BALANCED HIGH PRESSURE SYSTEMS Page 7 COMBINATION BOILER SYSTEMS Page 7 In the event of any product problems, please contact the Aqualisa customer helpline on 01959 560010 for assistance. TYPICAL WATER SYSTEMS Page 8 MIDAS COMPONENTS Page 11...
12 months. diagram on page 8 ref point A or B. In the event of any difficulties please contact the Aqualisa customer helpline for assistance. Rising pipe work must not be connected into the horizontal draw-off from...
Siting Stored water capacities For optimum performance, with gravity fed systems, the distance between The minimum capacity of the cold storage cistern should not be less than the bottom of the storage cistern and the shower head should not be less 225 litres (50 gallons).
Page 5
TYPICAL GRAVITY SYSTEM INSTALLATION TYPICAL COMBINATION BOILER SYSTEM INSTALLATION (suitable for use with Midas 110/220 shower valves) (suitable for use with all Midas valves) Head to be 1m minimum Refer to page 6 (siting) TYPICAL UHW SYSTEM INSTALLATION TYPICAL GRAVITY BOOSTED SYSTEM INSTALLATION...
TYPICAL THERMAL STORAGE UNIT SYSTEM INSTALLATION MIDAS COMPONENTS (suitable for use with all Midas valves) Midas 110 shower Midas 110 shower column Midas 110 bath shower mixer...
MIDAS COMPONENTS MIDAS Midas 220 shower SHOWER INSTALLATION INSTRUCTIONS In addition to the guide below it is essential that the written instructions are read and understood and that you have all the necessary components before commencing installation. Failure to install the product in accordance with these instructions may adversely affect the •...
Page 8
When using the eccentric elbows provided we recommend leaving sufficient threads from the finished wall surface, after the cover plates have been fitted, to ensure adequate purchase for Place the cover plates onto the exposed ¾” threads, flush with the the exposed valve.
Page 9
correct position on the recess of the spigot section on the mounting plate, place nting plate in the 5 o’clock position and rotate clockwise until a stop is ng care not to over tighten MIDAS Carefully slide the gel hook onto the rail under the handset holder. Carefully slide the gel hook onto the rail under the handset holder.
Page 10
Midas 110 shower head attachment anti-swivel locking button on the handset whilst securing the n place the handset into the handset holder.
Page 11
MIDAS If required, apply jointing tape to the threads and fit the eccentric elbow connectors sufficiently to achieve a water tight seal, SHOWER COLUMN terminating at 150mm centres to suit the exposed valve inlets. INSTALLATION INSTRUCTIONS In addition to the guide below it is essential that the written instructions are read and understood and that you have all the necessary components before commencing installation.
Page 12
Ensuring the O-ring is in the correct position on the recess of the spigot section on the mounting plate, place the wall outlet onto the mounting plate in the 5 o’clock position and rotate clockwise until a stop is reached. Attach the wall fixing bracket to the riser rail connector.
Page 13
Unless in line filters are fitted to the supply pipe work we recommend the rubber filter washers should be used. Midas 110 shower head attachment Ensuring the hose washers are in the correct position, depress the anti-swivel locking button on the handset and secure the handset to the hose.
Page 14
15mm • concealed pipe work. Follow the Midas 110/220 adjustable height head installation on page 16 to complete the If required, fit the bar valve fixing accessory following the relevant installation instructions installation.
NECESSARY TO ADJUST THE FLOW CONTROL KNOB AND REDUCE THE FLOW TO ACHIEVE A COMFORTABLE SHOWERING AND BATHING TEMPERATURE. Follow the Midas 110/220 adjustable height head installation on page 16 to complete the 110 Shower Column & BSM On/Off/Flow/divert installation.
Turn the valve on by rotating the control knob towards the wall to operate the fixed head/bath N.B. ON THE MIDAS 110 HARMONY HEAD, WHEN filler, or away from the wall to operate the adjustable height head. Turn the valve off by rotating THE LEVER IS IN THE 3 O’CLOCK POSITION WHEN...
9. Secure the knob to the valve and refit the knob insert. SHOULD UNACCEPTABLE DAMAGE TO THE TEMPERATURE KNOB END CAP OCCUR WHEN REMOVING IT FROM THE TEMPERATURE KNOB, PLEASE CONTACT AQUALISA CUSTOMER SERVICE ON 01959 560010 TO ARRANGE A REPLACEMENT.
Page 19
Please note that calls may be recorded for training and quality purposes. Part Number 702042 The company reserves the right to alter, change or modify Revision Number the product specifications without prior warning. 01959 560042 Date Submitted 15/4/ 2016 ® Registered Trademark Aqualisa Products Limited. Artwork John Lavington Signoff Nicolo Agazzi...
Need help?
Do you have a question about the MIDAS 110 and is the answer not in the manual?
Questions and answers