Table of Contents
Advertisement
C L E A N I N G A N D C A R E
Disconnect the power cord before cleaning or leave
the door open to inactivate the oven during cleaning.
Before cleaning ensure that the oven cavity is cool.
DO NOT USE any abrasive or harsh cleaners or
metal scouring pads that will damage or dull the
stainless steel.
Exterior
The outside surface may be cleaned with mild soap
and water; wipe with a soft cloth. Do not use any type
of household or abrasive cleaner that will damage or
dull the stainless steel.
Door
Wipe the window on both sides with a damp cloth to
remove any spills or spatters. Metal parts will be easier
to maintain if wiped frequently with a damp cloth. Avoid
the use of spray and other harsh cleaners as they may
stain, streak or dull the door surface.
Touch Control Panel
Wipe the panel with a cloth dampened slightly with
water only. Dry with a soft cloth. Do not scrub or use
any sort of chemical cleaners. Close door and touch
STOP/CLEAR.
Interior
For easy cleaning, wipe any spatters or spills with a
soft damp cloth or sponge immediately after use or at
the end of each day. The oven is easier to clean
immediately after use.
For light spills, heat 2 cups of water in a 4-cup measure
in a microwave-safe container for 15 minutes at 100%
microwave power. BE CAREFUL NOT TO BE
BURNED. Then use mild soap and wipe several times
with a soft damp cloth until all residue is removed,
being careful that none of the water or cleaner gets
into any of openings in the walls or the ceiling of the
cavity.
Do not use any abrasive, harsh or corrosive chemical
cleaners. For heavy spills, use only cleaners
recommended for stainless steel. Always put the
cleaner on a soft cloth and rub on the soiled surface,
being careful that none of the cleaner gets into any of
openings in the walls or the ceiling of the cavity. Wipe
clean with damp soft cloth. Polish dry.
Built-up splashes may overheat and begin to smoke
or catch fire and cause arcing. Harder to remove
spatters may occur if oven is not thoroughly cleaned
or if there is long time/high temperature cooking.
After cleaning the interior thoroughly, residual grease
may be removed from the interior ducts and heaters
by simply operating the oven with Refresh Cycle on
page 26. Ventilate the room if necessary.
Caution:
Make sure that mild soap or water does not seep
through the small vents in the walls, because it may
cause damage to the oven. Never spray directly onto
the oven walls. Spray onto a soft cloth and wipe.
Waveguide Cover
The waveguide cover is made from mica so requires
special care. Keep the waveguide cover clean to as-
sure good oven performance. Carefully wipe with a
damp cloth any food spatters from the surface of the
cover immediately after they occur. Built-up splashes
may overheat and cause smoke or possibly catch fire.
Accessories
The turntable, turntable support and racks can be re-
moved for easy cleaning. Wash them in mild, sudsy
water; for stubborn stains use a mild cleanser and a
non-abrasive scouring sponge. They are also dish-
washer-proof. Use upper rack of dishwasher for turn-
table support.
Foods with high acidity, such as tomatoes or lemons,
may cause the porcelain enamel turntable to discolor.
Do not cook highly acidic foods directly on the turn-
table; if spills occur, wipe up immediately.
SPECIAL NOTE for TURNTABLE
SUPPORT
After cooking, always clean the turntable support, es-
pecially around the rollers. They must be food and
grease free. Built-up food or grease may overheat and
cause arcing, begin to smoke or catch fire.
Crumb tray
Wipe the crumb tray with a soft damp cloth after use
or at the end of each day.
SERVICE MAINTENANCE CLEANING
(not covered under warranty)
It is recommended to schedule maintenance cleaning
for Exhaust Duct, Convection Fan Unit, Top Heater
Unit and Side Heater Unit by authorized servicer ev-
ery 12 months or more often if heavy grease laden
foods are cooked very frequently. Contact your near-
est SHARP AUTHORIZED SERVICER.
Oven Light Replacement
1. To replace the light bulb, first disconnnect power
cord.
2. To release cover remove the screw on the oven
light access cover. (See OVEN PARTS on page 9.)
3. Replace light bulb with a new one, 240V, 25 W bulb.
4. Replace the oven light access cover and secure
with the screw removed in step 2.
29
roller
Crumb tray
Advertisement
Table of Contents
