Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Techome TVL3
Summary of Contents for Techome TVL3
- Page 1 VERSION 2 USER MANUAL TV Lifting System...
-
Page 2: Table Of Contents
Contents 1. Overview 2. System Introduction Package Contents Appearance Specification 2.3.1 2D drawing of the TVL3 lifting column Installation guide Getting started 2.5.1 Concealed Switch Box : Setting the desired maximum height 2.5.2 IR Control: Setting the lift height 2.5.3 RF Control-TH3: Setting the lift height 2.5.4... -
Page 3: Overview
TecHome TVL3 series columns are primarily designed for use as TV lifts, but can be used in other applications that require vertical movement using a remote control. Our steel constructed TVL3 is available in three sizes depending on the requirements of the application. An extended height position can be programmed using our remote control. -
Page 4: System Introduction
TV Lift System User Manual 2.System Introduction 2.1 Package Contents Chart A: List of the package content Description Model Name Q’ty Lift Column TVL3 Control Box TC11 1 pc Control 1 pc Control IR Control 1 pc Accessory TJB2 1 pc... -
Page 5: Appearance
TV Lift System User Manual 2.2 Appearance Version 2．October 2015 4 of 16... -
Page 6: Specification
TV Lift System User Manual 2.3 Specifications 2.3.1 2D drawing of the TVL3 lifting column TVL3 Specifications Size Retracted Stroke Fixing Hole Max. Load Speed (mm/sec) Recommended Length (mm) Distance TV Size (inch) (mm) (mm) (Note) Large 35 mm/s at 50”~70”... - Page 7 RF wireless control available Control: IR Control 10.3 Used to set the maximum height of the TVL3 Works with the IR receiver to control the TVL3 height Accessories: TJB2 Junction box Embedded with RF receiver ...
- Page 8 TV Lift System User Manual Accessories: IR Receiver Required for IR control Accessories: Conceal Switch Box Used as a back-up control if 31.8 50.0 the primary control runs out of battery Includes SET button for advanced settings (Note) Note: When this is switched to the “SET”...
- Page 9 TV Lift System User Manual Component Package List Description Drawing Q’ty (pcs) Wheel (Ø18* Ø8*20L) Shaft (Ø8* Ø8*28L) Shaft Holder Shaft Holder Screw (M5*8L) Manual Screw (M5*10L) Washer (M8) Slider (40*14*3t) Screw (M8*15L) Handle Screw (M6*24L) Version 2．October 2015 of 16...
-
Page 10: Installation Guide
Install the TV, using the newly installed brackets, to the TVL3. Screw tight on the top of the brackets. Slowly release the TV to make sure it is installed securely. Plug in the TVL3 and raise it the full height so that it’s fully extended. - Page 11 TV Lift System User Manual Version 2．October 2015 10 of 16...
-
Page 12: Getting Started
TV Lift System User Manual 2.5 Getting started 2.5.1 Concealed Switch Box : Setting the desired maximum height How to set the desired lift height Press and hold the up or down button to the desired height, release the button, and then switch SET to the “ON”... - Page 13 DOWN, and then switch SET to “ON”. Press and hold the “DOWN” button for 3 seconds until the TC11 beeps once. Switch SET to “OFF” to complete the process. Note: This is primarily used when the TVL3 is installed within a TV cabinet. Version 2．October 2015 12 of 16...
-
Page 14: Ir Control: Setting The Lift Height
Once the desired height has been reached, press and hold the “M” button until the TC11 beeps 3 times. This confirms the desired height is saved to memory. Click “M” and the TVL3 will automatically travel to the memorized height. How to disable the memorized height Press and hold the “M”... -
Page 15: Rf Control-Th3: Setting The Lift Height
How to set the desired maximum height limit? Press and hold the “ ” button on the RF Control-TH3, The TVL3 will travel upwards. Once the desired maximum height has been reached, press and hold the “M” and “... - Page 16 Once the desired height has been reached, press and hold the “M” button until the TC11 beeps 3 times. This confirms the memorized height is now saved to memory. Click “M” and the TVL3 will automatically travel to the memorized height. How to disable the memorized height To disable the memorized height, press and hold the “M”...
-
Page 17: Operation
TV Lift System User Manual 2.5.4 Operation Once the memorized height of the TVL3 column is set, users can use either the control-TH3 or IR Control to control movement of the lifting system. (1) Press and hold the symbol to move the column upwards.
Need help?
Do you have a question about the TVL3 and is the answer not in the manual?
Questions and answers