Niigata seiki ALD Series Instruction Manual

S-LINE SNAP GAUGE
Precision
Measuring
Tool
Thank you for purchasing the S-Line Snap Gauge. Mount a digital micrometer or indicator to this precision gauge holder for precise hand
held measurements of part dimensions.
● For safe and proper use of this product, please read this instruction manual
before use and follow the procedures described. Please keep manual where
it is accessible to user for future reference.
● Keep this manual with the instrument if transferred or leased to a third party.
● For inquiries about this product, please contact dealer or Niigata Seiki at
the address listed on the following page.
■ PART IDENTIFICATION, FUNCTION
※Model ALD-080 shown
⑤ Gauge mounting Hole
⑥ Gauge Clamp Screw
(rear)
⑦ Measurement
Lever
⑨ Work Stop Clamp Screw (rear)
① Spindle ······························· Movement displayed on Gauge.
② Anvil ··································· Workpiece is held between this
③ Anvil Feed Screw ··············· For adjusting Spindle position.
④ Anvil Lock Screw (rear) ······ Fixes Anvil position.
⑤ Gauge Mounting Hole ········ Mount your Gauge here

SAFETY PRECAUTIONS

Always follow the procedures specified in order to prevent harm
to yourself or others, and to prevent damage to property.
Denotes a prohibition
– You MUST NOT do
Items where there is potential of injury or
CAUTION
property damage.
Read the manual and follow all instructions.
・Use of product other than as described in the manual
may cause accident.
Use only for measuring.
・Use for any purpose other than measuring may cause
damage or wear to the instrument. Improper use may
also cause accident.
Handle with Care.
・Do not drop or subject instrument to excessive shock.
Do not place under heavy objects. Improper handling
may cause damage or poor accuracy.
・Do not scratch instrument.
Press on Lever Gently
・Rough handling may cause damage or affect accuracy.
PROFESSIONAL
① Spindle
⑩ Stand Mounting
Hole
and the Spindle.
(8mm Stem).
Please
Denotes a requirement
– You MUST do
In this manual,
OR PROPERTY DAMAGE if not followed. The
indicates something which is PROHIBITED, and the
symbol indicates REQUIRED step or necessary condition.
② Anvil
⑥ Gauge Clamp Screw (rear) ······ Tighten to secure Gauge.
⑦ Measurement Lever ················· Press Lever to move Spindle.
⑧ Work Stop ······························· Guide for positioning cylindrical
⑨ Work Stop Clamp Screw (rear) ··· Fixes Stop position.
⑩ Stand Mounting Hole ················ Mounting hole for attaching to
Use and store only in the following conditions:
Observe
● Dry location protected from rain, water, and oils.
● Protected from direct sunlight.
● Location that does not become hot.
● Location protected from use by children and
・Use in conditions other than indicated above may
Do not disassemble or modify.
・Doing so may cause accident or injury. Please contact
After use, treat with rust preventive and store in dry
location protected from direct sunlight.
・Spindle and Anvil require rust preventive after use to
WORKPIECE
Make sure the part being measured is appropriate.
Use on parts which are not rigid may cause deformation during
measurement or damage to workpiece.
Material must not be easily deformed.
※Depending on size and thickness, soft material such as aluminum or
plastic may deform and measurement will be in error.
Instruction Manual
Model No.
SAFETY NOTIFICATIONS
indicates RISK OF PERSONAL INJURY
③ Anvil Feed Screw
④ Anvil Lock Screw (rear)
⑧ Work Stop
workpieces for measurement.
Stand.
unauthorized people.
result in poor accuracy, damage to product, or cause
accidents or injury.
distributor or place of purchase for service.
insure smooth operation.
ALD-＊ ＊ ＊
symbol