Advertisement
Dear Customer:
Designed specifically for rip-cutting narrow strips
from sheet stock and for cross-cutting to close
tolerances, the MicroLux
®
even cut plastic, thin non-ferrous metals and
printed circuit board with our optional fine-tooth
blades.
State-of-the-Art production and testing procedures
ensure he maximum reliability from your power
tool.
This manual includes:
• Safety instructions
• Installation and operating instructions
• Spare parts list
• Warranty information
Reading this manual will:
• Help you understand the machine's
operation.
• Avoid malfunctions due to improper
operation.
• Increase the life of the machine.
Always keep this manual close at hand.
Do not operate the machine unless you are
fully familiar with it. Please observe the safety
instructions.
Use only original MicroLux spare parts.
MM032218
Mini Table Saw will
Operating Instructions for
#87775 MicroLux
Please read the following safety instructions thoroughly and follow them
Safety Instructions
before starting to work with the machine:
• Always wear safety glasses when operating power tools.
• Keep the work area clean and tidy.
• Do not use electric tools in rain, under wet conditions, near flammable
liquids or gasses.
• Avoid contact with grounded parts, such as pipes, radiators, cookers or
refrigerators.
• Store tools out of the reach of children.
• Do not overload the machine.
• Do not wear loose clothes or jewelry.
• Do not carry the machine by the electric cable.
• Keep the electrical cable away from heat, oil and sharp edges.
If necessary have it replaced by a professional.
• Fasten the machine securely to a work table.
• Replace dull saw blades.
• Clean the machine thoroughly after completing your work.
• Pull out the electric plug before maintaining the machine, before changing
the saw blade or the toothed belt, or when not using the machine.
• Make sure that the machine is switched off before connecting it to the wall
outlet.
• Check the machine for obvious damage before use. Replace defective
parts.
• Repairs in the electrical system should be carried out by a specialist.
• Use only accessories and spare parts which are recommended.
• Use a push stick when working near the saw blade.
Miniature Table Saw
®
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for MICRO-MARK MicroLux 87775
Summary of Contents for MICRO-MARK MicroLux 87775
- Page 1 Operating Instructions for #87775 MicroLux Miniature Table Saw ® Dear Customer: Designed specifically for rip-cutting narrow strips Please read the following safety instructions thoroughly and follow them Safety Instructions from sheet stock and for cross-cutting to close before starting to work with the machine: tolerances, the MicroLux Mini Table Saw will •...
-
Page 2: Installing And Removing Blades
Parts bags contain the following items: 1 Miter Gauge 1 Rip Fence 3 Wood Screws 1 Machine Screw 1 Vacuum Adapter 2 Hex Key Wrenches 2 C-Clamps Understanding Your New Saw Your saw is designed to run on standa rd household current (110V 60Hz). This saw will cut softwoods, hardwoods, plywood, plastics and thin non-ferrous metals quickly and cleanly with the appropriate blades installed. -
Page 3: Mounting The Saw
A Note about Saw Blades When installing a new saw blade, it is crucial to identify the proper orientation of the blade. While some blades are marked with a directional arrow, others are not. To avoid any confusion, the best way to identify the proper direction of blade rotation is to look at the blade’s teeth. -
Page 4: Rip Fence
Rip Fence The rip fence may be mounted from the right or left side of the table. To mount the fence from the right side, slide the right side door out a bit to access the slot on the underside of table; this slot accommodates the corresponding hook-shaped tab on the fence. -
Page 5: Miter Gauge
Miter Gauge The included miter gauge is not only useful for making 90° cross cuts and angled cuts, you may also use it as a push stick / sliding fence. Always set the miter gauge to the desired angle and firmly lock it into position prior to powering up the saw. Once the angle is set, place stock to be cut on the saw table and hold it firmly against the miter gauge. -
Page 6: Limited Warranty
Micro-Mark makes no other warranty of any kind whatever, expressed or implied, and all implied warranties of merchantability and fitness for a particular purpose which exceed the above mentioned obligation are hereby disclaimed by Micro-Mark and excluded from this warranty.
Need help?
Do you have a question about the MicroLux 87775 and is the answer not in the manual?
Questions and answers