Download Print this page

Pronteau PROBOIL.2 Replacement Manual

Filter replacement guide
Hide thumbs Also See for PROBOIL.2:

Advertisement

Quick Links

The filter system provided with PROBOIL will help to prevent the calcification (scaling) of the
boiler and improve the taste of the water. Each installation has a different number of people
using it, a different usage pattern and an individual water hardness "GB Clark rating". Because
of this you must judge for yourself if the filter needs changing or not, as no two installations are
the same. We recommend replacing the filter at 6 months and a maximum life of 1 year,
depending on usage.
Installation preparation
Installation preparation
Installation preparation
Installation preparation
Before installing your new filter it is essential
Before installing your new filter it is essential
Before installing your new filter it is essential
Before installing your new filter it is essential
that you switch off the mains power to the boiler
that you switch off the mains power to the boiler
that you switch off the mains power to the boiler
that you switch off the mains power to the boiler
and wait 10 minutes for it to cool before continuing.
and wait 10 minutes for it to cool before continuing.
and wait 10 minutes for it to cool before continuing.
and wait 10 minutes for it to cool before continuing.
Using any filter type not developed and
Using any filter type not developed and
Using any filter type not developed and
Using any filter type not developed and
approved for use with this tap and boiler will
approved for use with this tap and boiler will
approved for use with this tap and boiler will
approved for use with this tap and boiler will
invalidate your warranty.
invalidate your warranty.
invalidate your warranty.
invalidate your warranty.
When adding or changing the filter a small
When adding or changing the filter a small
When adding or changing the filter a small
When adding or changing the filter a small
amount of residual water will remain in the system,
amount of residual water will remain in the system,
amount of residual water will remain in the system,
amount of residual water will remain in the system,
so have a small bowl and dry clot
so have a small bowl and dry clot
so have a small bowl and dry clot
so have a small bowl and dry cloth to hand.
Filter installation
Filter installation
Filter installation
Filter installation
1. Ensure the boiler is powered off and the left hand (hot water) lever is fully off and that no water is
passing through and out of the tap spout end before commencing.
2. Unclip the filter cartridge (C7) from the bracket (C6). Remove the pipes (C4) from both ends of filter (C7).
To remove the pipes (C4) from the filter (C7) you must firmly push the small white ring on the very end of
the filter (C7) towards the middle of the filter whilst simultaneously pulling the pipe (C4) away from the
filter body (C7). It is normal for some water to be released when the pipes are removed.
3. Firmly push connect the ¼" pipe (C4) between pushfit (C3) and new filter cartridge inlet (C7), repeat this
from the filter cartridge outlet (C7) to the boiler inlet (E1). You must respect the direction of flow as
indicated on the label, visually check the ends of pipe (C4) are not worn before reconnecting.
4. Clip the filter cartridge (C7) into the bracket (C6) as shown.
After installation of the filter is complete
After installation of the filter is complete
After installation of the filter is complete
After installation of the filter is complete
1. Turn on the hot water handle fully, keep the lever open until all trapped air is expelled and cold
(unboiled) water exits the centre channel of the tap spout, then flush a further 10 litres of cold (unboiled)
water through the filter, boiler and tap. You may notice discolouration to the water at first. This is loose
carbon fines from the filter, it is normal, harmless and will pass with flushing.
2. Whilst flushing as the system starts to refill, check carefully all new water connections for leaks. Once
complete, turn off the left hand hot water handle.
3. This filter works best at an approximate flow rate of 2 litres per minute (with the left hand hot water
handle fully turned on). This flow rate is determined by the specific incoming cold water pressure to your
tap. The filter performance characteristics will be affected if the flow rate is not approximately 2 litres per
minute.
h to hand.
h to hand.
h to hand.
Filter Replacement Guide
Filters must be replaced at the recommended
Filters must
be replaced at the recommended
Filters must
Filters must
be replaced at the recommended
be replaced at the recommended
schedule noted on the filter label. Ensure you write the
schedule noted on the filter label. Ensure you write the
schedule noted on the filter label. Ensure you write the
schedule noted on the filter label. Ensure you write the
installation date on the label.
installation date on the label.
installation date on the label.
installation date on the label.
All parts should be removed from their packaging
All parts should b
e removed from their packaging
All parts should b
All parts should b
e removed from their packaging
e removed from their packaging
and inspected for any transport damage and that all parts
and inspected for any transport damage and that all parts
and inspected for any transport damage and that all parts
and inspected for any transport damage and that all parts
are present prior to installation.
are present prior to installation.
are present prior to installation.
are present prior to installation.
Ensure the left hand (hot water) lever is fully off and
Ensure the left hand (hot water) lever is fully off and
Ensure the left hand (hot water) lever is fully off and
Ensure the left hand (hot water) lever is fully off and
that no water is passing through and out of the tap spout
that no water is passing through and out of the tap spout
that no water is passing through and out of the tap spout
that no water is passing through and out of the tap spout
end before commencing.
end before commencing.
end before commencing.
end before commencing.
PROBOIL.2
Scan here to
Scan here to
Scan here to
Scan here to
link to a video
link to a video
link to a video
link to a video
demo
demo
demo
demo

Advertisement

loading

Summary of Contents for Pronteau PROBOIL.2

  • Page 1 PROBOIL.2 Filter Replacement Guide The filter system provided with PROBOIL will help to prevent the calcification (scaling) of the boiler and improve the taste of the water. Each installation has a different number of people using it, a different usage pattern and an individual water hardness “GB Clark rating”. Because...
  • Page 2 4. To change the flow rate through the filter and boiler adjust the cold water isolation valve (B5 not shown, see tap installation instructions) using a slotted screwdriver, kitchen measuring jug and a watch whilst the left hand hot water handle is fully turned on. 5.