Lumenier LUX-F7 Basic Manual

Lumenier LUX-F7 Basic Manual

Flight controller

Advertisement

FLIGHT CONTROLLER LUX-F7
BASIC MANUAL
MCU: 216MHz STM32F722RET6
IMU: MPU6000 & ICM20602, Dual Gyros built-in
Baro: BMP280
OSD: AT7456E
Blackbox: MicroSD card slot
5x Uarts (1,2,3,4,6) with built-in inversion
1x Softserial supported
8x Dshot/Proshot/oneshot outputs
1x I2C
1x SH1.0_8pin connector (Vbat/G/Curr/R6/S1/S2/S3/S4)
Vbat filtered output power for VTX, switchable via AUX (modes tab-user1)
Dual Camera image switchable via AUX (modes tab-user2)
Camera control
Smartaudio & Tramp VTX protocol
WS2812 Led Strip
Beeper
RSSI
INAV analog airspeed
Input: 6~36V (2~8S LiPo)
BEC: 5V 2A cont. (Max.3A)
LDO 3.3V: Max.200mA
Current Sensor: No
Battery Voltage Sensor: 1:10
Dec.2018 Rev 1.0
www.getfpv.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LUX-F7 and is the answer not in the manual?

Questions and answers

Summary of Contents for Lumenier LUX-F7

  • Page 1 FLIGHT CONTROLLER LUX-F7 BASIC MANUAL MCU: 216MHz STM32F722RET6 IMU: MPU6000 & ICM20602, Dual Gyros built-in Baro: BMP280 OSD: AT7456E Blackbox: MicroSD card slot 5x Uarts (1,2,3,4,6) with built-in inversion 1x Softserial supported 8x Dshot/Proshot/oneshot outputs 1x I2C 1x SH1.0_8pin connector (Vbat/G/Curr/R6/S1/S2/S3/S4)
  • Page 2 No function in BF Size & Weight: 36x36mm /7g Holes: Φ4mm, 30.5mm mounting 6000 Packing 1x LUX-F7 1x SH1.0_8pin to 8pin cable 1x SH1.0_6pin connector 6x M3 Silicon Grommets Vbat: Battery voltage filtered, Max.1A load on this pad. (Default ON)
  • Page 3 Target BetaFlight / INAV: MATEKF722SE *** CLI defaults after reflashing Check and swap the Gyros (BetaFlight) status get gyro_to_use FIRST = MPU6000 by default SECOND = ICM20602 BOTH is not supported on this FC Select ICM20602 set gyro_to_use = second save *** ICM20602 provides fast response, but it is sensitive.
  • Page 4 Wiring 4in1 ESC w/ one current sensor Use the current sensor scale of 4in1 4in1 ESC BLHELI32 w/ individual current sensor SBUS CRSF SBUS SmartPort PPM/IBUS FPORT FPORT PPM/IBUS *** BF CLI resource serial_tx 11 A02 to get softserial_tx1 on T2 pad for SmartPort SBUS/IBUS/DSM can be connected to any unused UART_RX FPort, SmartPort can be connected to any unused UART_TX *** PPM share R2 pad, must disable Serial RX on UART2...
  • Page 5 Wiring (INAV Airplane) SBUS CRSF SBUS SmartPort PPM/IBUS FPORT FPORT PPM/IBUS STM32F722RET6 *** Enable softserial_tx1 on T2 pad for saving one Uart SBUS/IBUS/DSM can be connected to any unused UART_RX FPort, SmartPort can be connected to any unused UART_TX *** PPM share R2 pad, must disable Serial RX on UART2 Battery Battery Battery...

Table of Contents