • Page 84 19” LCD Color Monitor 190P7 C841 065G080510522 CHIP 1UF 25V X7R 0805 9965 000 36073 C821 065G080510522 CHIP 1UF 25V X7R 0805 9965 000 36073 C811 065G080510522 CHIP 1UF 25V X7R 0805 9965 000 36073 C915 065G080512322 CHIP 12NF 25V X7R 0805...
  • Page 85 19” LCD Color Monitor 190P7 FB901 071G5529 FERRITE BEAD 9965 000 36053 F902 084G554 FOSE 382-5A 250V SICKMANN 9965 000 37005 F901 084G557GP FUSE 3.15A 250V 9965 000 37006 ZD951 093G39A3552T ZENER DIODE P6KE8.2A ZOWIE 9965 000 37007 D926...
  • Page 86 19” LCD Color Monitor 190P7 USB Board Location Part No. for TPV Description Philips 12NC 5634 073G253518LS COI CHOKE 35UH 82M OHM DR10X8 9965 000 37800 1652 088G3514TN USB CONN 9965 000 37338 1651 088G352900TN USB CONN 5401-342-101-92 9965 000 37801...
  • Page 87 19” LCD Color Monitor 190P7 2671 065G060310432 CHIP 0.1UF 50V X7R 9965 000 37393 2680 065G060310432 CHIP 0.1UF 50V X7R 9965 000 37393 2681 065G060310432 CHIP 0.1UF 50V X7R 9965 000 37393 2684 065G060310432 CHIP 0.1UF 50V X7R 9965 000 37393...
  • Page 88: General Product Specification

    19” LCD Color Monitor 190P7 16. General Product Specification . ANALOG AND DIGITAL DUAL INPUT . AUTO PICTURE ADJUSTMENT . 17 FACTORY PRESET MODES AND 33 PRESET MODES WHICH CAN BE RECOVERED TO PRESET MODES, 24 USER MODES . USER FRIENDLY OSD DISPLAY FOR MODE IDENTIFICATION/ADJUSTMENT .
  • Page 89 SUSCEPTIBILITY OF DISPLAY TO EXTERNAL ENVIRONMENT TRANSPORTATION TESTS DISPLAY DISTURBANCES FROM EXTERNAL ENVIRONMENT DISPLAY DISTURBANCES TO EXTERNAL ENVIRONMENT RELIABILITY MEAN TIME BETWEEN FAILURES QUALITY ASSURANCE REQUIREMENTS ACCEPTANCE TEST PHILIPS’ FLAT PANEL MONITORS PIXEL DEFECT POLICY ARTWORKS Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 90: Foreword

    30 minutes that brightness stability is optimal, and follow strictly after panel specification. 2. PRODUCT PROFILE This display monitor unit is a color display monitor enclosed in PHILIPS global styling cabinet which has an integrated tilt and swivel base. 2.1 LCD 2.1.1 Type NR.
  • Page 91: Electrical Characteristics

    19” LCD Color Monitor 190P7 3. Electrical characteristics 3.1 Interface signals 1). DVI-I Analog Input signal : Video, Hsync., Vsync Video : 0.7 Vp-p, input impedance, 75 ohm @DC Sync. : Separate sync TTL level , input impedance 2.2k ohm terminate...
  • Page 92 . D a t a S h e e t . c o . k r 19” LCD Color Monitor 190P7 3.2.3 Audio Cable Length. : 1.8 M +/- 50 mm Connector type. : 3.5-mini jack with lime color on the both end.
  • Page 93 19” LCD Color Monitor 190P7 Adjustable functions: LEVEL LEVEL 3rd LEVEL MONITOR SETUP Exit Brightness Brightness & Contrast Contrast Original Color, 9300K,6500K, Color sRGB, User Define Horizontal Position Vertical Input Selection Analog, Digital /00,/05 English, Spanish, French, German, Italian and...
  • Page 94: Timing Requirement

    19” LCD Color Monitor 190P7 3.3Timing requirement 3.3.1 Mode storing capacity Factory preset modes: 15 Preset modes : 24 User define modes Note: Screen displays perfect picture at 15 factory-preset modes. 2. Screen displays visible picture with OSD warning when input modes are the 34 preset modes 3.3.2 Factory preset modes (15 modes)
  • Page 95 19” LCD Color Monitor 190P7 MODE NO. RESOLUTION 640 x 480 640 x 480 640x480 800 x 600 Dot clock(MHz) 31.500 31.501 37.861kHz 37.5kHz 36kHz 35.2kHz A ( us ) 26.413(832 dots) 26.667 (840 dots) 23.111 (832 dots) 28.444(1024 dots) B ( us ) 1.270(40 dots)
  • Page 96 19” LCD Color Monitor 190P7 MODE NO. RESOLUTION 1024 x 768 1024 x 768 1152 x 864 1152 x 864 Dot clock(MHz) 83.096 94.5 79.9 94.5 61.1kHz 68.7kHz 54.0kHz 63.9kHz A ( us ) 16.367 (1360dots) 14.561(1376 dots) 18.523(1480 dots) 15.661(1480 dots)
  • Page 97 19” LCD Color Monitor 190P7 MODE NO. RESOLUTION 1280 x 1024 1280 x 1024 1280 x 1024 688 x 556 Dot clock(MHz) 130.223 138.008 76kHz 80kHz 81.1kHz 31.25kHz A ( us ) 13.158(1712 dots) 12.504(1688 dots) 12.326(1664 dots) 32 (864 dots) B ( us ) 1.024 (133 dots)
  • Page 98: Horizontal Scanning

    19” LCD Color Monitor 190P7 3.4 Horizontal scanning Sync polarity : Positive or Negative Scanning frequency : 30 – 83 K Hz 3.5 Vertical scanning Sync polarity : Positive or Negative Scanning frequency : 56 - 76 Hz 3.6 Power input connection...
  • Page 99: Brightness Uniformity

    5.1 Cosmetic - Philips ID 5.2 Mechanical data files - ProE files required 5.3 Location of Philips logo - Per Philips make-up sheet 5.4 Gap between Panel and front bezel < 0.8 mm 5.5 Location of Control icons - Per Philips make-up sheet...
  • Page 100: Tilt And Swivel Base

    All major plastic parts (bezel, back cover, base) need to be molded from same resin. 5.11 Texture/Glossing of housing • The texture area and texture no should follow Philips make-up sheet. • The exterior surfaces shall have a uniform texture.
  • Page 101: Environmental Characteristics

    19” LCD Color Monitor 190P7 B. Transportation test specification for China/India • Package test 1. Random Vibration test 2. Drop test 3. Cold Drop test (for design reference) • Un-package test 1. Sine vibration (operating) 2. Half sine shock test (non operation) 5.16 Pallet / Container loading...
  • Page 102: Philips' Flat Panel Monitors Pixel Defect Policy

    19” LCD Color Monitor 190P7 9. Philips’ Flat Panel Monitors Pixel Defect Policy Philips’ Flat Panel Monitors Pixel Defect Policy, 190P7 is PP panel product. BRIGHT DOT DEFECTS ACCEPTABLE LEVEL MODEL 190P7 1 lit sub-pixel 2 adjacent lit sub-pixels...
  • Page 103 19” LCD Color Monitor 190P7 Fig 2: Cross talk pattern Gray level 46 (64 Gray level) Fig 3: Cross talk Pattern Center at Gray level 0 (Black) Datasheet pdf - http://www.DataSheet4U.net/...
  • Page 104 19” LCD Color Monitor 190P7 SEPARATE SYNC. VIDEO HORIZONTAL VIDEO VERTICAL COMPOSITE SYNC. VIDEO HORIZONTAL FIG-4 TIMING CHART -1 Datasheet pdf - http://www.DataSheet4U.net/...

Table of Contents