Installation Instructions Original Instructions Battery Replacement Catalog Number 2711P-RY2032 Topic Page Summary of Changes Important User Information Precautions About This Publication Replace Battery in PanelView Plus Terminals Replace Battery in PanelView Component Terminals Replace Battery in PanelView Plus 6 and PanelView Plus 6 Compact Terminals...
Battery Replacement Important User Information Read this document and the documents listed in the additional resources section about installation, configuration, and operation of this equipment before you install, configure, operate, or maintain this product. Users are required to familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.
Battery Replacement Precautions These products contain a sealed lithium battery which may need to be replaced during the life of the product. At the end of its life, the battery contained in this product should be collected separately from any unsorted municipal waste.
• 2713P PanelView 5310 terminals • 2711R PanelView 800 terminals IMPORTANT Use only replacement battery catalog number 2711P-RY2032, or an equivalent CR2032 lithium coin cell battery, in these products. Replace Battery in PanelView Plus Terminals Follow these steps to replace the battery in the logic module of any PanelView Plus terminal with a 700 to 1500 display.
Battery Replacement 5. Locate the battery on the circuit board. 6. Remove the battery by lifting the side of the battery. 7. Insert the new battery with the positive polarity (+) facing up. IMPORTANT The battery can be removed for up to 15 seconds without losing the clock and calendar data. 8.
Battery Replacement 3. Remove the battery. 4. Insert the new battery with the positive polarity (+) facing up. C600 /C1000 C400 Battery Battery Cover Replace Battery in PanelView Plus 6 and PanelView Plus 6 Compact Terminals 400 and 600 Terminals You can replace the battery with the terminal mounted in the panel.
Battery Replacement 4. Remove the battery. 5. Insert the new battery with the positive (+) polarity facing up and press gently until the battery snaps into place. 6. Close the battery cover and push the end in until you hear a click. Replace Battery in PanelView Plus 6 Compact Terminals 1000 Terminals Follow these steps to replace the battery in a 1000 terminal.
Page 8
Battery Replacement 4. Loosen the four captive screws that attach the logic module to the display. Communication Module Screw Logic Module Captive Screw Display Module 5. Carefully lift the logic module away from the terminal and turn over to expose the circuit board.
Battery Replacement Replace Battery in PanelView Plus 7 Standard Terminals Follow these steps to replace the battery in PanelView Plus 7 Standard terminals. 1. Disconnect power from the terminal. 2. Remove the battery cover by rotating it from the C(lose) to O(pen) position. 3.
Battery Replacement Replace Battery in PanelView Plus 7 Performance Terminals, PanelView 5500 Terminals, PanelView 5510 Terminals, and PanelView 5310 Terminals IMPORTANT Although the components of the PanelView Plus 7 Performance terminals, PanelView 5500 terminals, PanelView 5510 terminals, and PanelView 5310 terminals may differ slightly, the procedure for replacing the battery is the same for all four products.
Battery Replacement 5. Remove the battery by lifting the side of the battery. 6. Insert the new battery with the positive (+) polarity facing up. 7. Reattach the logic module by aligning the connector on the bottom of the logic module with the connector on the back of the display module.
Page 12
Battery Replacement 3. Lift the battery from the battery compartment. If necessary, use a small, flat object, such as a flat-tip screw driver, to lift the battery from the compartment. 4. Insert the new battery with the positive polarity (+) facing up. 5.
You can view or download publications at http://www.rockwellautomation.com/literature/. To order paper copies of technical documentation, contact your local Allen-Bradley® distributor or Rockwell Automation sales representative. Rockwell Automation Publication 2711P-IN009J-EN-P - December 2017...
Page 14
Rockwell Automation maintains current product environmental information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page. Allen-Bradley, FactoryTalk, PanelView, Rockwell Automation, and Rockwell Software are trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies. Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400...