Alarmtech PSV 2465-40 Instruction Manual

Instruction manual
DESCRIPTION
PSV 2465-40 is an up-to date power supply unit with battery
backup compliant with EN standards. Unit provides all features
required by EN 50131-6:2008+A1:2014, security
Distinctive and unique feature of PSV 2465-40 is invented by
Alarmtech ViP mode – Voltage-in-Parallel. Power supply units
with ViP feature can be connected in parallel both (+) and (-) on
one common power bus without a need of additional synchroni-
zation. Connected units will share load on a bus. ViP feature can
be used to build distributed and redundant power systems. It can
be also used to compensate voltage drops on a bus by placing
power supply units in distant bus sections.
Power conversion is based on high frequency SMPS regulator
providing high conversion efficiency. Low losses inside unit pre-
serve batteries from overheating shortening battery life time.
Computerized battery recharging circuit works in constant poten-
tial – limited current mode – the best mode to provide the longest
possible battery life time.
Power unit is equipped with built-in diagnostic system detecting
and signalling mains failure, different battery failures including
end-of-life warning, output faults like low voltage or broken fuse.
APPLICATIONS
 Power supply system for 24 V installations
 Distributed power supply systems with built-in redundancy
 Power supply systems for access control, fire and intruder
alarm installations
BLOCK DIAGRAM
230 VAC
L
PE
N
© 2016 Alarmtech – www.alarmtech.se
Power Supplies
grade 3
Signalling outputs
EPS, APS, OUT, SAB, SDT
Power supply unit
PSV-2465
SMPS w. LLC controller
ViP mode, security grade 3
12V battery
12V battery
40 Ah
MAIN FEATURES
 Security grade 3 (EN 50131-6:2008+A1:2014)
 Type A – mains supply with rechargeable battery
 Basic parameters in grade 3 (default):
.
 Total rated output: 1 A
(30 h in battery mode with 40 Ah batteries)
 Battery recharging current: 1.5 A
(providing recharging time below 24 h)
 Total rated maximal output to installation: 5 A
 Basic parameters in grade 2:
(PSV-2465-40 can be downgraded from default grade 3 to
grade 2 with the help of PSVlink software)
 Total rated output: 2.6 A
(12 h in battery mode with 40 Ah batteries)
 Battery recharging current: 0.5 A
(providing recharging time below 72 h)
 Total rated maximal output to installation: 6 A
 Total current capacity of power unit – 27.6V, 6.5 A
 ViP (Voltage-in-Parallel) feature increasing reliability and ca-
pacity of power supply systems – power supplies with ViP fea-
ture can be connected in parallel to same bus without need
for additional synchronization
 Capable to work with pack of two 12 V/40 Ah sealed lead acid
batteries
 Short circuit and overload protection
 Detection of no mains supply (EPS fault)
 Detection of different battery faults (APS fault) – not con-
nected, low voltage, high internal resistance
 Detection of low output voltage (OUT fault)
 Detection and LED identification of broken fuses
 Detection of power unit failure
 Deep discharge protection of battery (DDP)
 Remote and local battery testing
 Tamper security provided – case opening and pry-off
 Optional Fuse Card with 6 fused outputs and Ground Fault
Detector (model PSV FC24-6)
Remote battery
test
Front panel
24 VDC output
EPS – External Power Supply (mains)
APS – Alternative Power Source (battery)
OUT - Output voltage
SAB – Sabotage
40 Ah
SDT – Storage Device (battery) Test
1 / 4
Battery 40 Ah/Security grade 3
Optional Fuse Card
Signalling outputs PSV FC24-6
6 fused
Fuse Card
output
PSV FC24-6
channels
PE
PSV 2650-40 manual 1636en
24 VDC/6.5 A
PSV 2465-40