Advertisement

Instructions
GB
-
Instrucțiuni de utilizare - RO
Anleitung - D
Eredeti használati utasítás - HU
Ръководство за употреба - BG
Instrukcja obsługi - PL
www.heinner.com
VDE003

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VDE003 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Heinner VDE003

  • Page 1 Instructions Instrucțiuni de utilizare - RO Anleitung - D Eredeti használati utasítás - HU Ръководство за употреба - BG Instrukcja obsługi - PL www.heinner.com VDE003...
  • Page 2 ELECTRIC CHAIN SAW Thank you for choosing Heinner! max. min.
  • Page 3 ELECTRIC CHAIN SAW 2/10 sec. Pulling Extrusion force force Pulling force Extrusion Pulling force Extrusion force force Intended falling direction Top of falling notching Falling notching pitch is about 30° to 45° Falling cross section Bottom of falling notching is Fracture zone is at least 1/10 of at least 1/3 to 1/5 of the the master diameter of the tree.
  • Page 4: Pictogram Illustration And Explanation

    ELECTRIC CHAIN SAW PICTOGRAM ILLUSTRATION AND EXPLANATION Warning! Unplug immediately if the power cord or plug becomes damaged! Protect from the damp. Read the operation manual and follow the warnings and safety instructions! Wear protective helmet, goggles and earmuffs! Always pull the plug out of the power socket before doing any work on the chainsaw! Always keep the children and bystanders away from the working area.
  • Page 5 ELECTRIC CHAIN SAW • Never expose the chainsaw to rain or bad weather. Make sure there is enough light at the place of work. Do not use power tools in the vicinity of combustible liquids or gases. • If the chainsaw is not being used for a while, it must be set aside in such a way that no other person is endangered.
  • Page 6: Before Starting Up

    ELECTRIC CHAIN SAW • Make sure that the saw chain is always properly sharpened. • Never cut through more than one branch at a time! When lopping off branches, be careful not to touch any other branches. • When cross-cutting, pay attention to trunks standing very close to each other. If possible use a saw-horse. Transporting the chainsaw Before transporting the chainsaw, always remove the plug from the power socket and slide the chain guard over the rail and chain.
  • Page 7 ELECTRIC CHAIN SAW Chain lubrication To prevent excessive wear, the saw chain and guide bar must be evenly lubricated during operation. Lubrication is automatic. Never work without chain lubrication. If the chain runs dry, the entire cutting apparatus will quickly become severely damaged. It is therefore important to check both chain lubrication and the oil gauge every use (Fig.
  • Page 8 ELECTRIC CHAIN SAW chain guard. Chainsaw protection Never use the chainsaw in the rain or in damp conditions. If the extension cable is damaged, pull the plug out of the power socket immediately. Never work with a damaged cable. Check the chainsaw for damage. Before using your tool again, check the safety devices or any slightly damaged parts to ensure that they are in good working order.
  • Page 9: Maintenance And Cleaning

    Check the chain tension difficulty Chain jumps off sword Chain becomes hot Chain lubrication Check oil level Chain lubrication TECHNICAL DATA Model number VDE003 Rated voltage (V) 230-240V~ 50Hz Rated power (W) 2200 Blade length (mm) 405mm Cutting length(mm) 385mm...
  • Page 10 ELECTRIC CHAIN SAW RECYCLING Electrical and electronic equipment waste (DEEE) might contain dangerous materials which can have a negative impact on the environment and human health if not collected separately. This item is in conformity with the European Directive EU DEEE (2012/19/EU) and is marked with an electronic and electrical waste logo graphically represented in the image below.

Table of Contents