Honeywell 5834-4EN Installation Instructions page 2

REPLACING THE BATTERY
The LED will not flash during transmission if the battery is low. Replace the battery as
follows.
1. Remove the screw from the case back, then remove the case back.
2. Insert the blade of a small screwdriver under the battery as shown.
3. Twist the screwdriver to release the battery.
IMPORTANT: After removing the old battery, wait 1 minute before installing a new battery.
4. With the Positive (+) end of a new battery facing UP, insert the battery as shown, sliding it
under the gold tab, then pressing down to snap into place.
IMPORTANT: Positive (+) end must face up.
Use Panasonic CR2032, Duracell DL2032, or SENER CR2032 lithium battery only.
5. Replace the case back and replace the screw to secure the case.
• Improper installation will result in damage to the battery.

• Do not remove the printed circuit board.
Failure of Replaceable Batteries
This wireless key has been designed to provide several years of battery life under normal
conditions. The expected battery life is a function of the device environment, usage and type.
Ambient conditions such as high humidity, high or low temperatures, or large temperature
fluctuations may reduce the expected battery life.
If the batteries need to be replaced, this device reports a low battery condition to the control
panel as a trouble condition when a button is pressed. In addition the LED will not flash when
a button is pressed. However, if the device is unused for a long period of time, it may fail to
operate as expected. Regular testing and maintenance will keep the system in good
operating condition for the lifetime of the product.
IMPORTANT! This wireless key is intended as a convenience to the user and should not
be considered as a life safety device. If life safety is important, please select a supervised
wireless key (e.g. type 5802MN).
SPECIFICATIONS
Unit Dimensions: 2.25" x 1.25" x 0.5"
(57mm x 31.75mm x 12.7mm)
Battery: 3V, 210mAh, Panasonic CR2032, Duracell DL2032, or SENER CR2032
WARRANTY INFORMATION
For the latest warranty information, please go to:
http://www.security.honeywell.com/hsc/resources/wa
DOCUMENTATION AND ONLINE SUPPORT
For the latest documentation and online support information, please go to:
https://mywebtech.honeywell.com/
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL
WITH WHICH THIS DEVICE IS USED FOR LIMITATIONS OF THE ENTIRE
ALARM SYSTEM.
IMPORTANT SECURITY NOTICE
Please inform the User about the security importance of their key fob, and what
to do if it is lost.
Explain that the key fob is similar to their keys or access card. If lost or stolen,
another person can compromise their security system. They should immediately
notify the Dealer/Installer of a lost or stolen key fob. The Dealer/Installer will then
remove the key fob programming from the security system.
Ê800-05637V4{Š
800-05637V4 3/15 Rev. B
Removing the Battery
TO REMOVE BATTERY,
GENTLY SLIDE SCREWDRIVER
BLADE UNDER BATTERY HERE
Installing the Battery
INSTALL WITH POSITIVE (+)
SIDE UP. SLIP BATTERY
UNDER GOLD TAB THEN
PRESS DOWN
IC: #
FCC ID: #
The IC Model # can be found on the inside cover of the battery
compartment.
FEDERAL COMMUNICATIONS COMMISSION
STATEMENTS:
The user shall not make any changes or modifications to the
equipment unless authorized by the installation Instructions or
User's Manual. Unauthorized changes or modifications could void
the user's authority to operate the equipment.
FCC/IC STATEMENT
This device complies with Part 15 of FCC Rules, and RSS-210 of
IC. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) This device
must accept any interference received, including interference that
may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de
RSS-210 des industries Canada. Son fonctionnement est soumis
aux conditions suivantes: (1) Cet appareil ne doit pas causer
d'interférences nuisibles. (2) Cet appareil doit accepter toute
interférence reçue y compris les interférences causant une
réception indésirable.
See above for location of FCC ID and IC Certification Number.
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2010 Honeywell International Inc.
www.honeywell.com/security
GOLD
TAB
REMOVE
SCREW
TO OPEN
CASE
BATTERY
5834-004-V0
INSTALL UNDER
GOLD TAB
THEN PRESS
DOWN
IMPORTANT
POSITIVE (+)
SIDE MUST
FACE UP
5834-4-002-V0