1. Manuals
  2. Brands
  3. Longshine Manuals
  4. Switch
  5. LCS-GS-9316
  6. Installation and use manual

Longshine LCS-GS-9316 Installation And Use Manual

16-port gigabit ethernet web based smart switch
Hide thumbs
Table of Contents

Advertisement

Quick Links

Longshine Technologie Europe GmbH
www.longshine.de

Advertisement

Table of Contents
loading

Related Manuals for Longshine LCS-GS-9316

Summary of Contents for Longshine LCS-GS-9316

  • Page 1 Longshine Technologie Europe GmbH www.longshine.de...

  • Page 2: Fcc Certifications

    FCC Certifications This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
  • Page 3 Table of Contents UNPACKING INFORMATION ..............4 1. INTRODUCTION TO 16/24-PORT GIGABIT WEB SMART SWITCH ......................5 1.1 G ..................5 ENERAL ESCRIPTION 1.2 K ....................6 EATURES 1.3 T ..................7 RONT ANEL 1.4 T ...................8 ANEL 2. INSTALLING 16/24 GIGABIT WEB SMART SWITCH ....9 2.1 D ..................9...
  • Page 4 4.2.7 Statistics ....................26 4.2.8 Discovery ...................27 4.2.9 Default ....................28 4.2.10 Reboot .....................28 5. PRODUCT SPECIFICATIONS ............29 6. APPENDIX ....................30 6.1 C ................30 OMMAND NTERFACE 6.1.1 Start-up and Terminal configuration ............30 6.1.2 General....................30 6.1.2.1 Login/Logout Procedures ..............30 6.1.2.2 Command Hierarchy.................30 6.1.2.3 Help Utility ..................31 6.1.2.4 Entering Commands.................32 6.1.2.5 Terminology..................33 6.1.3 Command Description .................34...

  • Page 5: Unpacking Information

    Unpacking Information Thank you for purchasing the 16/24-port Gigabit Web Smart Switch. Before you start, please check all the contents of this package. The product package should include the following: 1. One 16/ 24-port Gigabit Web Smart Switch 2. One power cord 3.

  • Page 6: Introduction To 16/24-Port Gigabit Web Smart Switch

    1. Introduction to 16/24-port Gigabit Web Smart Switch 1.1 General Description The device is a 16/24-port 10/100/1000Mbps Ethernet Web Smart Switch. Compare to the traditional 10/100Mbps Ethernet, the switch delivers a dedicated Gigabit connection to every attached client with no congestion issue. The gigabit ports also provide the fat pipe to the server or backbone connectivity for boosting the total system performance.

  • Page 7: Key Feature

    1.2 Key Features Complies with 10BASE-T specifications of the IEEE802.3 standard Complies with 100BASE-TX specifications of the IEEE802.3u standard Complies with 1000BASE-T specifications of the IEEE802.3ab standard 16/ 24 10/100/1000Mbps Ethernet ports for easy network connecting application. Supports NWay protocol for speed (10/100/1000Mbps) and duplex mode (Half/Full) auto-detection Provide Auto-discovery Function for easy Network management.

  • Page 8: The Front Panel

    1.3 The Front Panel The front panel of the switch is shown as below 16-ports 24-ports Port Operation There are 16/ 24 * 1000Mbps RJ-45 (copper) ports on the front panel. The auto-negotiation feature of the switch allows each port of the device running at one of the following operation modes: Speed Duplex Mode...

  • Page 9: The Rear Panel

    LEDs Definition The rich diagnostic LEDs on the front panel can provide the operating status of individual port and whole system. Power LED This indicator lights green when the switch is receiving power; otherwise, it is off. Port LEDs Every RJ-45 port on the front panel relevant two LEDs (10/100M; 1000Mbps) for indicating the connection speed and activity status.

  • Page 10: Installing 16/24 Gigabit Web Smart Switch

    2. Installing 16/24 Gigabit Web Smart Switch This switch can be placed directly on your desktop, or mounted in a rack. Users can immediately use most of the features simply by attaching the cables and turning the power on. 2.1 Desktop Installation For desktop installation, the switch needs to put on a clean, flat desk or table close to a power outlet.

  • Page 11: I Nstalling N Etwork C Ables

    2.3 Installing Network Cables Station Connections Reference to the wiring statement of the previous section; connect each station to the switch with correct type of cables. Switch-to-Switch Connections In making a switch-to-switch connection, use every ports to connect another switch or backbone is strongly recommended.

  • Page 12: Functional Description

    3. Functional Description 3.1 PHY Monitoring and Port Mode Set-up It is a major task of the software to continuously monitor the PHYs in order to set up the switch ports according to whether the link is down or up and in the latter case what the current speed, duplex mode and pause capabilities are.

  • Page 13: L Ink A Ggregation

    3.5 Link Aggregation Link aggregation groups (or channels) can be defined statically. LACP (Link Aggregation Control Protocol) is not supported. Maximum number of aggregation groups is 8. The software will automatically detect that a link has gone down and then reassign packet distribution on the other links in the group.

  • Page 14: Management Guide

    4. Management guide This section instructs you how to enter and set up the configurations, which can be accessed by RS-232 serial port (out-of-band) on the rear panel or by Internet Browser over the network (in-band). Factory Default value: 192.168.1.1 ：...
  • Page 15 In-Band Connections (Web Browser) To manage the switch through in-band access, you should configure the management station with an IP address and subnet mask compatible with your switch. 1. Running your Web Browser and enter the IP address “192.168.1.1” as the URL in the “address”...

  • Page 16: Home Page

    4.2 Home Page On the Home page, you can select the configuration by clicking the menu tabs located on the upside of the UI. It includes, System Ports VLANS Aggregation Mirror Statistics Discovery Tabs of configuration Port detail Statistics...
  • Page 17 To restore the default Values of switch, Click the “Default” Button. If you want to reboot the switch, click the “Reboot” Button. To check the connection status of each port from 1 to 16(16-ports) /24(24-ports), take a look at the port monitor. When the port shows green, it connected.

  • Page 18: System

    4.2.1 System To set up the system configurations such as login value, time-out value and enabling the VLAN Management. Items Functions Mac Address The Mac Address of the switch S/W Version To check up the Software Version, see this. H/W Version The Hardware version Inactivity Timeout Set the console inactivity timeout in...
  • Page 19 Note. After you change the IP address, the switch will reboot itself. You may click the new address to link the New IP with your Browser.

  • Page 20: Ports

    4.2.2 Ports On the page, you can view the Port status, set up the Speed mode and enable the FDX flow control. Items Functions Link To show the status of each port. When it’s red, it means the connection is down. Otherwise, it’s green.

  • Page 21: Vlans

    4.2.3 VLANS VLANS Configuration is for dividing the LAN into subnet groups for better network management. The benefit is that the user can move one client to another subnet group without actually moving the machine. There are 16(16-ports) /24(24-ports) entries to set To add new VLAN Entry, 1.
  • Page 22 PVID When the VLAN-enabled switch receives a tagged packet, the packet will be sent to the port’s default VLAN according to the PVID (port VLAN ID) of the receiving port. Items Functions Port Port Number 1~16(16-ports) /24(24-ports) PVID Port VLAN ID(1~4094) Aware Check the “Aware”...

  • Page 23: Aggregation/ Trunking Configuration

    4.2.4 Aggregation/ Trunking Configuration To set up the Port trunk groups, put the ports number into the same Aggregation group line. There are eight groups to choose. Don’t forget to click the “Apply” to save the setting. The maximum of ports for one group is 8. There three aggregation modes for you to setup, SMAC (Source MAC), DMAC (Destination MAC), and XOR.

  • Page 24: Quality Of Service (Qos) Tos Configuration

    4.2.5 Qos There are four modes of Quality of Service to choose, custom TOS, Custom Shaper, Custom Policer, and Custom Storm. 4.2.5.1 Quality of Service (QoS) TOS Configuration To improve the network performance by applying the TOS, set up the priority of eight groups of precedence bits on this page.

  • Page 25: Qos Port's Shaper

    4.2.5.2 QoS Port’s shaper To limit the total out-going packet rate, select enable and enter the Value you need from 250~1000000K bps. Any packet rate that is larger than the limitation will be discarded. Don’t forget to click apply to save.

  • Page 26: Qos Port Policer

    4.2.5.3 QoS Port Policer To limit the total In-coming packet rate, select enable and enter the Value you need from 250~1000000K bps. If the packet rate that is larger than the limitation, the switch will make the associated client to suspend the frame transmission by using backpressure or pause frame.

  • Page 27: Mirror

    4.2.6 Mirror Port mirror is used to mirror traffic from source port to a target port for analysis. Only 2 ports can be monitored (mirrored) simultaneously to 1 Monitor port (target port). (Note that the target port must be in the same VLAN as the source port) Items Functions Monitor Port Select the switch port, from 1 to 16(16-ports)/...

  • Page 28: Discovery

    4.2.8 Discovery When you install several our 16port and 24port gigabit web-smart switches, the discovery management tool helps you to search and access those switches on the LAN easily. Therefore you can access any switch on your LAN without memorizing those IP addresses.

  • Page 29: Default

    4.2.9 Default To restore to default values, 1. Click the default button on the Home page 2. Click “Yes” to enact. Don’t power off the switch while it’s work. 4.2.10 Reboot To reboot the switch, 1. Click the Reboot button on the Home page 2.

  • Page 30: Product Specifications

    5. Product Specifications Standard IEEE802.3 10BASE-T IEEE802.3u 100BASE-TX IEEE802.3x full-duplex operation and flow control IEEE802.3ab 1000BASE-T IEEE802.1Q VLAN interoperability Interface * 10/100/1000Mbps auto 16(16-ports) /24(24-ports) MDI/MDI-X RJ-45 switching ports 1 * RS-232 Console port Cable Connections RJ-45 (10BASE-T): Category 3,4,5 UTP/STP RJ-45 (100BASE-TX): Category 5 UTP/STP RJ-45 (1000BASE-T): Category 5,5e or enhanced UTP/STP...

  • Page 31: Appendix

    6. Appendix 6.1 Command Line Interface 6.1.1 Start-up and Terminal configuration To start-up the command line interface, please connect a PC COM port to the RS-232 connector and activate a terminal emulation software (e.g. HyperTerminal of Windows.) The terminal emulation software should be set up as follows: Data rate: 115200 baud Data format: 8 data bits, 1 stop bit and no parity Flow control: none.

  • Page 32: Help Utility

    To be at top level, you may enter up at any level. (ex, system>up <enter>) The current level and group is indicated by the prompt. If you are at the top level, the prompt will be:> Note: all the characters entered in the command line interface are NOT case-sensitive. 6.1.2.3 Help Utility You can get command information by entering ? or help.

  • Page 33: Entering Commands

    6.1.2.4 Entering Commands Commands are given by entering the command string. You can get those commands syntax by the help utility we referred to last chapter. Characters are not case-sensitive in the command string. (Ex, for the command syntax “System Configuration [all]”, it makes no difference entering “System Configuration”...

  • Page 34: Terminology

    6.1.2.5 Terminology The following table shows general parameter types used in command syntaxes and descriptions. <port> The port number <portlist> Comma and/or dash separated port list. This type can be used for specifying individual ports or a range of ports. The keyword ‘none’ can be used to specify an empty port list.

  • Page 35: Command Description

    6.1.3 Command Description In this session, the commands in each group and the descriptions to those commands are provided respectively in the following group order: 1.System 2.Console 3.Port 4.MAC 5.VLAN 6.Aggregation 7.QoS 8.Mirror 9.IP 6.1.3.1 System Commands Commands at the System level: System Configuration [all] System Restore default [keepip] System UserName [<name>]...

  • Page 36: Console Commands

    Set or show the password. The password can not be empty. [<password>]: Password string of up to 16 characters . Note: If you like to leave your password as blank, enter "" as the password string 5. Systemname Syntax: Systemname [<systemname>] Description: Set or show the system name.

  • Page 37: Port Commands

    6.1.3.3 Port Commands Commands at Port level: Port Configuration [<portlist>] Port Mode [<portlist>] [<mode>] Port Flow Control [<portlist>] [enable|disable] Port State [<portlist>] [enable|disable] Port MaxFrame [<portlist>] [<framesize>|reset] Port Statistics [<portlist>] [clear] 1. Port Configuration Syntax: Port Configuration [<portlist>] Description: Show the configured and current speed, duplex mode, flow control mode and state for the port. <portlist>: Port list (Default: All ports).

  • Page 38: Mac Table Commands

    5. Port MaxFrame Syntax: Port MaxFrame [<portlist>] [<framesize>|reset] Description: Set or show the maximum frame size in bytes (including FCS) for frames received on the port. Tagged frames are allowed to be 4 bytes longer than the maximum frame size. Use the reset option to return to the default setting.

  • Page 39: Vlan Commands

    Delete MAC address and VLAN ID. <macaddress>: MAC address, 12-digit hex string, optionally separated with dashes or colons (e.g. 010203ABCDEF or 01-02-03-AB-CD-EF or 01:02:03:AB:CD:EF). [<vid>] : VLAN ID (default: 1). 4. MAC Lookup Syntax: MAC Lookup <macaddress> [<vid>] Description: Lookup MAC address and VLAN ID. <macaddress>: MAC address, 12-digit hex string, optionally separated with dashes or colons (e.g.
  • Page 40 Description: Add VLAN entry and include ports in member set. <vidlist> : VLAN ID list. [<portlist>]: Port list (default: All ports). 3. VLAN Delete Syntax: VLAN Delete <vidlist> Description: Delete VLAN entry (all ports excluded from member set). <vidlist> : VLAN ID list. 4.

  • Page 41: Aggregation/Trunking Commands

    6.1.3.6 Aggregation/trunking Commands Commands at Aggr level: Aggr Configuration Aggr Add <portlist> Aggr Delete <portlist> Aggr Lookup <portlist> Aggr Mode [smac|dmac|xor] 1. Aggregation Configuration Syntax: Aggr Configuration Description: Shows the aggregation groups and the aggregation mode. 2. Aggregation Add Syntax: Aggr Add <portlist>...

  • Page 42: Qos Commands

    6.1.3.7 QoS Commands Commands at QoS level: QoS Configuration [<portlist>] QoS TosPrecedence [<portlist>] [<tosprecedencelist>] [low|high] QoS Shaper [<portlist>] [enable|disable] [<rate>] QoS Policer [<portlist>] [enable|disable] [<rate>] QoS Storm Control [<portlist>] [enable|disable] [<rate>] 1. QoS Configuration Syntax: QoS Configuration [<portlist>] Description: Show the configured IP ToS Precedence priority mapping, shaper configuration, policer configuration and multicast storm control [<portlist>]: Port list (default: All ports).

  • Page 43: Mirror Commands

    5. QoS Storm Control Syntax: QoS Storm Control [<portlist>] [enable|disable] [<rate>] Description: Set or show the multicast storm control configuration. Multicasts and broadcasts are controlled using a multicast policer. [<portlist>] : Port list (default: All ports). [enable|disable]: Enable/disable the multicast policer (default: Show multicast policer mode).

  • Page 44: Ip Commands

    6.1.3.9 IP Commands Commands at IP level: IP Configuration IP Setup [<ipaddress> [<ipmask> [<ipgateway>]]] 1. IP Configuration Syntax IP Configuration Description: Show the IP status, including IP, Subnet Mask, and Default Gateway 2. IP Setup Syntax IP Setup [<ipaddress> [<ipmask> [<ipgateway>]]] Description: Set the IP, Subnet Mask, and Default Gateway...

  • Page 45: Example

    6.1.4 Example 6.1.4.1 VLAN configuration This example shows how to configure two VLANs with the following setup: ‧ VID 1 spans ports 2-16 and VID 2 spans ports 1-3, so port 2 and 3 are members of both VLANs and all 16 ports must be VLAN aware. ‧...

  • Page 46: Factory Default Configuration

    6.1.5 Factory Default Configuration The factory default configuration is a VLAN unaware L2 switch with automatic learning/ageing and auto negotiation enabled on all ports: ‧ System: The system name string is empty. ‧ Console: The password string is empty and inactivity timeout is disabled. The prompt is “>”. ‧...
  • Page 47 DECLARATION OF CONFORMITY CE = European Community Conformity Mark We, Manufacturer/Importer Longshine Technologie (Europe) GmbH An der Strusbek 9 22926 Ahrensburg Germany Declare That The Product LCS-GS-9316 16-Port Gigabit Ethernet Web Based Smart Switch Rackmount Is In Conformity With: Standards...
  • Page 48 DECLARATION OF CONFORMITY CE = European Community Conformity Mark We, Manufacturer/Importer Longshine Technologie (Europe) GmbH An der Strusbek 9 22926 Ahrensburg Germany Declare That The Product LCS-GS-9324 24-Port Gigabit Ethernet Web Based Smart Switch Rackmount Is In Conformity With: Standards...

Table of Contents