Using Service Request (Srq) And Serial Poll - HP E3633A User Manual

Chapter 4 Remote Interface Reference
The SCPI Status Registers
The Status Byte Summary register is cleared when:
‡ <RX#H[HFXWH#WKH#*CLS#+FOHDU#VWDWXV,#FRPPDQG1
‡ 4XHU\LQJ#WKH#6WDQGDUG#(YHQW#UHJLVWHU#+*ESR?#FRPPDQG,#ZLOO#FOHDU#RQO\#ELW#
8#LQ#WKH#6WDWXV#%\WH#VXPPDU\#UHJLVWHU1
)RU#H[DPSOH/#57#+;#.#49,#LV#UHWXUQHG#ZKHQ#\RX#KDYH#TXHULHG#WKH#VWDWXV#RI#WKH#
6WDWXV#%\WH#UHJLVWHU/#48(6#DQG#0$9#FRQGLWLRQV#KDYH#RFFXUUHG1
The Status Byte Enable register (Request Service) is cleared when:
‡ <RX#H[HFXWH#WKH#*SRE 0#FRPPDQG1
‡ <RX#WXUQ#RQ#WKH#SRZHU#DQG#KDYH#SUHYLRXVO\#FRQILJXUHG#WKH#SRZHU#VXSSO\#
XVLQJ#WKH#*PSC 1#FRPPDQG1
‡ 7KH#HQDEOH#UHJLVWHU#ZLOO#QRW#EH#FOHDUHG#DW#SRZHU0RQ#LI#\RX#KDYH#SUHYLRXVO\#
FRQILJXUHG#WKH#SRZHU#VXSSO\#XVLQJ#*PSC 01

Using Service Request (SRQ) and Serial POLL

<RX#PXVW#FRQILJXUH#\RXU#EXV#FRQWUROOHU#WR#UHVSRQG#WR#WKH#,(((07;;#VHUYLFH#
UHTXHVW#+654,#LQWHUUXSW#WR#XVH#WKLV#FDSDELOLW\1#8VH#WKH#6WDWXV#%\WH#HQDEOH#
UHJLVWHU#+*SRE#FRPPDQG,#WR#VHOHFW#ZKLFK#VXPPDU\#ELWV#ZLOO#VHW#WKH#ORZ0OHYHO#
,(((07;;#VHUYLFH#UHTXHVW#VLJQDO1#:KHQ#ELW#9#+UHTXHVW#VHUYLFH,#LV#VHW#LQ#WKH#6WDWXV#
%\WH/#DQ#,(((07;;#VHUYLFH#UHTXHVW#LQWHUUXSW#PHVVDJH#LV#DXWRPDWLFDOO\#VHQW#WR#
WKH#EXV#FRQWUROOHU1#7KH#EXV#FRQWUROOHU#PD\#WKHQ#SROO#WKH#LQVWUXPHQWV#RQ#WKH#EXV#
WR#LGHQWLI\#ZKLFK#RQH#UHTXHVWHG#VHUYLFH#+WKH#LQVWUXPHQW#ZLWK#ELW#9#VHW#LQ#LWV#
6WDWXV#%\WH,1#
7KH#UHTXHVW#VHUYLFH#ELW#LV#FOHDUHG#RQO\#E\#UHDGLQJ#WKH#6WDWXV#%\WH#XVLQJ#DQ#
,(((07;;#VHULDO#SROO#RU#E\#UHDGLQJ#WKH#HYHQW#UHJLVWHU#ZKRVH#VXPPDU\#ELW#LV#
FDXVLQJ#WKH#VHUYLFH#UHTXHVW1
7R#UHDG#WKH#6WDWXV#%\WH#VXPPDU\#UHJLVWHU/#VHQG#WKH#,(((07;;#VHULDO#SROO#
PHVVDJH1#4XHU\LQJ#WKH#VXPPDU\#UHJLVWHU#ZLOO#UHWXUQ#D#GHFLPDO#YDOXH#ZKLFK#
FRUUHVSRQGV#WR#WKH#ELQDU\0ZHLJKWHG#VXP#RI#WKH#ELWV#VHW#LQ#WKH#UHJLVWHU1#6HULDO#
SROO#ZLOO#DXWRPDWLFDOO\#FOHDU#WKH#§UHTXHVW#VHUYLFH¨#ELW#LQ#WKH#6WDWXV#%\WH#
VXPPDU\#UHJLVWHU1#1R#RWKHU#ELWV#DUH#DIIHFWHG1#3HUIRUPLQJ#D#VHULDO#SROO#ZLOO#QRW#
DIIHFW#LQVWUXPHQW#WKURXJKSXW1
C a u t i o n
The IEEE-488 standard does not ensure synchronization between your bus controller
program and the instrument. Use the *OPC? command to guarantee that commands
previously sent to the instrument have completed. Executing a serial poll before a
*RST, *CLS, or other commands have completed can cause previous conditions
to be reported.
4
107