Table of Contents
Advertisement
Quick Links
FCC Certifications
This Equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received; including interference that may cause undesired
operation.
CE Mark Warning
This equipment complies with the requirements relating to electromagnetic compatibility,
EN 55022 class A for ITE, the essential protection requirement of Council Directive
89/336/EEC on the approximation of the laws of the Member States relating to
electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be possible that
information in this document is not up-to-date. Please check with your local distributors
for the latest information. No part of this document can be copied or reproduced in any
form without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective companies.
Copyright © 2003, All Rights Reserved.
Document Version: 2.0
Advertisement
Table of Contents
Related Manuals for Longshine LCS-883R-SW2402
Summary of Contents for Longshine LCS-883R-SW2402
-
Page 1: Fcc Certifications
FCC Certifications This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. - Page 2 Introduction The device is a powerful, high-performance Gigabit Ethernet switch, which provides smart and efficient management functions and supports 26 ports connection, where 24 ports of them are capable of 10/100Mbps and 2 ports capable of 10/100/1000Mbps with Full/Half duplex capability. This switch supports various port administrations including speed/duplex/flow control, ports trunk (port aggregation), port-based / 802.1Q VLAN configurations, bandwidth control features, port mirroring functions and also some easy miscellaneous...
-
Page 3: Status Operation
LED Definition Please refer to the following table for LED definition Type Status Operation System Power Steady Green Power is on Power is off Status Steady Green Power on diagnostics testing Power on diagnostics test successful Blinking Green Power on diagnostics test fail Port 1~24 100M Steady Green... -
Page 4: Cable Selection
Installation AC Power The switch’s power supply automatically adjusts to line power in the range 100~240 VAC and 50~60 Hz. Cable Selection The switch can use the following types of cabling: 10BASE-T: Category 3, 4 or 5 UTP/STP 100BASE-TX: Category 5 UTP/STP 1000BASE-T: Category 5 UTP/STP Category 5 or enhanced cable is preferred to use with this product in structured wiring environments. -
Page 5: Vlan Configuration
Console Program Main menu Press [Enter] key and input username and password to login to the console, (default username / password admin / admin) then the Main Menu displays as shown as below: This powerful 24+2 Gigabit Smart Switch provides the following management function: Function Statement Port Configuration and Status... - Page 6 Ports Configuration and Status The [Ports Configuration and Status] menu includes: Port speed and duplex mode setting: 10/100Mbps, Full/Half duplex mode and auto-negotiation Bandwidth control: 10%~100% Flow control: enable/disable You could change the default setting by the function key For example: If you want to set port 5 to 10Half and let flow control enable, meanwhile, limit the bandwidth to the 60% of current connecting speed, please follow the directions listed as below: Move the cursor to port 5 “Speed/Duplex”...
-
Page 7: Port-Based Vlan
Port-Based VLAN You can select some ports into the same VLAN group by symbol “ ”. If the packets come into one port, which only belongs to one VLAN group, the packets just can be forwarded to another ports of this VLAN group. For Example: When one packet comes into port 1 or port 3, the packet could be forward to VLAN 1 and VLAN 6. - Page 8 For example: The two figures describe… When one packet with VLAN tag “6” comes into port 5, the packet will be forwarded to VLAN ID “6” group. The member ports of VID 6 (port 7, 8, 9, 13, 15, 19, 23) will receive this packet When one packet with VLAN tag “6”...
- Page 9 The ports at both ends of a Ports Trunk connection must have the same port properties, including Speed, Duplex mode Ports Mirroring Configuration The 24+2 Gigabit Smart Switch provides Ports Mirroring Configuration to snoop a specified port. Setup a Monitored port; the packets will be duplicated to the Monitoring port. Miscellaneous This Miscellaneous setting includes the Version Information, Change Username / Password, Save Current Configuration and Reset to Default Settings.
- Page 10 Version Information You can read the hardware version, software version, and key chipset version. It may be possible that information in this screen is not up-to-date Change Username / Password The factory default value of username / password is admin / admin.
- Page 11 Network Application...
-
Page 12: Cable Connections
Specifications Standard IEEE802.3, IEEE802.3u, IEEE802.3x, IEEE802.3ab, IEEE802.3ad, IEEE802.1Q Interface 24 * 10/100Mbps RJ-45 ports 2 * 10/100/1000Mbps RJ-45 ports (Auto MDI/MDI-X) RJ-45 (10BASE-T): Category 3,4,5 UTP/STP Cable Connections RJ-45 (100BASE-TX): Category 5 UTP/STP RJ-45 (1000BASE-T): Category 5 UTP/STP Network Data Rate 10/100/1000Mbps Transmission Mode 10Mbps... -
Page 13: Declaration Of Conformity
61LS-5526C-200 DECLARATION OF CONFORMITY CE = European Community Conformity Mark We, Manufacturer/Importer Longshine Technologie (Europe) GmbH An der Strusbek 9 22926 Ahrensburg Germany Declare That The Product LCS-883R-SW2402 24 x 10/100 Mbps + 2 x 1000Base-TX Gigabit Switch Is In Conformity With:... - Page 14 Date: 18.09.2002...