Related Manuals for HELVAR mDim series
Summary of Contents for HELVAR mDim series
- Page 1 µDim Microwave Sensors User Manual P e o p l e | I n n o v a t i o n s | S o l u t i o n s...
-
Page 2: Table Of Contents
SL-MW-SW SL-MW-AN SL-MW-DA Up to 8m microwave sensing Lux sensor Presence detection Infrared remote setting Relay output 1-10 V Dimming output DALI Dimming output Doc No: T13 144 1C Data is subject to change without notice. More information at: www.helvar.com... -
Page 3: Technical Data
1) No presence detected, daylight, lights OFF 2) Presence detected,sufficient daylight, lights OFF 3) Presence detected, insufficient daylight, lights ON 4) No presence detected, night time, lights OFF Data is subject to change without notice. More information at: www.helvar.com Doc No: T13 144 1C... - Page 4 If this causes a problem, reduce its sensitivity using the SA-IR-PROG 2.8m Programmer. Data is subject to change without notice. More information at: www.helvar.com Doc No: T13 144 1C...
- Page 5 4) Presence detected, insufficient daylight. Detector measures and implements maintained illumininance 2) Presence detected,sufficient daylight, lights OFF 5) No presence detected, night time, lights OFF Data is subject to change without notice. More information at: www.helvar.com Doc No: T13 144 1C...
- Page 6 If this causes a problem, reduce its sensitivity using the SA-IR-PROG 2.8m Programmer. • Doc No: T13 144 1C Data is subject to change without notice. More information at: www.helvar.com...
- Page 7 4) Presence detected, insufficient daylight. Detector measures and implements maintained illumininance 2) Presence detected,sufficient daylight, lights OFF 5) No presence detected, night time, lights OFF Data is subject to change without notice. More information at: www.helvar.com Doc No: T13 144 1C...
- Page 8 If this causes a problem, reduce its sensitivity using the SA-IR-PROG 2.8m Programmer. Doc No: T13 144 1C Data is subject to change without notice. More information at: www.helvar.com...
-
Page 9: Dimensions And Mounting Options
6mm thick, remove bottom of retention arms with side cutters. A 44mm diameter hole will be required in the panel to mount the flush mount bracket. 44 mm 6 mm Data is subject to change without notice. More information at: www.helvar.com Doc No: T13 144 1C... -
Page 10: Connections
SL-MW-AN Sensor head Power supply unit LOAD max 2A C0(-) C1(+) 1-10V Ballast SL-MW-DA Sensor head Power supply unit LOAD max 2A DALI Ballast Data is subject to change without notice. More information at: www.helvar.com Doc No: T13 144 1C... -
Page 11: Setup
• When adjusting, allow the output level to settle by changing very gradually. • To disable the constant light function completely, set the level to maximum. Data is subject to change without notice. More information at: www.helvar.com Doc No: T13 144 1C... -
Page 12: Programmming
Shift Use this button to select the settings in red and blue signif ied by the ‘Shif t 1’ and ‘Shift 2’ LEDs Data is subject to change without notice. More information at: www.helvar.com Doc No: T13 144 1C... - Page 13 µDim Data is subject to change without notice. More information at: www.helvar.com Doc No: T13 144 1C...
-
Page 14: Fault Finding
Doc No. T13 144 1C electrician in accordance with the latest Issue 2 edition of the IEE wiring regulations. Product not to be used in the U.S.A. Data is subject to change without notice. More information at: www.helvar.com Doc No: T13 144 1C...
Need help?
Do you have a question about the mDim series and is the answer not in the manual?
Questions and answers