Advertisement

Quick Links

FCC Certifications
This Equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to
provide
reasonable
protection
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will
be required to correct the interference at his own
expense.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2)
this device must accept any interference received;
including
interference
that
operation.
CE Mark Warning
This equipment complies with the requirements relating to
electromagnetic compatibility, EN 55022 class A for ITE,
the essential protection requirement of Council Directive
2004/108/EC on the approximation of the laws of the
Member States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its
products and it may be possible that information in this
document is not up-to-date. Please check with your local
distributors for the latest information. No part of this
document can be copied or reproduced in any form
without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of
their respective companies.
Copyright © 2011, All Rights Reserved.
1
against
harmful
may
cause
undesired

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LCS-GS9116 and is the answer not in the manual?

Questions and answers

Summary of Contents for Longshine LCS-GS9116

  • Page 1 FCC Certifications This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
  • Page 2: Unpacking Information

    Unpacking Information Thank you for purchasing this product. Before installation, please verify that your package contains the following items. 1. 16-port gigabit switch*1(16-port) 24-port gigabit switch*1(24-port) 2. AC power cord*1 3. Rubber foot*4 and screws 4. 19’L bracket *2 5. User manual*1 Introduction The device is a powerful and high-performance Gigabit Ethernet switch with 16 (...
  • Page 3: Key Features

    Key Features Complies with 10 BASE-T specifications of the IEEE802.3 standard Complies with 100BASE-TX specifications of the IEEE802.3u standard Complies with 1000BASE-T specifications of the IEEE802.3ab standard Supports back-pressure (half duplex) and flow control (IEEE 802.3x) Supports NWay protocol for speed (10/100/1000Mbps) and duplex mode(Half/Full) auto-detection Supports MDI/MDI-X auto crossover and polarity...
  • Page 4: Front Panel

    Front Panel The front panel consists of LED indicators and the ports. 16-port 19-inch Model 24-port 19-inch Model LEDs Definition: This switch contains LEDs to show the activities and information of the ports, including power LED and Link/Act LEDs. Status Operation Steady Green The switch is powered on...
  • Page 5: Rear Panel

    Rear Panel The back is shown as bellow (contains a three pronged outlet). Power Receptacle To be compatible with the electric service standards around the world, the switch is designed to afford the power supply in the range from 100 to 240VAC, 50/60Hz. Please make sure that your outlet standard is within this range.
  • Page 6: Network Cables

    3. Plug the switch with the female end of the provided power cord and plug the male end to the power outlet. Rack-mount Installation The switch can be mounted in a standard 19” rack with two optional rack mounting brackets and screws, which are used for rack mounting the unit.
  • Page 7: Network Application

    Speed Media Wiring (Mbps) Category3,4,5 UTP/STP 10/100/1000Mbps Category 5 UTP/STP copper 1000 Category5,5e UTP/STP [Tips:] To performing this switch well, we strongly recommend below installation environment: 1. The switch is placed with appropriate ventilation environment. A minimum 25mm space around the unit is recommended.
  • Page 8: Product Specifications

    Product Specifications IEEE802.3 (10BASE-T) IEEE802.3u (100BASE-TX) Standard IEEE802.3ab (1000BASE-T) IEEE802.3x full-duplex flow control 24 10/100/1000Mbps RJ-45 ports(16-port) Interface 24 10/100/1000Mbps RJ-45 ports(24-port) RJ-45 (10BASE-T): Category 3,4,5 UTP/STP Cable RJ-45 (100BASE-TX): Category 5 UTP/STP Connections RJ-45 (1000BASE-T): Category 5,5e or enhanced UTP/STP Network 10/100/1000 Mbps Auto-negotiation Data Rate...
  • Page 9 DECLARATION OF CONFORMITY In accordance to EUROPEAN COUNCIL DIRECTIVE 2004/108/EWG = European Community Conformity Mark We, Manufact rer/Importer Longshine Technologie (Europe) GmbH An der Strusbek 9 22926 Ahrensburg Germany Declare That The Product LCS-GS9116-A 16 Port Gigabit Switch Is In Conformity With:...
  • Page 10 DECLARATION OF CONFORMITY In accordance to EUROPEAN COUNCIL DIRECTIVE 2004/108/EWG = European Community Conformity Mark We, Manufact rer/Importer Longshine Technologie (Europe) GmbH An der Strusbek 9 22926 Ahrensburg Germany Declare That The Product LCS-GS9124-A 24 Port Gigabit Switch Is In Conformity With:...

This manual is also suitable for:

Lcs-gs9124

Table of Contents