Dynalite DMC2 Installation Instructions Manual

Modular controller

Advertisement

DMC2
DMC2-UL, DMC2-CE
Modular Controller
Devices must be installed by a
qualified electrician in accordance with
all national and local electrical and
construction codes and regulations.
Les appareils doivent être installés par un
électricien diplômé conformément à tous les
codes et réglementations électriques et de
construction nationaux et locaux.
Die Geräte sind von einem qualifizierten Elektriker
in Übereinstimmung mit allen geltenden
Vorschriften zu installieren.
1
Los dispositivos deben ser instalados por un
electricista calificado y cumpliendo todas las
normas y regulaciones, tanto nacionales como
locales, sobre instalaciones eléctricas y obras.
I dispositivi devono essere installati da un
elettricista qualificato in conformità con le norme
locali e nazionali vigenti in materia di costruzioni
edilizie e installazione di impianti elettrici.
De apparaten moeten worden aangebracht
door een gekwalificeerde elektricien en in
overeenstemming met alle nationale en
plaatselijke elektriciteits- en bouwvoorschriften.
X 4
Modules
2
IEC Pollution Degree II
40° C (104° F)
0° C (32° F)
Installation Instructions
Instructions d'installation
Installationsanweisungen
Instrucciones de instalación
Istruzioni per l'installazione
Installatie-instructies
インストール手順
安装指示
装置を取り付ける際は、 資格のある電気技師に依頼し、
国および地域の電気および建設に関するすべての法令に
従ってください。
根据国家/地区及当地的电气与建筑规范和法规,该设
备必须由有资质的电工进行安装。
380 mm (14.96 in)
285 mm (11.22 in)
352 mm (13.86 in)
≤90%
www.lighting.philips.com/dynalite
.
106 mm
(4.17 in)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DMC2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Dynalite DMC2

  • Page 1 Installation Instructions Instructions d’installation Installationsanweisungen Instrucciones de instalación Istruzioni per l’installazione Installatie-instructies インストール手順 DMC2 DMC2-UL, DMC2-CE 安装指示 Modular Controller 装置を取り付ける際は、 資格のある電気技師に依頼し、 Devices must be installed by a Los dispositivos deben ser instalados por un 国および地域の電気および建設に関するすべての法令に electricista calificado y cumpliendo todas las qualified electrician in accordance with 従ってください。...
  • Page 2 Supply Module +24 V Output Module 1 Output Module 2 Communications Module IEC Overvoltage Category III...
  • Page 3 1 Nm 8.8 Lb-in DCM-DyNet DCM-DyNet...
  • Page 4 DSM2 1 Nm 8.8 Lb-in DSM2-XX 1 Nm 8.8 Lb-in Installation example MODULE Exemple d'installation Installationsbeispiel Ejemplo de instalación Esempio di installazione Installatievoorbeeld 設置例` 安装示例...
  • Page 5 Refer to enclosure label for earth bar wire gauge and Refer to enclosure label for earth bar wire gauge and torque ratings torque ratings DSM2 DMC2 DMC4 DCM-DyNet DyNet RS-485 Device must be de-energized before terminating cables. Do not energize without the front lid top cover in place.
  • Page 6 Philips and the Philips www.lighting.philips.com/dynalite Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other trademarks are owned by Signify Holding or their respective owners.

Table of Contents