Page 2
NAUTICAST B2 hardware and software may be upgraded from time to time and future versions of the NAUTICAST B2 may therefore not correspond exactly with this manual. When necessary, upgrades to the product will be accompanied by updates or addendums to this manual.
Index WHAT IS AIS? ..............................5 AIS C ................................6 LASSES ..........................7 OSITION NFORMATION OURCE INSTALLATION ..............................7 ............................. 7 HE CONTENTS OF THIS BOX ............................8 OFTWARE REREQUISITES ............................8 OFTWARE NSTALLATION ..............................8 ROGRAMMING ..................................9 ..........................10 OFTWARE ONFIGURATION .............................
Page 4
History of Changes Date Version Status Comments Responsible 2013-07-31 1.14 Release First Official Release Ch. Aschl Software dependencies This revision of the Manual is valid for the Software version (s) below stated and future versions unless otherwise noted (ref.: www.1st-relief.com). Date AIS software Version Status Comments...
WHAT IS AIS? AIS stands for Automatic Identification System. AIS increases navigational safety and collision avoidance by transmitting vessel identification, helping to reduce the difficulty of identifying ships when not in sight (e.g. at night, in radar blind arcs or shadows or at distance) by broadcasting navigational intentions to other vessels by providing ID, position, course, speed and other ship data with all other nearby ships and land based stations.
On the bottom, a typical NAUTICAST B2 installation in a common environment is shown. The NAUTICAST B2 is connected to the vessels power supply, and in connection with the VHF, and GPS-Antennas, the minimal requirements for Transponder operation are fulfilled.
AIS unit and thus the vessel to which it is fitted. The NAUTICAST B2 utilizes the GPS satellite network. Installation The contents of this box Before proceeding with the installation of the Nauticast B2, please check the contents of the box, which should include: The Nauticast B2 AIS transponder ...
'Link2AIS'. This short cut should be used to launch the application as required. Programming NOTE: To program your NAUTICAST B2 you will need to connect the AIS to a personal computer or Laptop with Link2AIS software installed. There is no external power source needed when using a USB connection.
Start the Link2AIS software program on PC. The application requires a USB connection to a NAUTICAST B2 transponder. The connection status is indicated in the lower left corner of the Link2AIS window: Open the connection settings: ...
Software Configuration The functions of Link2AIS are arranged in a series of tabs. Each tab contains information relating to a particular aspect of the connected AIS transponder. Depending on the version of Link2AIS installed not all tabs shown below may be visible.
Page 11
Enter the vessels information in the appropriate box: MMSI number - enter the vessel's Maritime Mobile Service Identity number Call Sign - enter the vessel's radio call sign (7 characters maximum) Ship's name - enter the name of the vessel (20 characters maximum) ...
WARNING: Do not connect the NAUTICAST B2 unit to a main (line) AC electrical supply, as it could cause electric shock or fire. Length of Data/Power Cable connection must not exceed 3 meters.
This is a TNC female bulkhead connector that mounts to the back of the case. This port provides the 5V DC feed for the active GPS antenna required by the NAUTICAST B2 unit (i.e. it should incorporate an LNA) and must be suitable for marine shipboard applications (index of protection, ruggedness, means of mounting, etc.).
Using the transponder Status LEDs 3.1.1 Power OK A green LED illuminates to show that the unit is connected to an external power source and is operating. 3.1.2 TX Timeout An amber LED illuminates if the unit has failed to transmit a position report during the last two reporting intervals.
For more information about the used interface protocol refer to the latest “PROTOCOL SPECIFICATION” of the Nauticast B2 or contact our Technical Support Team (see Section: Contact & Support information).
“Protected” according to IEC 60945-Ed.4 Compass Safe Distance 0,55m Information Reporting Intervals The Nauticast Class-B AIS will transmit position reports (Message 18) in reporting intervals Every 30 seconds if SOG is > 2 kn; Every 3 Minutes if SOG is < 2 kn Provided that the transmission time periods are available.
1st-Relief GmbH device or system. If these fail, it is reasonable to assume that the safety of the user or other persons may be endangered. Contact your local dealer for NAUTICAST B2 support. Please see our 1st-Relief GmbH Website for Dealer / Service Listing.
Appendix APPENDIX A System Block Diagram Power supply, PC, NMEA compatible devices not included Data Cable optional (Mount unit with cable side down) page 19 of 26 1st3001001 EN 1_14.docx -Relief GmbH Bank: UniCredit Bank Austria AG FN: 206478w, HG Wien Handelskai 388 / Top 632 Swift/BIC: BKAUATWW VAT No.: ATU 51115305...
Page 20
APPENDIX B Class-B POWER CABLE Description Wire Type Color 10VDC-32VDC + Copper Copper BLACK DATA CABLE Class-B Description DB15 Wire Type Color CABLE # RS422 TX A Copper YELLOW CABLE 1 RS422 TX B Copper GREEN CABLE 1 RS422 RX A Copper WHITE CABLE 1...
Page 21
Use of the Data Cable CABLE 1: Connect the according cable ends to the designated NMEA 0183 device. Wire end Nauticast B2 Possible end of attached NMEA device RS422 TX A, yellow connect to RX A (+) RS422 TX B, green...
Page 22
The input voltage of the alarm relay is matched with the operating voltage of the Nauticast B2. The operating voltage of the alarm relay is 3 to 60 VDC with a load current of 0.1 to 2 A (3A when using a heat sink).
Page 23
CABLE 4: Depending on the Voltage used for the Nauticast B2 you have to calculate the series resistor which is connected with the LED between the + wire (grey) and the OUTPUT wire (CH1 LED RED, green; CH2 LED RED, brown; TX TIMEOUT LED, white; ERROR LED, yellow). A series resistor of 330...
Page 24
APPENDIX C Appendix D page 24 of 26 1st3001001 EN 1_14.docx -Relief GmbH Bank: UniCredit Bank Austria AG FN: 206478w, HG Wien Handelskai 388 / Top 632 Swift/BIC: BKAUATWW VAT No.: ATU 51115305 1020 Vienna, Austria, Europe IBAN: AT24 1100 0085 7396 5400 Tax No.
Page 25
Appendix E page 25 of 26 1st3001001 EN 1_14.docx -Relief GmbH Bank: UniCredit Bank Austria AG FN: 206478w, HG Wien Handelskai 388 / Top 632 Swift/BIC: BKAUATWW VAT No.: ATU 51115305 1020 Vienna, Austria, Europe IBAN: AT24 1100 0085 7396 5400 Tax No.