English
Unknown
- Menus and Screens
  - Screen Icons and Features
  - Remote (VNC) Connection
  - Main Menu
  - Multi-Receiver Menu
- Multi -Receiver Menu
  - Multi-Receiver Settings Menu
  - Own Aircraft Menu
  - Receiver Menu
  - Filtered Masked Menu
  - Predefined Masks Menu
  - Customize Mode S Mask Menu
  - Highlight Masked Menu
    
    RTCA/DO-260 Tests
    
    Scenario Menu
  - Transponder Menu
    
    Transponder Settings Menu
    
    Transponder Measurements Menu
    
    Transponder Receiver Menu
  - Filtered Masked Menu
  - Predefined Masks Menu
  - Customize Mode S Mask Menu
  - Highlight Masked Menu
    
    Transponder Test Menu - Single Interrogation
    
    Transponder Test Menu - Double Interrogation
    
    Transponder Test Menu - Interrogation Table
    
    Transponder Test Menu - Block Transmission
    
    Transponder Test Menu - Interrogation with CW
  - DME Menu
    
    DME Settings Menu
    
    DME Measurements Menu
    
    DME Test Menu
    
    UAT Menu
    
    UAT Settings Menu
    
    UAT Receiving Station Menu
    
    UAT Receiver Menu
  - Filtered Masked Menu
  - Predefined Masks Menu
  - Customize Mode S Mask Menu
  - Highlight Masked Menu
    
    UAT Scenario Menu - Normal Mode
  - System Menu
    
    Software Update Menu
    
    Network Connections Menu
    
    Configuration Menu
    
    Calibration Menu
  - Support Menu
- Operating Procedures and Test Configurations
  - Operating Procedrues
    
    How to Change the GPIB Address
    
    How to Change the Transmitter Frequency
    
    How to Set a Scope Output
    
    How to Program the DSP Software or FPGA Firmware
    
    How to Enter the Own Aircraft Information
  - Test Configurations
    
    Transponder Atc/Mode S/ELS/EHS Test Configuration
    
    Transponder ADS-B out (1090ES) Test Configuration
- Remote Operation
  - Overview
  - Measurement Commands
    
    Data Format
    
    Df Data Frame Bit
    
    Mode
    
    Pulse
    
    Pulse Request
    
    Spr
    
    Trigger Parameters
  - Own Aircraft Commands
    
    Altitude
    
    Heading
    
    Latitude
    
    Longitude
    
    Mode S Address
  - Receiver Commands
    
    Log Parameters
    
    Mask
    
    Status Request
    
    Utc Time
  - Rtca/Do-260 Test Commands
    
    Generator Parameters
    
    Load
    
    Number of Transmissions
    
    Reset
    
    Save
    
    Special Test
    
    Start
    
    Stop
    
    Test Status Request
    
    Trigger Parameters
    
    Block Transmission
  - Scenario Commands
    
    Individual 1030 Messages
    
    Intruders Definition Parameters
    
    Scenario Parameters
    
    Uat Ads-B Definition Parameters
    
    Uat Ground Uplink Definition Parameters
  - Settings Commands
    
    Factory Settings
    
    Scope Port
    
    Tx Generator Parameters
  - Transponder Commands
    
    Cable Loss
    
    Cable Loss Bottom
    
    Interference Pulse
    
    Interrogation Frequency
    
    Interrogation On/Off
    
    Interrogation Test Type
    
    Interrogation Top Antenna Power
    
    Load Test
    
    Reset
    
    Save Test
    
    Scope Trigger
    
    Scope Trigger Offset
    
    Start Transmission
    
    Stop Transmission
    
    Suppression Output
    
    Suppression Percentage
    
    Transmission Modes
  - Unit Commands
    
    Hardware Version Request
    
    Last Calibration Date Request
    
    Mode of Operation
    
    Part Number Request
    
    Product Key Request
    
    Reset
    
    Serial Number Request
    
    Software Version Request
    
    Unit Name Request
    
    Versions Request
  - Dme Commands
    
    Acceleration
    
    Cable Loss
    
    Channel
    
    Channel Mode
    
    Direction
    
    Echo
    
    Echo Power
    
    Efficiency
    
    Ident Character
    
    Ident Code
    
    Ident Dash
    
    Ident Dot
    
    Ident Mode
    
    Ident Rate
    
    Ident Space
    
    Load Test
    
    P2 Position
    
    Power
    
    Prf
    
    Pulse
    
    Range
    
    Range Mode
    
    Reset
    
    Save Test
    
    Squitter
    
    Start
    
    Stop
    
    Suppression
    
    Suppression Percentage
    
    Velocity
    
    Width
    
    Equalizer
    
    Trigger
    
    Self Interrogation
  - Examples
    
    Scenario Test
    
    Test Single ADS-B Example
    
    Test Dual ADS-B Example
    
    Special Test Overlapping Pulse Example
    
    Special Test Bit Failures Example
    
    Special Test Altered Preamble Example
    
    Transponder Block Transmission Example
    
    UAT Scenario Definition Example
    
    Example Program
- Section 3 - Specifications
  - Transmitter
    
    Frequency
    
    Power
    
    Spectral Purity (Typical)
    
    Channels
    
    Diversity
    
    Modulation
    
    Pulse Position
    
    Pulse Width
    
    Pulse Rise/Fall Time
    
    Pulse Amplitude
    
    Interrogation Table/Burst Mode
    
    Block Transmissions
    
    Prf
    
    Interlace Ratio
    
    Suppressor Pulse
    
    DME Simulation
    
    Receiver
    
    Vswr
    
    Maximum Input Power
    
    Receiver Decoding Messages
    
    Operating Range
    
    Channels
    
    Measurement
    
    Scope Trigger Output (Scope 1 and Scope 2)
    
    Environmental
    
    Full Specified Performance
    
    Operating
    
    Storage
    
    Relative Humidity
    
    Degree of Protection
    
    Physical
    
    AC Input Power
    
    Voltage Range
    
    Compliance/Standards
    
    Directives
    
    EMC Compliance
    
    Safety Standards
- Section 4 - Shipping
  - Shipping Test Sets
    
    Information
    
    Authorization
    
    Tagging Test Sets
    
    Shipping Containers
    
    Freight Costs
    
    Repacking Procedure
- Section 5 - Storage
  - Storing Test Set
- Appendix A - Connector Pin-Out Tables
  - I/O Connectors - Front Panel
  - I/O Connectors - Rear Panel
  - Ate Line Connector Pin-Out Table
  - Gpib Bus Connector Pin-Out Table
  - Lan Connector Pin-Out Table
  - Usb (A) Connector Pin-Out Table
  - Usb (B) Connector Pin-Out Table
- Appendix B - Metric/British Imperial Conversion Table with Nautical Distance Conversions
- Appendix C - Abbreviations
- Appendix D - Atc-5000Ng Compatibility Command Set
  - SDX Compatibility Command Set
  - ATC-1400A/S-1403D Compatibility Command Set
    
    ATC-1400A Compatibility Command Set
    
    1403DL Compatibility Command Set
    
    Axn Commands S-1403DL
    
    S-1403DL Compatibility Command Set

Quick Links

Download this manual

ATC/DME Test Set

ATC-5000NG

Operation Manual

Issue-10

EXPORT CONTROL WARNING: This document contains controlled technical data under the

jurisdiction of the Export Administration Regulations (EAR), 15 CFR 730-774. It cannot be

transferred to any foreign third party without the specific prior approval of the U.S. Department of

Commerce, Bureau of Industry and Security (BIS). Violations of these regulations are punishable

by fine, imprisonment, or both.

Table of Contents

Chapters

Table of Contents

Need help?

Do you have a question about the ATC-5000NG and is the answer not in the manual?

Questions and answers

Summary of Contents for Aeroflex ATC-5000NG

Page 1 ATC/DME Test Set ATC-5000NG Operation Manual Issue-10 EXPORT CONTROL WARNING: This document contains controlled technical data under the jurisdiction of the Export Administration Regulations (EAR), 15 CFR 730-774. It cannot be transferred to any foreign third party without the specific prior approval of the U.S. Department of Commerce, Bureau of Industry and Security (BIS).
Page 2 OPERATION MANUAL ATC/DME TEST SET ATC-5000NG P U B L I S H E D B Y A e r o f l e x C O P YR I G H T  A e r o f l e x 2 0 1 8 A l l r i g h t s r e s e r v e d .
Page 3 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 4 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G E l e c t r o m a g n e t i c C o m p a t i b i l i t y : F o r c o n t i n u e d E MC c o m p l i a n c e , a l l e xt e r n a l c a b l e s m u s t b e s h i e l d e d a n d t h r e e m e t e r s o r l e s s i n l e n g t h .
Page 5 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G TH I S P A G E I N TE N TI O N A L L Y L E F T B L A N K . S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 6 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S AF E T Y F I R S T : T O AL L O P E R AT I O N S P E R S O N N E L R E F E R AL L S E R V I C I N G O F U N I T T O Q U AL I F I E D T E C H N I C AL P E R S O N N E L .
Page 7 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S AF E T Y F I R S T : T O AL L O P E R AT I O N S P E R S O N N E L ( C O N T ) C AU T I O N : S I G N A L G E N E R A T O R S C A N B E A S O U R C E O F E L E C T R O M A G N E T I C I N T E R F E R E N C E ( E M I ) T O C O M M U N I C A T I O N R E C E I V E R S .
Page 8 DECLARATION OF CONFORMITY The Declaration of Conformity Certificate included with the unit should remain with the unit. Aeroflex recommends the operator reproduce a copy of the Declaration of Conformity Certificate to be stored with the Operation Manual for future reference.
Page 9 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G TH I S P A G E I N TE N TI O N A L L Y L E F T B L A N K . S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 10 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G T AB L E O F C O N T E N T S Ti t l e C h a p t e r / S e c t i o n Ti t l e / C o p yr i g h t P a g e S t a t e m e n t s...
Page 11 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G TH I S P A G E I N TE N TI O N A L L Y L E F T B L A N K TA B L E O F C O N TE N TS P a g e 2 S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 12 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G I N T R O D U C T I O N Th i s m a n u a l c o n t a i n s o p e r a t i n g i n s t r u c t i o n s f o r t h e A TC - 5 0 0 0 N G . A e r o f l e x s t r o n g l y r e c o m m e n d s t h a t p e r s o n n e l b e t h o r o u g h l y f a m i l i a r wi t h t h e c o n t e n t s o f t h i s m a n u a l b e f o r e a t t e m p t i n g t o o p e r a t e t h e e q u i p m e n t .
Page 13 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G TH I S P A G E I N TE N TI O N A L L Y L E F T B L A N K . I N TR O D U C TI O N P a g e 2 Ma r 1 4 / 1 8...
Page 14: Table Of Contents
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G C H AP T E R O N E AT C - 5 0 0 0 N G AT C / D M E T E S T S E T O P E R AT I O N M AN U AL T AB L E O F C O N T E N T S S e c t i o n / Ti t l e...
Page 15 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S e c t i o n / Ti t l e P a g e 3.6.
Page 16 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S e c t i o n / Ti t l e P a g e 5.5.
Page 17 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S e c t i o n / Ti t l e P a g e 5.9.
Page 18 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S e c t i o n / Ti t l e P a g e 5.11.
Page 19 ONNECTOR ABLE APPENDIX B – METRIC/BRITISH IMPERIAL CONVERSION TABLE WITH NAUTICAL DISTANCE CONVERSIONS..........1 APPENDIX C – ABBREVIATIONS ................................1 APPENDIX D - ATC-5000NG COMPATIBILITY COMMAND SET ........................1 D.1. SDX Compatibility Command Set .............................. 1 D.2. ATC-1400A/S-1403D Compatibility Command Set ........................9 D.2.1.
Page 20 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G L I S T O F I L L U S T R AT I O N S F i g u r e / Ti t l e S e c t i o n / P a r a P a g e...
Page 21 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G TH I S P A G E I N TE N TI O N A L L Y L E F T B L A N K . 1 - L I S T O F I L L U S TR A TI O N S P a g e 2 S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 22 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S E R V I C E U P O N R E C E I P T O F M AT E R I AL U n p a c k i n g S p e c i a l - d e s i g n p a c k i n g m a t e r i a l i n s i d e t h e s h i p p i n g c o n t a i n e r p r o vi d e s m a xi m u m p r o t e c t i o n f o r t h e A TC - 5 0 0 0 N G .
Page 23 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G C h e c k i n g U n p a c k e d E q u i p m e n t ( c o n t ) 1 - S E R V I C E U P O N R E C E I P T P a g e 2 S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 24 D E S C R I P T I O N P AR T N U M B E R Q T Y ATC-5000NG ATC/DME Test Set 1 3 8 1 5 6 Manual, Getting Started (Paper) 1 3 9 1 8 9...
Page 25 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G C h e c k i n g U n p a c k e d E q u i p m e n t ( c o n t ) S T AN D AR D I T E M S A T C - 5 0 0 0 N G M a n u a l , G e t t i n g S t a r t e d ( P a p e r )
Page 26 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G C h e c k i n g U n p a c k e d E q u i p m e n t ( c o n t ) O P T I O N AL I T E M S D E S C R I P T I O N O P T I O N N U M B E R...
Page 27 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G TH I S P A G E I N TE N TI O N A L L Y L E F T B L A N K . 1 - S E R V I C E U P O N R E C E I P T P a g e 6 S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 28: Section 1 - Description
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G SECTION 1 – DESCRIPTION GENERAL DESCRIPTION AND CAPABILITIES 1.1. DESCRIPTION Th e A TC - 5 0 0 0 N G i s a n R F S i g n a l G e n e r a t o r / R e c e i ve r f o r t e s t i n g Mo d e A , C a n d S Tr a n s p o n d e r s . 1.2.
Page 29 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G FUNCTIONAL CAPABILITIES (CONT) • E q u i p m e n t t e s t e d : •...
Page 30: Section 2 - Operation
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G SECTION 2 – OPERATION INSTALLATION 1.1. GENERAL 1.1.1. BENCH USE R e f e r t o 1 - 2 - 2 , F i g u r e s 1 a n d 2 f o r l o c a t i o n o f c o n t r o l s , c o n n e c t o r s o r i n d i c a t o r s . S TE P P R O C E D U R E 1 .
Page 31: Grounding Power Cord
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 1.2.2. GROUNDING POWER CORD W AR N I N G : D O N O T U S E A T H R E E - P R O N G T O T W O - P R O N G AD AP T E R P L U G . D O I N G S O C R E AT E S A S H O C K H AZ AR D B E T W E E N T H E C H AS S I S AN D E L E C T R I C AL G R O U N D .
Page 32: External Cleaning
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 1.4. EXTERNAL CLEANING Th e f o l l o wi n g p r o c e d u r e c o n t a i n s r o u t i n e i n s t r u c t i o n s f o r c l e a n i n g t h e o u t s i d e o f t h e Te s t S e t . C AU T I O N : D I S C O N N E C T P O W E R F R OM T E S T S E T T O AV O I D P O S S I B L E D AM AG E T O E L E C T R O N I C C I R C U I T S .
Page 33 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G TH I S P A G E I N TE N TI O N A L L Y L E F T B L A N K . 1 - 2 - 1 P a g e 4 S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 34: Controls, Connectors And Indicators
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G CONTROLS, CONNECTORS AND INDICATORS 2.1. FRONT PANEL R e f e r t o F i g u r e 1 A TC - 5 0 0 0 N G F r o n t P a n e l f o r l o c a t i o n o f F r o n t P a n e l c o n t r o l s , c o n n e c t o r s o r i n d i c a t o r s .
Page 35: Rear Panel
Power Connector Standard 3-prong power receptacle for connection to AC power source (100 to 240 VAC, 50 to 60 Hz). Connects (I) or disconnects (O) external AC power from the ATC-5000NG. Power Switch 1 - 2 - 2 P a g e 2 S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 36: Menus And Screens
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G MENUS AND SCREENS N O T E : T H E S C R E E N I M AG E S S H O W N I N T H I S S E C T I O N AR E R E P R E S E N T AT I O N S O F T H E S C R E E N S T H AT U S E R S M AY E N C O U N T E R W H E N U S I N G T H E T E S T S E T .
Page 37 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G PARA # TITLE PAGE 3.7................................97 YSTEM 3.7.1. Software Update Menu ............................99 3.7.2. Network Connections Menu ..........................
Page 38: Screen Icons And Features
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.1. SCREEN ICONS AND FEATURES S c r e e n I c o n s a n d I n d i c a t o r s S C R E E N I C O N D E S C R I P T I O N E xt e r n a l e q u i p m e n t i s c o n n e c t e d t o t h e L A N C o n n e c t o r ( F r o n t...
Page 39 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G SCREEN ICONS AND FEATURES (CONT) S c r e e n F e a t u r e s S C R E E N F E AT U R E D E S C R I P T I O N Local Mode - All controls on the Touch Screen are enabled.
Page 40 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G SCREEN ICONS AND FEATURES (CONT) S c r e e n F e a t u r e s ( c o n t ) S C R E E N F E AT U R E D E S C R I P T I O N W h e n g r e e n , p r e s s t h e a r r o w t o d i s p l a y a d d i t i o n a l S o f t k e ys .
Page 41: Remote (Vnc) Connection
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.2. REMOTE (VNC) CONNECTION To c r e a t e a R e m o t e ( V N C ) C o n n e c t i o n t o t h e A TC- 5 0 0 0 N G , p e r f o r m t h e f o l l o wi n g s t e p s : S TE P P R O C E D U R E O p e n I n t e r n e t B r o ws e r ( I n t e r n e t E xp l o r e r , Mo zi l l a , S a f a r i , e t c .
Page 42 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G REMOTE CONNECTION (CONT) S TE P P R O C E D U R E ( C O N T) P l u g a n E t h e r n e t C a b l e i n t o t h e L A N C o n n e c t o r o n t h e F r o n t o r R e a r P a n e l o f t h e A TC- 5 0 0 0 N G .
Page 43 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.2. REMOTE CONNECTION (CONT) I P a d / S m a r t p h o n e To e s t a b l i s h a V N C R e m o t e C o n n e c t i o n f r o m a n I P a d o r S m a r t p h o n e , d o wn l o a d t h e V N C A p p i n t o t h e d e v i c e .
Page 44: Main Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.3. MAIN MENU Th e Ma i n Me n u d i s p l a y s t h e s t a t u s o f t h e Te s t S e t c o n f i g u r a t i o n s a n d s o f t wa r e ve r s i o n s . P r e s s A L T + R t o r e f r e s h t h e f i r m wa r e ve r s i o n s .
Page 45 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S C R E E N C O M P O N E N T S D E S C R I P T I O N D i s p l a y s t h e Tr a n s m i t t e r Mo d u l e # 3 F P G A V e r s i o n .
Page 46: Multi-Receiver Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.4. MULTI-RECEIVER MENU Th e Mu l t i - R e c e i v e r Me n u a l l o ws t h e u s e r t o p e r f o r m D O- 2 6 0 t e s t s a n d a l s o a l l o ws t h e u s e r t o s e t u p s c e n a r i o s t h a t o u t p u t 1 0 9 0 m e s s a g e s ( A D S- B ) , 1 0 3 0 i n t e r r o g a t i o n s ( Mo d e S a n d A TC R B S ) a n d U A T m e s s a g e s ( A i r b o r n e a n d G r o u n d l i n k ) s i m u l t a n e o u s l y o n a n a n t e n n a p o r t.
Page 47: Multi-Receiver Settings Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.4.1. MULTI-RECEIVER SETTINGS MENU Th e Mu l t i - R e c e i v e r S e t t i n g s Me n u a l l o ws t h e u s e r t o c o n f i g u r e t h e Tr a n s m i t t e r , R e c e i ve r a n d A n t e n n a S i m u l a t o r m o d u l e s wi t h i n t h e Te s t S e t f o r Mu l t i - R e c e i ve r t e s t s .
Page 48: Own Aircraft Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.4.2. OWN AIRCRAFT MENU Th e O wn A i r c r a f t Me n u a l l o ws t h e u s e r t o c h a n g e t h e l a t i t u d e , l o n g i t u d e , a l t i t u d e , h e a d i n g a n d Mo d e S a d d r e s s o f t h e O wn A i r c r a f t .
Page 49: Receiver Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.4.3. RECEIVER MENU Th e R e c e i ve r Me n u a l l o ws t h e u s e r t o v i e w t h e t r a n s m i s s i o n s f r o m t h e U U T a n d t h e Te s t S e t . Th e l a s t 8 r e c e p t i o n s a r e d i s p l a y e d .
Page 50 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.4.3 RECEIVER MENU (CONT) S C R E E N C O M P O N E N T D E S C R I P T I O N C a p t u r e S o f t k e y A c c e s s e s t h e f o l l o wi n g s o f t k e ys :...
Page 51 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.4.3 RECEIVER MENU (CONT) S C R E E N C O M P O N E N T D E S C R I P T I O N D i s p l a y S o f t K e y A l l o ws t h e u s e r t o s e l e c t t h e d i s p l a y s e t t i n g s .
Page 52 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.4.3 RECEIVER MENU (CONT) S C R E E N C O M P O N E N T D E S C R I P T I O N A c c e s s e s t h e f o l l o wi n g f u n c t i o n s : D a t a L o g g i n g S o f t k e y...
Page 53: Filtered Masked Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.4.3.1. Filtered Masked Menu A l l o ws t h e u s e r t o s e l e c t t h e m e s s a g e s t o f i l t e r a n d d i s p l a y i n t h e R e c e i ve r Me n u . S C R E E N C O M P O N E N T D E S C R I P T I O N P r e d e f i n e d M a s k s S o f t k e y...
Page 54: Predefined Masks Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.4.3.2. Predefined Masks Menu S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o s e l e c t g r o u p s o f U F a n d D F m e s s a g e s .
Page 55: Customize Mode S Mask Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.4.3.3. Customize Mode S Mask Menu S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o e n a b l e / d i s a b l e t h e s e l e c t e d p a t t e r n b i t .
Page 56: Highlight Masked Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.4.3.4. Highlight Masked Menu A l l o ws t h e u s e r t o s e l e c t t h e m e s s a g e s t o h i g h l i g h t d u r i n g t h e d i s p l a y o f m e s s a g e s i n t h e Tr a n s p o n d e r R e c e i ve r Me n u .
Page 57: Rtca/Do-260 Tests
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.4.4. RTCA/DO-260 TESTS Th e R TC A / D O - 2 6 0 Te s t s Me n u a l l o ws t h e u s e r t o d e f i n e t e s t s t h a t s e t t h e Te s t S e t Tr a n s m i t t e r s f o r R TC A D O - 2 6 0 R e c e i ve r t e s t i n g .
Page 58 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o s e l e c t t h e R a n d o m W i d t h .
Page 59 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.4.4. RTCA/DO-260 TESTS (CONT) W h e n t h e R TC A / D O - 2 6 0 S p e c i a l Te s t D e f i n i t i o n Me n u i s d i s p l a ye d , t h e u s e r c a n a l t e r t h e p a r a m e t e r s . R T C A/ D O - 2 6 0 S p e c i a l T e s t D e f i n i t i o n M e n u ( N o r m a l ) S C R E E N C O M P O N E N T S D E S C R I P T I O N...
Page 60 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.4.4. RTCA/DO-260 TESTS (CONT) R T C A/ D O - 2 6 0 T i m i n g D e f i n i t i o n M e n u ( N o r m a l ) S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o s e l e c t t h e Tr i g g e r S o u r c e .
Page 61 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.4.4. RTCA/DO-260 TESTS (CONT) R T C A/ D O - 2 6 0 G e n e r a t o r D e f i n i t i o n M e n u ( N o r m a l ) 1 - 2 - 3 P a g e 2 6 S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 62 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.4.4. RTCA/DO-260 TESTS (CONT) S C R E E N C O M P O N E N T S D E S C R I P T I O N G e n e r a t o r A l l o ws t h e u s e r t o s e l e c t t h e G e n e r a t o r .
Page 63 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S C R E E N C O M P O N E N T S D E S C R I P T I O N e xc l u d i n g t h e f i r s t f i v e b i t s a n d t h e P I f i e l d .
Page 64 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.4.4. RTCA/DO-260 TESTS (CONT) R T C A/ D O - 2 6 0 G e n e r a t o r D e f i n i t i o n M e n u - F r a m e D e t a i l s ( N o r m a l ) 1 - 2 - 3 P a g e 2 9 S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 65 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.4.4. RTCA/DO-260 TESTS (CONT) R T C A/ D O - 2 6 0 G e n e r a t o r D e f i n i t i o n M e n u - M o d e S P u l s e I n f o r m a t i o n ( N o r m a l ) S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o r e s e t a l l Mo d e S p u l s e s e t t i n g s .
Page 66 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.4.4. RTCA/DO-260 TESTS (CONT) R T C A/ D O - 2 6 0 G e n e r a t o r D e f i n i t i o n M e n u - AT C R B S P u l s e I n f o r m a t i o n ( N o r m a l ) S C R E E N C O M P O N E N T S D E S C R I P T I O N R e s e t S o f t k e y...
Page 67: Scenario Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.4.5. SCENARIO MENU Th e S c e n a r i o Me n u a l l o ws t h e u s e r t o d e f i n e t e s t s t h a t s e t t h e Te s t S e t t o t r a n s m i t 1 0 9 0 A D S- B m e s s a g e s , 1 0 3 0 I n t e r r o g a t i o n m e s s a g e s a n d U A T m e s s a g e s s i m u l t a n e o u s l y.
Page 68 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o s e l e c t t h e I n i t i a l MS O f o r U A T D yn a m i c I n i t i a l M S O D yn a m i c U AT...
Page 69 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.4.5. SCENARIO MENU (CONT) 1 0 9 0 T a r g e t s M e n u ( D yn a m i c ) S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o s e l e c t t h e Ty p e .
Page 70 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o s e l e c t t h e S q u i t t e r A n t e n n a .
Page 71 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.4.5. SCENARIO MENU (CONT) 1 0 3 0 M e s s a g e s M e n u S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o a d d a n e w 1 0 3 0 i n t e r r o g a t i o n .
Page 72 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.4.5. SCENARIO MENU (CONT) 1 0 9 0 T a r g e t S q u i t t e r D e f i n i t i o n M e n u S C R E E N C O M P O N E N T S D E S C R I P T I O N D i s p l a y s t h e S q u i t t e r F r a m e F i e l d s Me n u .
Page 73 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.4.5. SCENARIO MENU (CONT) S q u i t t e r F r a m e F i e l d s M e n u 1 - 2 - 3 P a g e 3 8 S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 74 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.4.5. SCENARIO MENU (CONT) S q u i t t e r S c h e d u l e M e n u 1 - 2 - 3 P a g e 3 9 S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 75: Transponder Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5. TRANSPONDER MENU S C R E E N C O M P O N E N T S D E S C R I P T I O N D i s p l a y s t h e Tr a n s p o n d e r S e t t i n g s Me n u .
Page 76: Transponder Settings Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5.1. TRANSPONDER SETTINGS MENU A l l o ws t h e u s e r t o c o n f i g u r e t h e Tr a n s m i t t e r , R e c e i ve r a n d A n t e n n a / S wi t c h m o d u l e s i n t h e Te s t S e t f o r t r a n s p o n d e r t e s t s .
Page 77: Transponder Measurements Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5.2. TRANSPONDER MEASUREMENTS MENU A l l o ws t h e u s e r t o v i e w t h e p u l s e s f r o m t h e Tr a n s p o n d e r o r A D S - B Tr a n s m i t t e r . Th e Tr a n s p o n d e r Me a s u r e m e n t s Me n u a l l o ws t h e u s e r t o m a k e m e a s u r e m e n t s f o r p o we r , p u l s e wi d t h , r i s e t i m e , f a l l t i m e , s p a c i n g a n d f r e q u e n c y .
Page 78 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o s e l e c t t h e H o r i zo n t a l S c a l e .
Page 79 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5.2. TRANSPONDER MEASUREMENTS MENU (CONT) M e a s u r e m e n t M o d e S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o p e r f o r m a m e a s u r e m e n t o r s e t t h e s c o p e t o vi e w a...
Page 80: Transponder Receiver Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5.3. TRANSPONDER RECEIVER MENU A l l o ws t h e u s e r t o v i e w t h e t r a n s m i s s i o n s f r o m t h e U U T a n d t r a n s m i s s i o n s f r o m t h e Te s t S e t . Th e l a s t 8 r e c e p t i o n s a r e d i s p l a ye d .
Page 81 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5.3. TRANSPONDER RECEIVER MENU (CONT) S C R E E N C O M P O N E N T S D E S C R I P T I O N C a p t u r e S o f t k e y A c c e s e s t h e f o l l o wi n g f u n c t i o n s :...
Page 82 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5.3. TRANSPONDER RECEIVER MENU (CONT) Th e R e c e i ve r D i s p l a y Me n u a l l o ws t h e u s e r t o s e t t h e p a r a m e t e r s f o r t h e s t a t u s o f r e c e p t i o n f r o m t h e U U T o r Te s t S e t : S C R E E N C O M P O N E N T D E S C R I P T I O N...
Page 83 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5.3. TRANSPONDER RECEIVER MENU (CONT) Th e D a t a L o g g i n g Me n u a l l o ws t h e u s e r t o s e t t h e p a r a m e t e r s f o r t h e s t a t u s o f r e c e p t i o n f r o m t h e U U T o r Te s t S e t : S C R E E N C O M P O N E N T D E S C R I P T I O N...
Page 84 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5.3. TRANSPONDER RECEIVER MENU (CONT) F i l t e r e d Ma s k e d S o f t k e y a c c e s s e s a d d i t i o n a l s o f t k e y s wh i c h a l l o w t h e u s e r t o s e l e c t f r o m p r e d e f i n e d m a s k s o r t o c r e a t e c u s t o m Mo d e S m a s k s .
Page 85: Filtered Masked Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5.3.5. Filtered Masked Menu A l l o ws t h e u s e r t o s e l e c t t h e m e s s a g e s t o f i l t e r a n d d i s p l a y i n t h e Tr a n s p o n d e r R e c e i ve r Me n u . S C R E E N C O M P O N E N T D E S C R I P T I O N P r e d e f i n e d M a s k s S o f t k e y...
Page 86: Predefined Masks Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5.3.6. Predefined Masks Menu S C R E E N C O M P O N E N T S D E S C R I P T I O N G r o u p s A l l o ws t h e u s e r t o s e l e c t g r o u p s o f U F a n d D F m e s s a g e s .
Page 87: Customize Mode S Mask Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5.3.7. Customize Mode S Mask Menu S C R E E N C O M P O N E N T S D E S C R I P T I O N N u m b e r A l l o ws t h e u s e r t o e n a b l e / d i s a b l e t h e s e l e c t e d p a t t e r n b i t .
Page 88: Highlight Masked Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5.3.8. Highlight Masked Menu A l l o ws t h e u s e r t o s e l e c t t h e m e s s a g e s t o h i g h l i g h t d u r i n g t h e d i s p l a y o f m e s s a g e s i n t h e Tr a n s p o n d e r R e c e i ve r Me n u .
Page 89: Transponder Test Menu - Single Interrogation
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5.4. TRANSPONDER TEST MENU - SINGLE INTERROGATION Th e Tr a n s p o n d e r Te s t Me n u i n S i n g l e I n t e r r o g a t i o n Mo d e a l l o ws t h e u s e r t o s e t u p t h e Te s t S e t t o t r a n s m i t a Mo d e A , Mo d e C , Mo d e A A l l - C a l l , Mo d e C A l l - C a l l , Mo d e A / Mo d e S A l l - C a l l , Mo d e C / Mo d e S A l l - C a l l , Mo d e S , P 1 - P 2 , P u l s e o r D ME p u l s e p a i r .
Page 90 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o l o a d a s a ve d Tr a n s p o n d e r Te s t .
Page 91 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5.4. TRANSPONDER TEST MENU - SINGLE INTERROGATION (CONT) S i n g l e I n t e r r o g a t i o n M o d e M e n u ( M o d e A) S C R E E N C O M P O N E N T S D E S C R I P T I O N M o d e...
Page 92: Transponder Test Menu - Double Interrogation
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5.5. TRANSPONDER TEST MENU - DOUBLE INTERROGATION Th e Tr a n s p o n d e r Te s t Me n u a l l o ws t h e u s e r t o s e t u p t h e Te s t S e t t o t r a n s m i t a d o u b l e i n t e r r o g a t i o n . I n d o u b l e i n t e r r o g a t i o n m o d e b o t h m e s s a g e s a r e t r a n s m i t t e d o n t h e t o p a n t e n n a .
Page 93 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S C R E E N C O M P O N E N T S D E S C R I P T I O N A c c e s s e s t h e f o l l o wi n g : I n s t r u m e n t S e t t i n g s S o f t k e y...
Page 94 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5.5 TRANSPONDER TEST MENU - DOUBLE INTERROGATION (CONT) S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o s e l e c t t h e I n t e r r o g a t i o n Mo d e .
Page 95 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5.5 TRANSPONDER TEST MENU - DOUBLE INTERROGATION (CONT) D o u b l e I n t e r r o g a t i o n M e n u S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o s e l e c t t h e P 1 t o P 1 S p a c i n g , I n t e r l a c e...
Page 96 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5.5. TRANSPONDER TEST MENU - DOUBLE INTERROGATION (CONT) P u l s e S e t t i n g s M e n u 1 - 2 - 3 P a g e 6 1 S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 97: Transponder Test Menu - Interrogation Table
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5.6. TRANSPONDER TEST MENU - INTERROGATION TABLE Th e Tr a n s p o n d e r Te s t Me n u a l l o ws t h e u s e r t o s e t u p t h e Te s t S e t t o t r a n s m i t a b l o c k t r a n s m i s s i o n . S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o s e l e c t t h e Te s t Mo d e .
Page 98 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S C R E E N C O M P O N E N T S D E S C R I P T I O N A c c e s s e s t h e f o l l o wi n g : I n s t r u m e n t S e t t i n g s S o f t k e y...
Page 99 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5.6 TRANSPONDER TEST MENU - INTERROGATION TABLE (CONT) I n t e r r o g a t i o n T a b l e M e n u S C R E E N C O M P O N E N T D E S C R I P T I O N A l l o ws t h e u s e r t o a d d a n e w b l o c k .
Page 100 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5.6 TRANSPONDER TEST MENU - INTERROGATION TABLE (CONT) I n t e r r o g a t i o n P u l s e S e t t i n g s M e n u 1 - 2 - 3 P a g e 6 5 S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 101 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5.6 TRANSPONDER TEST MENU - INTERROGATION TABLE (CONT) I n t e r r o g a t i o n T a b l e F r a m e D e t a i l s M e n u 1 - 2 - 3 P a g e 6 6 S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 102: Transponder Test Menu - Block Transmission
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5.7. TRANSPONDER TEST MENU - BLOCK TRANSMISSION Th e Tr a n s p o n d e r B l o c k Tr a n s m i s s i o n Me n u a l l o ws t h e u s e r t o s e t u p t h e A TC- 5 0 0 0 N G t o t r a n s m i t a b l o c k o f 1 0 3 0 i n t e r r o g a t i o n s .
Page 103 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S C R E E N C O M P O N E N T S D E S C R I P T I O N D i s p l a y s t h e Tr a n s p o n d e r B l o c k Tr a n s m i s s i o n Me n u t o a l l o w B l o c k T r a n s m i s s i o n S o f t k e y...
Page 104 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5.7. TRANSPONDER TEST MENU - BLOCK TRANSMISSION (CONT) T r a n s p o n d e r B l o c k T r a n s m i s s i o n M e n u S C R E E N C O M P O N E N T D E S C R I P T I O N A l l o ws t h e u s e r t o a d d a n e w b l o c k .
Page 105: Transponder Test Menu - Interrogation With Cw
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5.8. TRANSPONDER TEST MENU - INTERROGATION WITH CW Th e Tr a n s p o n d e r Te s t Me n u a l l o ws t h e u s e r t o s e t u p t h e Te s t S e t t o t r a n s m i t a b l o c k t r a n s m i s s i o n . S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o s e l e c t t h e Te s t Mo d e .
Page 106 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o s e l e c t t h e S t a r t ( O n ) o r / S t o p ( O f f ) T x S o f t k e y...
Page 107: Dme Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.6. DME MENU Th e D ME Me n u a l l o ws t h e u s e r t o s e l e c t b e t we e n t h e S e t t i n g s , Me a s u r e m e n t s o r D ME Te s t Me n u f o r D ME t e s t i n g .
Page 108: Dme Settings Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.6.1. DME SETTINGS MENU A l l o ws t h e u s e r t o c o n f i g u r e m o d u l e s i n t h e Te s t S e t f o r D ME t e s t s . Th e D ME S e t t i n g s Me n u i s u s e d f o r t e s t i n g a n d t r o u b l e s h o o t i n g o f t h e Te s t S e t .
Page 109 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.6.1 DME SETTINGS MENU (CONT) S C R E E N C O M P O N E N T D E S C R I P T I O N A l l o ws t h e u s e r t o s e t a l l h a r d wa r e t o t h e F a c t o r y d e f a u l t F a c t o r y S e t u p S o f t k e y...
Page 110: Dme Measurements Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.6.2. DME MEASUREMENTS MENU A l l o ws t h e u s e r t o v i e w t h e p u l s e s f r o m t h e D ME . Th e D ME Me a s u re m e n t s Me n u a l l o ws t h e u s e r t o m a k e m e a s u r e m e n t s f o r p o we r , p u l s e wi d t h , r i s e t i m e , f a l l t i m e , s p a c i n g a n d f r e q u e n c y.
Page 111 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o s e t t h e f i e l d s t o p r e s e t l e ve l s a n d P r e s e t S o f t k e y...
Page 112 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.6.2 DME MEASUREMENTS MENU (CONT) M e a s u r e m e n t M o d e S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o p e r f o r m a m e a s u r e m e n t o r s e t t h e s c o p e t o...
Page 113 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o s e l e c t t h e C h a n n e l 1 s e l e c t i o n .
Page 114: Dme Test Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.6.3. DME TEST MENU Th e D ME Te s t Me n u a l l o ws t h e u s e r t o d e f i n e t h e D ME Te s t s c e n a r i o . S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o s e l e c t t h e D ME C h a n n e l .
Page 115 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o s e l e c t t h e I n t e r r o g a t i o n P u l s e t o b e M e a s u r e d P u l s e - P u l s e...
Page 116 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.6.3 DME TEST MENU (CONT) S C R E E N C O M P O N E N T D E S C R I P T I O N A l l o ws t h e u s e r t o s e l e c t a s t o r e d D ME Te s t .
Page 117 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S C R E E N C O M P O N E N T D E S C R I P T I O N A l l o ws t h e u s e r t o s e l e c t t h e E c h o s e t t i n g s .
Page 118: Uat Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.6.4. UAT MENU Th e U A T Me n u a l l o ws t h e u s e r t o s e l e c t b e t we e n t h e S e t t i n g s , R e c e i vi n g S t a t i o n , R e c e i ve r o r S c e n a r i o Me n u f o r U A T t e s t i n g .
Page 119: Uat Settings Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.6.5. UAT SETTINGS MENU A l l o ws t h e u s e r t o c o n f i g u r e t h e Tr a n s m i t t e r , R e c e i ve r a n d A n t e n n a S i m u l a t o r m o d u l e s i n t h e Te s t S e t f o r U A T t e s t s .
Page 120: Uat Receiving Station Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.6.6. UAT RECEIVING STATION MENU Th e U A T R e c e i v i n g S t a t i o n a l l o ws t h e u s e r t o s e l e c t t h e R e c e i vi n g S t a t i o n p o s i t i o n i n f o r m a t i o n . S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o s e l e c t t h e Mo d e S A d d r e s s ( H e xa d e c i m a l ) .
Page 121: Uat Receiver Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.6.7. UAT RECEIVER MENU A l l o ws t h e u s e r t o v i e w t h e t r a n s m i s s i o n s f r o m t h e U U T a n d t r a n s m i s s i o n s f r o m t h e Te s t S e t. Th e l a s t 8 r e c e p t i o n s a r e d i s p l a ye d .
Page 122 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.6.7 UAT RECEIVER MENU (CONT) Th e C a p t u r e S o f t e k y a c c e s s e s a a d d i t i o n a l s o f t k e y s wh i c h a r e u s e d t o s e l e c t wh i c h i n t e r r o g a t i o n m e s s a g e s a r e c a p t u r e d .
Page 123 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.6.7 UAT RECEIVER MENU (CONT) S C R E E N C O M P O N E N T S D E S C R I P T I O N D i s p l a y S o f t k e y A l l o ws t h e u s e r t o s e t t h e p a r a m e t e r s f o r t h e s t a t u s o f...
Page 124 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.6.7 UAT RECEIVER MENU (CONT) Th e D a t a L o g g i n g S o f t k e y Me n u a l l o ws t h e u s e r t o s e t t h e p a r a m e t e r s f o r t h e s t a t u s o f r e c e p t i o n f r o m t h e U U T o r Te s t S e t .
Page 125 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.6.7 UAT RECEIVER MENU (CONT) S C R E E N C O M P O N E N T S D E S C R I P T I O N F i l t e r e d M a s k e d S o f t k e y D i s p l a y s t h e P r e d e f i n e d Ma s k s Me n u .
Page 126: Filtered Masked Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.6.7.9. Filtered Masked Menu A l l o ws t h e u s e r t o s e l e c t t h e m e s s a g e s t o f i l t e r a n d d i s p l a y i n t h e Tr a n s p o n d e r R e c e i ve r Me n u . S C R E E N C O M P O N E N T S D E S C R I P T I O N P r e d e f i n e d M a s k s S o f t k e y...
Page 127: Predefined Masks Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.6.7.10. Predefined Masks Menu S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o s e l e c t g r o u p s o f U F a n d D F m e s s a g e s .
Page 128: Customize Mode S Mask Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.6.7.11. Customize Mode S Mask Menu S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o e n a b l e / d i s a b l e t h e s e l e c t e d p a t t e r n b i t .
Page 129: Highlight Masked Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.6.7.12. Highlight Masked Menu A l l o ws t h e u s e r t o s e l e c t t h e m e s s a g e s t o h i g h l i g h t d u r i n g t h e d i s p l a y o f m e s s a g e s i n t h e R e c e i ve r Me n u .
Page 130: Uat Scenario Menu - Normal Mode
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.6.8. UAT SCENARIO MENU - NORMAL MODE Th e U A T S c e n a r i o a l l o ws t h e u s e r t o d e f i n e U A T s c e n a r i o wi t h s t a t i c a n d d y n a m i c t a r g e t s . N O T E : W H E N D E F I N I N G T AR G E T S AU T O M AT I C AL L Y T H E T O U C H S C R E E N S O F T W AR E S T AR T S AT M S O 7 5 2 AN D S P AC E S T H E T AR G E T S AT T H E S P E C I F I E D M S O...
Page 131 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o s e l e c t t h e f o l l o wi n g p a r a m e t e r s f o r t h e S t a t i c T a r g e t s...
Page 132: System Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.7. SYSTEM MENU Th e S ys t e m Me n u a l l o ws t h e u s e r t o s e t d i f f e r e n t s ys t e m p a r a m e t e r s ( i . e . , G P I B a d d r e s s , P r o d u c t K e y, S c o p e P o r t O u t p u t s , e t c .
Page 133 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o s e l e c t t h e S c o p e P o r t 1 s i g n a l f r o m m u l t i p l e S c o p e P o r t 1...
Page 134: Software Update Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.7.1. SOFTWARE UPDATE MENU A l l o ws t h e u s e r t o u p d a t e t h e D S P s o f t wa r e o r t h e F P G A f i r m wa r e . S o f t w a r e U p d a t e P r o c e s s : K e r n e l a n d To u c h S c r e e n s o f t wa r e a r e u p d a t e d .
Page 135 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S C R E E N C O M P O N E N T S D E S C R I P T I O N P r o g r a m s a l l t h e F P G A s a n d D S P s t h a t h a ve t h e p r o g r a m m i n g E x e c u t e S o f t k e y...
Page 136: Network Connections Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.7.2. NETWORK CONNECTIONS MENU Th e N e t wo r k C o n n e c t i o n s Me n u d i s p l a y s t h e c u r r e n t n e t wo r k s e t t i n g s a n d a l l o ws c h a n g i n g t h e n e t wo r k s e t t i n g s .
Page 137 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.7.2 NETWORK CONNECTIONS MENU (CONT) Th e i n t e r n a l D S P I P a d d r e s s c a n b e c h a n g e d f r o m t h e f a c t o r y d e f a u l t o f 1 9 2 . 1 6 8 . 0 . 1 . Th e i n t e r n a l D S P I P a d d r e s s s h o u l d o n l y b e c h a n g e d i f t h e I P a d d r e s s i s n e e d e d b y t h e e xt e r n a l L A N c o n n e c t i o n s .
Page 138 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.7.2 NETWORK CONNECTIONS MENU (CONT) To c h a n g e t h e I P a d d r e s s t o a s t a t i c I P s e l e c t t h e U s e t h e f o l l o wi n g I P A d d r e s s g r o u p b o x. E n t e r t h e I P a d d r e s s d e s i r e d f o r t h e i n t e r n a l D S P c o n n e c t i o n .
Page 139: Configuration Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.7.3. CONFIGURATION MENU A l l o ws t h e u s e r t o s e l e c t t h e 4 2 9 i n p u t c h a n n e l p o s i t i o n a n d l a b e l . S C R E E N C O M P O N E N T S D E S C R I P T I O N A l l o ws t h e u s e r t o s e l e c t t h e p o s i t i o n o f t h e :...
Page 140: Calibration Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.7.4. CALIBRATION MENU A l l o ws t h e u s e r t o v i e w t h e l a s t c a l i b r a t i o n d a t e a n d r e s u l t . 1 - 2 - 3 P a g e 1 0 5 S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 141: Support Menu
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.8. SUPPORT MENU Th e S u p p o r t Me n u d i s p l a ys t h e A e r o f l e x C u s t o m e r S e r vi c e c o n t a c t i n f o r m a t i o n . 1 - 2 - 3 P a g e 1 0 6 S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 142: Operating Procedures And Test Configurations
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G OPERATING PROCEDURES AND TEST CONFIGURATIONS 4.1. OPERATING PROCEDRUES 4.1.1. HOW TO CHANGE THE GPIB ADDRESS G o t o t h e Ma i n Me n u P r e s s t h e S y s t e m Me n u S o f t k e y t o d i s p l a y t h e S ys t e m Me n u .
Page 143: How To Change The Transmitter Frequency
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 4.1.2. HOW TO CHANGE THE TRANSMITTER FREQUENCY G o t o t h e Ma i n Me n u P r e s s t h e T C A S S o f t k e y t o d i s p l a y t h e TC A S Ma i n Me n u .
Page 144: How To Set A Scope Output
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 4.1.3. HOW TO SET A SCOPE OUTPUT G o t o t h e Ma i n Me n u S e l e c t t h e S y s t e m Me n u S o f t k e y t o d i s p l a y t h e S ys t e m Me n u .
Page 145: How To Program The Dsp Software Or Fpga Firmware
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 4.1.4. HOW TO PROGRAM THE DSP SOFTWARE OR FPGA FIRMWARE G o t o t h e Ma i n Me n u P r e s s t h e S y s t e m Me n u S o f t k e y t o d i s p l a y t h e S ys t e m Me n u .
Page 146: How To Enter The Own Aircraft Information
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 4.1.5. HOW TO ENTER THE OWN AIRCRAFT INFORMATION G o t o t h e Ma i n Me n u P r e s s t h e U A T S o f t k e y t o d i s p l a y t h e U A T Ma i n Me n u .
Page 147: Test Configurations
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 4.2. TEST CONFIGURATIONS 4.2.1. TRANSPONDER ATC/MODE S/ELS/EHS TEST CONFIGURATION 1 - 2 - 4 P a g e 6 S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 148: Transponder Ads-B Out (1090Es) Test Configuration
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 4.2.2. TRANSPONDER ADS-B OUT (1090ES) TEST CONFIGURATION 1 - 2 - 4 P a g e 7 S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 149 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G TH I S P A G E I N TE N TI O N A L L Y L E F T B L A N K . 1 - 2 - 4 P a g e 8 S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 150: Remote Operation
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G REMOTE OPERATION SECTION TABLE OF CONTENTS Section # Title Page REMOTE OPERATION ..................................1 5.1. OVERVIEW ....................................
Page 151 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G SECTION TABLE OF CONTENTS Section # Title Page 5.5. RTCA/DO-260 TEST COMMANDS ..............................23 5.5.1. GENERATOR PARAMETERS ..............................
Page 152 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G SECTION TABLE OF CONTENTS Section # Title Page 5.5.7.5. PREAMBLE VALIDATION TEST PARAMETERS ........................ 32 5.5.7.5.1.
Page 153 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G SECTION TABLE OF CONTENTS Section # Title Page 5.6.2. INTRUDERS DEFINITION PARAMETERS ........................... 39 5.6.2.1. ALTITUDE MODE ................................
Page 154 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G SECTION TABLE OF CONTENTS Section # Title Page 5.6.2.3.1.34. UAT IN ................................49 5.6.2.3.2. AIRCRAFT OPERATIONAL STATUS MESSAGE SCHEDULE ..................49 5.6.2.3.2.1.
Page 155 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G SECTION TABLE OF CONTENTS Section # Title Page 5.6.2.14.1. ALTITUDE ................................59 5.6.2.14.2. BEARING ................................59 5.6.2.14.3.
Page 156 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G SECTION TABLE OF CONTENTS Section # Title Page 5.6.2.19.2.1. DYNAMIC TARGET STATE AND STATUS SCHEDULE ..................69 5.6.2.19.2.2.
Page 157 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G SECTION TABLE OF CONTENTS Section # Title Page 5.6.3.17. STATIC TEST MODE ............................... 78 5.6.3.18. STOP ....................................
Page 158 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G SECTION TABLE OF CONTENTS Section # Title Page 5.6.4.16.1. PAYLOAD GPS ANTENNA AXIS ..........................87 5.6.4.16.2.
Page 159 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G SECTION TABLE OF CONTENTS Section # Title Page 5.8.7. INTERROGATION TOP ANTENNA POWER ..........................97 5.8.8.
Page 160 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G SECTION TABLE OF CONTENTS Section # Title Page 5.8.17.3.1. BURST MODE ............................... 106 5.8.17.3.1.1. BURST OPERATION ENABLE ......................... 106 5.8.17.3.1.2.
Page 161 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G SECTION TABLE OF CONTENTS Section # Title Page 5.10.1. ACCELERATION ..................................116 5.10.2. CABLE LOSS ................................... 116 5.10.3.
Page 162: Overview
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.1. OVERVIEW Functional capabilities within the Unit for specific customers are provided by means of customer specific product keys (for instance UAT functionality although commands are defined, is only enabled for customers that have hardware and software UAT capability).
Page 163 Example: Send “:ATC:SCE:TYPE XPDR\r” to set the unit for transponder scenario, then send “:ATC:SET:FACT XPDR\r” to reset the generator to the default for that mode of operation. The ATC-5000NG accepts the following GPIB commands: *IDN? This command returns Aeroflex;ATC-5000NG RF Test Set;138156 *CLS This command resets the status byte and the Touchscreen error log.
Page 164: Measurement Commands
5.2. MEASUREMENT COMMANDS This set of commands allows the user to query the ATC-5000NG to perform measurements on the received signal from the UUT. The ATC-5000NG can perform frequency, power and pulse characteristic measurements on both 1030 and 1090 MHz signals.
Page 165: Pulse
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.2.4. PULSE Command Syntax: {:ATC |:ATC5000NG}{:MEA |:MEASURE}{:SET |:SETTINGS}{:PUL |:PULSE}SP<value>CR Description: This command sets the measurement routine to sample the selected pulse. Pulse selected to sample interrogation is ignored when the scenario type selected is XPDR.
Page 166: Spr
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.2.5.3. PULSE RISETIME REQUEST Command Syntax: {:ATC |:ATC5000NG}{:MEA |:MEASURE}{:PUL |:PULSE}{:RISE?} CR Description: This command returns the rise time of the selected pulse. Example: :ATC:MEA:PUL:RISE?\r Return:...
Page 167 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.2.7.2. DBM LEVEL Command Syntax: {:ATC |:ATC5000NG}{:MEA |:MEASURE}{:SET |:SETTINGS}{:TRIGGER |:TRIG}{:LDBM}SP<numeric>CR Description: This command sets the trigger level in dBm if trigger source is set to log video. Numeric: 15 to 60 dBm (decimal ASCII) Example:...
Page 168: Own Aircraft Commands
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.3. OWN AIRCRAFT COMMANDS This set of commands allow the user to set the own aircraft information remotely. 5.3.1.
Page 169: Receiver Commands
A T C - 5 0 0 0 N G 5.4. RECEIVER COMMANDS This set of commands allows the user to set the ATC-5000NG to perform various receiver functions (select received messages, enable/disable data logging, read logged data, etc.). 5.4.1.
Page 170 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G ATCRBS Replies: SW Ver. 17.08.1701 and below: Byte 2: High Nibble Bit7-4 (Zero); Low Nibble Bit 3-0 (C1 A1 C2 A2) Byte 3: (C4 A4 B1 D1 B2 D2 B4 D4) Byte 4 to 15: All 0’s SW Ver.
Page 171: Mask
{:ATC |:ATC5000NG}{:RCV |:RCVR}{:ST |:STATUS}?CR Description: This command returns a byte with the status of all eight receivers within the ATC-5000NG (receivers in this context means any of the 8 defined functional “receivers” below - not physical RF Hardware receivers). A “1” for the receiver associated bit means that the receiver is receiving messages.
Page 172: Utc Time
5.5. RTCA/DO-260 TEST COMMANDS These commands allow the definition of different RTCA/DO-260 tests. The ATC-5000NG has implemented the following test types: Normal Test, Bit Failures Special Test, Altered Preamble Special Test, Overlapping Pulse Special Test, Confidence Test and Preamble Validation Test.
Page 173 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.5.1.4. ATCRBS PULSE PARAMETERS 5.5.1.4.1. DELTA PULSE POSITION Command Syntax: {:ATC |:ATC5000NG}{:DO260}{:TYPE}{:NORMAL}{:PULSE}{:ATCRBS:CH:}{ 1 | 2 | 3 | 4 | 5 | 6}{:PF1 |:PC1 |:PA1 |:PC2 |:PA2 |:PC4 |:PA4 |:PB1 |:PD1 |:PB2 |:PD2 |:PB4 |:PD4 |:PF2}{:DPOS}SP<numeric>CR Description:...
Page 174 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.5.1.6. DELAY Command Syntax: {:ATC |:ATC5000NG}{:DO260}{:TYPE}{:NORMAL } {:GENS}{:GENA |:GENB |:GENC |:GEND |:GENE |:GENF} {:DELAY }SP<numeric>CR {:ATC |:ATC5000NG}{:DO260}{:TYPE}{:OVERLAPPINGPULSE |:OVERLAP |:ALTEREDPREAMBLE |:ALT |:BITFAILURES |:BITF |:PREAMBLEVAL |:PREA } {:GENS}{:GENA |:GENC } {:DELAY }SP<numeric>CR...
Page 175 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.5.1.10. MODE S PULSE PARAMETERS 5.5.1.10.1. PREAMBLE DELTA PULSE POSITION Command Syntax: {:ATC |:ATC5000NG}{:DO260}{:TYPE}{:NORMAL}{:PULSE}{:MODES:CH:}{ 1 | 2 | 3 | 4 | 5 | 6}{:P2 |:P3 |:P4 }{:DPOS}SP<numeric>CR Description: This command sets the delta position of the selected Mode S pulse on the selected generator.
Page 176: Load
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.5.1.13. RANDOM STARTING POSITION ON/OFF Command Syntax: {:ATC |:ATC5000NG}{:DO260}{:TYPE}{:NORMAL } {:GENS}{:GENA |:GENB |:GENC |:GEND |:GENE |:GENF } {:RSPOS}SP{ON | OFF}CR Description: This command enables or disables the random starting position generation of the pulse to transmit using the selected generator.
Page 177: Number Of Transmissions
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.5.5. RESET Command Syntax: {:ATC |:ATC5000NG}{:DO260}{:RESET}CR Description: This command initializes the DO-260 test to the default values. Default: Attribute Value...
Page 178: Special Test
SPECIAL TEST The follow set of commands allow the user to setup some specific tests in RTCA DO-260 document. The special tests provided by the ATC-5000NG are Altered Preamble, BIT Failure, Confidence Test, Overlapping and Preamble Validation. 5.5.7.1. ALTERED PREAMBLE PARAMETERS 5.5.7.1.1.
Page 179 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.5.7.2. BIT FAILURE PARAMETERS 5.5.7.2.1. FIRST BAD CHIP Command Syntax: {:ATC |:ATC5000NG}{:DO260}{:TYPE}{:BITFAILURES |:BITF } {:CHIPS}{:BFIRST}SP<numeric>CR Description: This command sets the first bit of the bad chips pulse.
Page 180 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.5.7.3. CONFIDENCE TEST PARAMETERS 5.5.7.3.1. BAD CHIPS Command Syntax: {:ATC |:ATC5000NG}{:DO260}{:TYPE}{:CONFIDENCE |:CONF } {:BADP}{:CHIPS}SP<numeric>[,<numeric>[,<numeric>[,<numeric>[,<numeric>]]]]CR Description: This command sets the list of bits with bad chip pulses.
Page 181 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.5.7.5. PREAMBLE VALIDATION TEST PARAMETERS 5.5.7.5.1. DELTA AMPLITUDE Command Syntax: {:ATC |:ATC5000NG}{:DO260}{:TYPE}{:PREAMBLEVAL |:PREA } {:CHIPS}{:DAMP}SP<numeric>CR Description: This command sets the delta amplitude in dB for energy bits of the pulse.
Page 182: Start
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.5.7.5.6. LAST NO ENERGY CHIP Command Syntax: {:ATC |:ATC5000NG}{:DO260}{:TYPE}{:PREAMBLEVAL |:PREA } {:CHIPS}{:NLAST}SP<numeric>CR Description: This command sets the last no energy bit of the message. Numeric: 0 for no bad chip (decimal ASCII) 1 to 112 if the reference is a long Mode S (decimal ASCII)
Page 183: Trigger Parameters
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.5.11. TRIGGER PARAMETERS 5.5.11.1. MODE Command Syntax: {:ATC |:ATC5000NG}{:DO260}{:TIMING}{:TRIGGER |:TRIG}{:MODE}SP<numeric>CR Description: This command sets the trigger mode. Delay+ delays positively all the enabled generators according with each delay amount from the trigger source.
Page 184: Block Transmission
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.5.12. BLOCK TRANSMISSION This set of commands allows the user to define a transmission block of messages to periodically transmit to the unit under test.
Page 185 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.5.12.2. LOAD Command Syntax: {:ATC |:ATC5000NG}{ :TXBLOCK}{:LOAD}SP<filename>}CR Description: This command loads a CSV scenario file (specified filename) from the internal storage area. A”*”...
Page 186 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.5.12.6. RUN TIME REQUEST Command Syntax: {:ATC |:ATC5000NG}{:TXBLOCK}{:TI |:TIME}?CR Description: This command returns the current scenario run time. Return Value: decimal ASCII value.
Page 187: Scenario Commands
SCENARIO COMMANDS This set of commands allows the user to define dynamic and static intruders for Multi-Receiver, and UAT scenarios. The Multi-Receiver Menu and UAT Menu are options of the ATC-5000NG and require product key and calibration to enable. 5.6.1.
Page 188: Intruders Definition Parameters
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2. INTRUDERS DEFINITION PARAMETERS 5.6.2.1. ALTITUDE MODE Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC: |:DYN: |:DYNAMIC:}<intruder no>{:AMODE}SP{GILHAM | BINARY}CR Description: This command sets the altitude data mode to either Gilham or Binary.
Page 189 5.6.2.2.2. AIRBORNE POSITION MESSAGE SCHEDULE Airborne or Surface Position squitters are transmitted by the ATC-5000NG at a rate of 0.5 seconds. The CPR encoding is alternated every 0.5 second unless the user specifies to only transmit odd or even encoding.
Page 190 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.2.2.1.2. INTERVAL QUANTITY Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:DYN: |:DYNAMIC:}<intruder no>{:SPOSEVEN |:SPOSODD}{:NINT |:NINTERVALS}SP<numeric>CR Description: This command sets the number of position even or odd squitter message intervals for the selected intruder.
Page 191 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.3.1.2. AIR REFERENCED VELOCITY Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC: |:DYN: |:DYNAMIC:}<intruder no>{:SAOS}{:ARV}SP<numeric>CR Description: This command sets the selected intruder aircraft operational status squitter air referenced velocity field to the specified value.
Page 192 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.3.1.5. BAROMETRIC ALTITUDE INTEGRITY CODE Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC: |:DYN: |:DYNAMIC:}<intruder no>{:SAOS}{:NICB}SP<numeric>CR Description: This command sets the selected intruder aircraft operational status squitter barometric altitude integrity code field to the specified value.
Page 193 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.3.1.10. HORIZONTAL REFERENCE DIRECTION Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC: |:DYN: |:DYNAMIC:}<intruder no>{:SAOS}{:HRD}SP<numeric>CR Description: This command sets the selected intruder aircraft operational status squitter horizontal reference direction field to the specified value.
Page 194 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.3.1.14. MODE SUBTYPE Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC: |:DYN: |:DYNAMIC:}<intruder no>{:SAOS}{:OM}SP<numeric>CR Description: This command sets the selected intruder aircraft operational status squitter operational mode subtype field to the specified value.
Page 195 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.3.1.18. NIC SUPPLEMENT-B Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC: |:DYN: |:DYNAMIC:}<intruder no>{:SAOS}{:NISB}SP<numeric>CR Description: This command sets the selected intruder aircraft operational status squitter NIC Supplement-B field to the specified value.
Page 196 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.3.1.23. RESERVED FOR ADS-R FLAG Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC: |:DYN: |:DYNAMIC:}<intruder no>{:SAOS}{:ADR}SP<numeric>CR Description: This command sets the selected intruder aircraft operational status squitter reserved for ADS-R flag field to the specified value.
Page 197 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.3.1.28. SOURCE INTEGRITY LEVEL (SIL) SUPPLEMENT Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC: |:DYN: |:DYNAMIC:}<intruder no>{:SAOS}{:SILS}SP<numeric>CR Description: This command sets the selected intruder aircraft operational status squitter SIL supplement field to the specified value.
Page 198 5.6.2.3.2. AIRCRAFT OPERATIONAL STATUS MESSAGE SCHEDULE Airborne Operational Status squitter is transmitted by the ATC-5000NG at a rate of 2.0 seconds. Dynamic intruders (targets) allow definition of multiple time intervals where the Airborne Operation Status squitter can be enabled or disabled.
Page 199 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.3.2.1.4. INTERVAL STOP TIME Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:DYN: |:DYNAMIC:}<intruder no>{:SAOS}{:INT: |:INTERVAL:}<interval number>{:END}SP<numeric>CR Description: This command sets the stop time for the selected aircraft operational status squitter message interval for the selected intruder.
Page 200 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.4.1.3. MULTIPLE THREAT ENCOUNTER Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT:|:STATIC: |:DYN: |:DYNAMIC:}<intruder no>{:SAS}{:MTE}SP<numeric>CR Description: This command sets the selected intruder Aircraft Status TCAS Resolution Advisory squitter MTE field to the specified value, if the intruder is an extended Mode S or an ADS-R and the aircraft status subtype selected is TCAS Resolution Advisory (2).
Page 201 :ATC:SCE:DYN:1:SAS:TTI 2\r 5.6.2.4.2. AIRCRAFT STATUS MESSAGE SCHEDULE Aircraft/Emergency Status squitter is transmitted by the ATC-5000NG at a rate of 1.0 seconds. Dynamic intruders (targets) allow definition of multiple time intervals where the Aircraft/Emergency Status squitter can be enabled or disabled.
Page 202 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.4.2.2. STATIC AIRCRAFT STATUS SCHEDULE 5.6.2.4.2.2.1. INTERVAL ENABLE Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC:}<intruder no>{:SAS}{:ENA |:ENABLE}SP{ON | OFF}CR Description: This command enables or disables the aircraft status squitter message of the specified intruder.
Page 203 :ATC:SCE:DYN:1:IDENTTYPE 3\r 5.6.2.9.2. IDENTIFICATION MESSAGE SCHEDULE Identification squitter is transmitted by the ATC-5000NG at a rate of 5.0 seconds. Dynamic intruders (targets) allow definition of multiple time intervals where the Identification squitter can be enabled or disabled. Static intruders (targets) allow the user to enable or disable the Identification squitter for the entire scenario.
Page 204 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.9.2.1.3. INTERVAL START TIME Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:DYN: |:DYNAMIC:}<intruder no>{:SIDENT}{:INT: |:INTERVAL:}<interval number>{:BEGIN}SP<numeric>CR Description: This command sets the start time for the selected identification squitter message interval for the selected intruder.
Page 205 5.6.2.12. MODE-S ALL CALL REPLY (DF=11) MESSAGE DF11 squitter is transmitted by the ATC-5000NG at a rate of 1.0 seconds. Dynamic intruders (targets) allow definition of multiple time intervals where the DF11 squitter can be enabled or disabled. Static intruders (targets) allow the user to enable or disable the DF11 squitter for the entire scenario.
Page 206 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.13.2. DOWNLINK REQUEST (DR) Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC: |:DYN: |:DYNAMIC:}<intruder no>{:DR}SP<numeric>CR Description: This command sets the DR field for a Mode S intruder. Numeric: 0 to 31 (decimal ASCII) Default:...
Page 207 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.13.7. REPLY INFORMATION (RI; AQ=1) Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC: |:DYN: |:DYNAMIC:}<intruder no>{:RI:AQ1}SP<numeric>CR Description: This command sets the RI field for a Mode S intruder for an AQ=1 reply.
Page 208 NOTE: The intruder can be defined by range and bearing or latitude and longitude. If the intruder is defined using range and bearing, the ATC-5000NG calculates the latitude and longitude of the intruder. If the intruder is defined using latitude and longitude, the ATC-5000NG calculates the range and bearing.
Page 209 NOTE: The intruder can be defined by range and bearing or latitude and longitude. If the intruder is defined using range and bearing, the ATC-5000NG calculates the latitude and longitude of the intruder. If the intruder is defined using latitude and longitude, the ATC-5000NG calculates the range and bearing.
Page 210 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.17. SQUITTER PARAMETERS 5.6.2.17.1. ANTENNA Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC: |:DYN: |:DYNAMIC:}<intruder no>{:SQANT}SP{TOP | BOTTOM | BOTH}CR Description: This command sets if the squitter is transmitted on both antennas simultaneously, top only or bottom only.
Page 211 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.18.2. MOVEMENT MISCELLANEOUS Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC: |:DYN: |:DYNAMIC:}<intruder no>{:MMISC }SP<numeric>CR Description: This command sets the selected intruder to the selected miscellaneous movement, if Movement has been set to miscellaneous.
Page 212 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.19. TARGET STATE AND STATUS MESSAGE The following set of commands allows the user capability of defining for any intruder the Target State and Status squitter. 5.6.2.19.1.
Page 213 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.19.1.5. BACKWARD COMPATIBILITY FLAG Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC: |:DYN: |:DYNAMIC:}<intruder no>{:STARGET}{:BCF}SP<numeric>CR Description: This command sets the selected intruder target state and status squitter backward compatibility flag field to the specified value, if the intruder is an extended Mode S.
Page 214 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.19.1.9. EMERGENCY/PRIORITY STATUS Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC: |:DYN: |:DYNAMIC:}<intruder no>{:STARGET}{:EPS}SP<numeric>CR Description: This command sets the selected intruder target state and status squitter emergency/priority status field to the specified value, if the intruder is an extended Mode S.
Page 215 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.19.1.13. MCP/FCU MODE BITS Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC: |:DYN: |:DYNAMIC:}<intruder no>{:STARGET}{:SMD}SP<numeric>CR Description: This command sets the selected intruder target state and status squitter status of MCP/FCU mode bits field to the specified value, if the intruder is an extended Mode S.
Page 216 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.19.1.17. SOURCE INTEGRITY LEVEL SUPPLEMENT Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC: |:DYN: |:DYNAMIC:}<intruder no>{:STARGET}{:SILS}SP<numeric>CR Description: This command sets the selected intruder target state and status squitter source integrity level supplement field to the specified value, if the intruder is an extended Mode S (DO-260B).
Page 217 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.19.1.22. TARGET HEADING/TRACK INDICATOR Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC: |:DYN: |:DYNAMIC:}<intruder no>{:STARGET}{:THTI}SP<numeric>CR Description: This command sets the selected intruder target state and status squitter target heading/track indicator field to the specified value, if the intruder is an extended Mode S.
Page 218 TARGET STATE AND STATUS MESSAGE SCHEDULE Target State and Status squitter is transmitted by the ATC-5000NG at a rate of 1.0 seconds. Dynamic intruders (targets) allow definition of multiple time intervals where the Target State and Status squitter can be enabled or disabled.
Page 219 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.19.2.1.4. INTERVAL STOP TIME Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:DYN: |:DYNAMIC:}<intruder no>{:STARGET}{:INT: |:INTERVAL:}<interval number>{:END}SP<numeric>CR Description: This command sets the stop time for the selected target state and status squitter message interval for the selected intruder.
Page 220 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.21. VELOCITY MESSAGE The following set of commands allows the user to define the velocity squitter information for any intruder. 5.6.2.21.1.
Page 221 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.21.1.7. INTENT CHANGE FLAG Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC: |:DYN: |:DYNAMIC:}<intruder no>{:VELINTENT}SP<numeric>CR Description: This command sets the selected intruder velocity squitter intent change flag field to the specified value, if the intruder is an extended Mode S.
Page 222 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.21.1.12. SURVEILLANCE INTEGRITY LEVEL Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC: |:DYN: |:DYNAMIC:}<intruder no>{:VELSIL}SP<numeric>CR Description: This command sets the selected intruder velocity squitter surveillance integrity level field to the specified value.
Page 223 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.2.21.1.16. VELOCITY TYPE Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC: |:DYN: |:DYNAMIC:}<intruder no>{:VELTYPE}SP<numeric>CR Description: This command sets the selected intruder velocity squitter to the specified type, if the intruder is an extended Mode S.
Page 224 5.6.2.21.2. VELOCITY MESSAGE SCHEDULE Velocity squitter is transmitted by the ATC-5000NG at a rate of 0.5 seconds. Dynamic intruders (targets) allow definition of multiple time intervals where the Velocity squitter can be enabled or disabled. Static intruders (targets) allow the user to enable or disable the Velocity squitter for the entire scenario.
Page 225: Scenario Parameters
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.3. SCENARIO PARAMETERS The following set of commands allows the user to define some scenario parameters before executing the start of scenario. 5.6.3.1.
Page 226 This command sets the increment used to define the Message Start Opportunities for each UAT ADS-B message defined. If the scenario type selected is MULTI, the <numeric> and <numeric1> are used to define the MSO step for dynamic and static UAT respectively. This command requires ATC-5000NG UAT Hardware. Numeric: 1 to 100 (decimal ASCII)
Page 227 {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:SLA |:SLANT}SP{ON | OFF}CR Description: This command sets the ATC-5000NG to generate targets with actual slant range or horizontal plane range. In slant range mode the altitude difference between the own aircraft and intruder is used for reply delay.
Page 228 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.3.21. SWEEP INTERVAL Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:SWEEP:INTERVAL}SP<numeric>CR Description: This command specifies the sweep interval. This command is valid only for UAT scenario. Numeric: 194 to 994 ms (decimal ASCII) Default:...
Page 229: Uat Ads-B Definition Parameters
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.3.28. UAT TEST MODE PULSE POWER Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:UAT}{:STEST}{:POWER|:POW}SP<numeric>CR Description: This command sets the power level for the UAT test mode selected. This command is valid only for UAT scenario.
Page 230 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.4.2. AIRCRAFT SIZE Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC: |:DYN: |:DYNAMIC:} <intruder no>{:AVSIZE}SP<numeric>CR Description: This command sets the A/V size of the specified intruder. This command is valid only for intruders with AG state grounded.
Page 231 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.4.5. LATERAL AXIS GPS ANTENNA OFFSET Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC: |:DYN: |:DYNAMIC:} <intruder no>{:UAT}{:GPSLAT}SP<numeric>CR Description: This command sets the lateral axis GPS antenna offset of the specified intruder.
Page 232 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.4.8. NAVIGATION INTEGRITY CATEGORY Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC: |:DYN: |:DYNAMIC:} <intruder no>{:NIC}SP<numeric>CR Description: This command sets the NIC of the specified intruder.
Page 233 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.4.12. VERTICAL VELOCITY SOURCE Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC: |:DYN: |:DYNAMIC:}<intruder no>{:VVSOURCE}SP<numeric>CR Description: This command sets the VV source of the specified intruder. The <intruder no> specifies the number of the intruder in the channel grouping specified.
Page 234 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.4.15.3. PAYLOAD TYPE CODE Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:DYN: |:DYNAMIC:}<intruder no>{:UAT}{:ADSB:}<message number>{:PLCODE}SP<numeric>CR Description: This command sets the payload type code of the ADS-B message of the specified intruder. The <intruder no>...
Page 235 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.4.15.8. PAYLOAD MESSAGE SCHEDULE INTERVAL POWER Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:DYN: |:DYNAMIC:}<intruder no>{:UAT}{:ADSB:}<message number>{:INT: |:INTERVAL:}<interval number>{:PWR }SP<numeric>CR Description: This command sets the power level of the ADS-B payload message interval for the selected...
Page 236 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.4.16. UAT STATIC ADS-B PAYLOAD Note: See section 5.11.8. UAT Scenario Definition Example to aid in proper command order to setup the UAT scenario. 5.6.4.16.1.
Page 237 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.4.16.4. BASIC/LONG ADS-B MESSAGE FEC PARITY Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC:}<intruder no>{:PLFEC}SP<numeric>CR Description: This command sets the FEC parity of the specified intruder. This command applies to ADS-B Messages with payload type code ‘11’...
Page 238: Uat Ground Uplink Definition Parameters
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.4.16.9. TARGET STATE PAYLOAD MESSAGE ELEMENT Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC:}<intruder no>{:PLTS}SP<numeric>CR Description: This command sets the intruder state payload message element of the specified intruder. This command applies to ADS-B Messages with payload type code of ‘3’, ‘4’...
Page 239 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.6.5.1.5. SLOT ID Command Syntax: {:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC:}<intruder no>{:UAT}{:GUS}{:SLOTID}SP<numeric>CR Description: This command sets the time slot where the Ground Uplink Message transmission occurs. The <intruder no>...
Page 240: Settings Commands
The following set of commands allows the user to modify the Generator Frequency, Modulation (CW/Pulse), Factory Setting (Factory Reset), ATC-5000NG Scope Port and Generator Power. These commands are used for troubleshooting the ATC-5000NG and for calibration and factory testing of the ATC-5000NG. 5.7.1.
Page 241: Tx Generator Parameters
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.7.3. TX GENERATOR PARAMETERS N O T E : T h e G e n e r a t o r c o m m a n d s a r e f o r u s e i n t h e R T C A/ D O- 2 6 0 T e s t m o d e a n d F a c t o r y c a l i b r a t i o n O N L Y .
Page 242 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.7.3.3. PATH Command Syntax: {:ATC |:ATC5000NG}{:SET |:SETTINGS}{:GENA |:GENB |:GENC |:GEND |:GENE |:GENF}{:PATH}SP<TOP | BOTTOM>CR Description: This command sets the selected generator path to the top or bottom antenna.
Page 243 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.7.3.5. RISE/FALL TIME Command Syntax: {:ATC |:ATC5000NG}{:SET |:SETTINGS}{:GENA |:GENC |:GENE }{:RISE |:RISEFALL}SP<numeric>CR Description: This command sets the selected generator pulse rise and fall time. A”*” is returned if the command is able to complete successfully or “?”...
Page 244: Transponder Commands
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.8. TRANSPONDER COMMANDS This set of commands allows the user to define the Unit to perform Transponder testing. 5.8.1.
Page 245: Interrogation Frequency
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.8.3.4. INTERFERENCE PULSE ENABLE Command Syntax: {:ATC |:ATC5000NG}{:XPDR}{:INTERFERENCE |:INTERF}SP{ON |OFF}CR Description: This command turns on or off the interference pulse. This command is valid only for single interrogation, double interrogation and interrogation table.
Page 246: Interrogation Test Type
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.8.6. INTERROGATION TEST TYPE Command Syntax: {:ATC |:ATC5000NG}{:XPDR}{:TYPE}SP<numeric>CR Description: This command sets the transponder interrogation test type. This command must be sent before to define the pulse parameters.
Page 247: Scope Trigger Offset
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.8.12. SCOPE TRIGGER OFFSET Command Syntax: {:ATC |:ATC5000NG}{:XPDR:SCOPE:INTERR:OFFSET}SP<numeric>CR Description: This command sets the scope trigger offset from P1 of the interrogation. Numeric: -1 to 600 usec (Decimal ASCII) Default:...
Page 248: Transmission Modes
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.8.17. TRANSMISSION MODES 5.8.17.1. BLOCK TRANSMISSION This set of commands allows the user to define block of messages to be transmitted. 5.8.17.1.1.
Page 249 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.8.17.1.1.5. TRANSMISSIONS Command Syntax: {:ATC |:ATC5000NG}{ :XPDR}{ :TXBLOCK}{:TRANSMISSIONS|:TRANS}SP{NOLIMIT|<numeric>}CR Description: This command sets the total number of blocks transmission. Numeric: 1 to 50000 (decimal ASCII) Default:...
Page 250 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.8.17.1.2.5. TYPE Command Syntax: {:ATC |:ATC5000NG}{:XPDR}{:TXBLOCK:}<message number>{:TYPE} SP<numeric>[,<numeric1>]CR Description: This command sets the type of the message selected. The optional argument <numeric1> defines the ATCRBS Interrogation type.
Page 251 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.8.17.2.2. INTERLACED MODE This set of commands allows the user to define an interlace mode. The illustration below demonstrates how the interlaced ratio operates.
Page 252 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.8.17.2.3. MODE Command Syntax: {:ATC |:ATC5000NG}{:XPDR}{:DBL:}<interrogation number>{:MOD |:MODE}SP<numeric>CR Description: This command sets the transponder interrogation mode of the selected double interrogation. <interrogation number>...
Page 253 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.8.17.2.7. PULSE POWER LEVEL Command Syntax: {:ATC |:ATC5000NG}{:XPDR}{:DBL:}<interrogation number>{:POW |:POWER}SP<numeric>CR Description: This command sets the antenna power for the top antenna of the selected double interrogation. <interrogation number>...
Page 254 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.8.17.2.9. PULSE REPETITION FREQUENCY (PRF) Command Syntax: {:ATC |:ATC5000NG}{:XPDR}{:DBL:} <interrogation number>{:PRF }SP<numeric>CR Description: This command sets the pulse repetition rate (PRF) of the selected double interrogation. <interrogation number>...
Page 255 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.8.17.2.13. SYNCHRONIZATION Command Syntax: {:ATC |:ATC5000NG}{:XPDR}{:DBL}{:SYNC}SP<numeric>CR Description: This command allows selecting the interrogation number for synchronization. The measured UUT values are obtained from the reply associated with the interrogation selected for synchronization.
Page 256 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.8.17.3.2. NUMBER OF INTERROGATIONS Command Syntax: {:ATC |:ATC5000NG}{:XPDR}{:ITABLE}{:NINT}SP<numeric>CR Description: This command sets the number of interrogations of the interrogation table. Numeric: 1 to 1000 (decimal ASCII) Default:...
Page 257 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.8.17.3.7. TABLE ENTRY ENABLE Command Syntax: {:ATC |:ATC5000NG}{:XPDR}{:ITABLE:}<table entry>{:ENABLE}SP{ON | OFF}CR Description: This command turns on or off the interrogation of the selected table entry. Table Entry: 1-1000 (Decimal ASCII) Default:...
Page 258 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.8.17.3.11. TABLE ENTRY PULSE PARAMETER Command Syntax: {:ATC |:ATC5000NG}{:XPDR}{:ITABLE:}<table entry>{:PUL: |:PULSE:}<pulse>SP<value>CR Description: This command sets the selected pulse parameter of the selected table entry. Table Entry: 1 to 1000 (decimal ASCII) Pulse/Value:...
Page 259 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.8.17.4. SINGLE INTERROGATION This set of commands allows the user to define single ATCRBS or Mode S interrogations. 5.8.17.4.1.
Page 260 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.8.17.4.4. MODE S INTERROGATION MESSAGE DATA Command Syntax: {:ATC |:ATC5000NG}{:XPDR}{:UF}SP<numeric>CR Description: This command sets the data message for the Mode S Interrogation. Numeric: Short interrogation 0 to FFFFFFFFFFFFFF (14 hexadecimal ASCII) Long interrogation 0 to FFFFFFFFFFFFFFFFFFFFFFFFFFFF ( 28 hexadecimal ASCII).
Page 261 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.8.17.4.6. PULSE REPETITION FREQUENCY (PRF) Command Syntax: {:ATC |:ATC5000NG}{:XPDR}{:PRF }SP<numeric>CR Description: This command sets the pulse repetition rate (PRF). Numeric: 1 to 10000 (decimal ASCII) Default:...
Page 262 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.8.17.5.3. MODE REQUEST (CORRECTION) Command Syntax: {:ATC |:ATC5000NG}{:XPDR}{:MOD? |:MODE?} CR Description: This command replies with the current transponder interrogation mode. Note: Interrogation with CW reports the same as Single mode.
Page 263: Unit Commands
Set the Own Aircraft Mode S Address to 4. Reset Scenario. Set the ATC-5000NG to the factory default settings. Return Value: A”*” is returned if the factory settings are able to complete successfully or “?” if a failure occurs.
Page 264: Software Version Request
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.9.8. SOFTWARE VERSION REQUEST Command Syntax: {:ATC |:ATC5000NG}{:SW?}CR Description: This command returns the software version of the Unit. Return Value: ASCII value Example:...
Page 265: Dme Commands
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.10. DME COMMANDS 5.10.1. ACCELERATION Command Syntax: {:ATC |:ATC5000NG}{:DME}{:ACC | ACCELERATION} SP<numeric>CR Description: This command sets the acceleration parameter for range simulation. Numeric 0 to 399 ft/s/s (decimal ASCII) Default Value:...
Page 266: Echo Power
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.10.7. ECHO POWER Command Syntax: {:ATC |:ATC5000NG}{:DME:ECHO:POWER} SP<numeric>CR Description: This command sets the offset from the DME power for the echo pulses. Numeric +9 to -19 dBm (decimal ASCII) Default Value:...
Page 267: Ident Mode
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.10.13. IDENT MODE Command Syntax: {:ATC |:ATC5000NG}{:DME:IDENT:MODE} SP{TONE | CODE | OFF}CR Description: This command selects the mode of operation for DME identification. Default Value: Example: :ATC:DME:IDENT:MODE TONE\r...
Page 268: Pulse
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.10.20. PULSE Command Syntax: {:ATC |:ATC5000NG}{:DME:PULSE} SP{P1 | P2}CR Description: This command sets which pulse to measure. Default Value: Example: :ATC:DME:PULSE P1\r...
Page 269: Suppression
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.10.28. SUPPRESSION Command Syntax: {:ATC |:ATC5000NG}{:DME:}{SUPP | SUPPRESSION} SP{ON | OFF}CR Description: This command enables or disables the suppression output. Default Value: Example: :ATC:DME:SUPP ON\r...
Page 270: Examples
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.11. EXAMPLES 5.11.1. SCENARIO TEST The following example creates a scenario test with two static intruders and two dynamic intruders. //Begin Scenario Test Own Aircraft Definition Example : A T C : O W N : L A T 2 5 .
Page 271 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G Static Intruder Definition Example #2 : A T C : S C E : S T A T I C : 2 : M O D E T I S - B : A T C : S C E : S T A T I C : 2 : E N A B L E O N : A T C : S C E : S T A T I C : 2 : B E G I N 0 : A T C : S C E : S T A T I C : 2 : E N D 3 0 0 0...
Page 272: Test Single Ads-B Example
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G Dynamic Intruder Definition Example #2 / / D y n a m i c I n t r u d e r N u m b e r 2 : A T C : S C E : D Y N A M I C : 2 : M O D E T I S - B : A T C : S C E : D Y N A M I C : 2 : E N A B L E O N : A T C : S C E : D Y N A M I C : 2 : B E G I N 0...
Page 273: Test Dual Ads-B Example
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.11.3. DO-260 TEST DUAL ADS-B EXAMPLE The following example creates a test of type normal for a dual ADS-B. / / B E G I N T E S T / / R E S E T D O 2 6 0 T E S T : A T C : D O 2 6 0 : R E S E T...
Page 274: Special Test Bit Failures Example
:ATC:DO260:TYPE:BITFAILURES:CHIPS:FIRST 33 :ATC:DO260:TYPE:BITF:CHIPS:LAST 39 :ATC:DO260:TYPE:BITF:GENS:GENA:POWER -20 :ATC:DO260:TYPE:BITF:GENS:GENA:PATH TOP //:ATC:DO260:TYPE:BITF:GENS:GENA:DELAY 0 //No Available for Gen A. Bussines Rule's ATC-5000NG //:ATC:DO260:TYPE:BITF:GENS:GENA:SIGNAL ON //No Available for Special test. Bussines Rule's ATC-5000NG :ATC:DO260:TYPE:BITF:GENS:GENA:MODES:DATA 8800000148000000000000000001 //:ATC:DO260:TYPE:BITF:GENS:GENA:MODES:RANDOM OFF //No Available for Special test. Business Rule's ATC-...
Page 275: Special Test Altered Preamble Example
:ATC:DO260:TYPE:ALT:PULSE:P4:REFERENCE GENA :ATC:DO260:TYPE:ALT:PULSE:P4:ENABLE ON :ATC:DO260:TYPE:ALTEREDPREAMBLE:GENS:GENA:POWER -20 :ATC:DO260:TYPE:ALT:GENS:GENA:PATH TOP //:ATC:DO260:TYPE:ALT:GENS:GENA:DELAY 0 //No Available for Gen A. Bussines Rule's ATC-5000NG //:ATC:DO260:TYPE:ALT:GENS:GENA:SIGNAL ON //No Available for Special Test. Bussines Rule's ATC-5000NG :ATC:DO260:TYPE:ALT:GENS:GENA:MODES:DATA 8800000148000000000000000001 //:ATC:DO260:TYPE:ALT:GENS:GENA:MODES:RANDOM OFF //No Available for Special test. Bussines Rule's ATC-...
Page 276: Transponder Block Transmission Example
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.11.7. TRANSPONDER BLOCK TRANSMISSION EXAMPLE The following example creates a block transmission: //BEGIN TEST :ATC:SCE:TYPE XPDR //RESET BLOCK TRANSMISSION TEST :ATC:XPDR:RESET //BLOCK DEFINITION...
Page 277: Uat Scenario Definition Example
The following example creates a scenario test with two statics intruders and two dynamic intruders by the channels UAT RX1 and UAT RX2. This capability requires ATC-5000NG specific UAT hardware. / / B e g i n S c e n a r i o T e s t...
Page 278 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G : A T C : S C E : D Y N A M I C : 1 : U A T : A D S B : 3 : P L C O D E 3 : A T C : S C E : D Y N A M I C : 1 : U A T : A D S B : 3 : P L T S E E E E E E E : A T C : S C E : D Y N A M I C : 1 : U A T : A D S B : 4 : P L C O D E 6 : A T C : S C E : D Y N A M I C : 1 : U A T : A D S B : 4 : P L T S F F F F F...
Page 279: Example Program
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 5.11.9. EXAMPLE PROGRAM / / T h i s e xa m p l e p r o g r a m i s p r o v i d e d t o a l l o w y o u t o q u i c k l y g e t s t a r t e d c o m m u n i c a t i n g wi t h t h e / / u n i t .
Page 280 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G i f ( s t a t u s < 0 ) / / f a i l e d t o i n i t i a l i z e / / D i s p l a y e r r o r m e s s a g e F m t ( M e s s a g e , "...
Page 281 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G s t a t u s = A T C _ c l o s e ( A T C G e n 1 ) ; / / = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = / / = = = E N D M A I N F I L E = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = / / = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =...
Page 282 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G # d e f i n e O N # d e f i n e A T C G e n 1 # d e f i n e A T C G e n 2 t y p e d e f s t r u c t { V i I n t 3 2...
Page 283 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G # i n c l u d e " t e s t _ s y s . h " # d e f i n e W A I T T I M E 0 _ 0 1 0 .
Page 284 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G V i C h a r B u f f e r 8 [ 8 0 ] ; V i C h a r B u f f e r 9 [ 8 0 ] ;...
Page 285 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G / / P u r p o s e : T h i s f u n c t i o n i n i t i a l i z e s t h e A T C G e n s p e c i f i e d i n t h e " T y p e " i n p u t p a r a m e t e r t o a k n o w n s t a t e .
Page 286 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G e l s e i f ( s t r c m p ( " R S 2 3 2 " , A T C G e n D e v i c e [ ( A T C G e n - 1 ) ] . B u s ) = = 0 ) / / R S - 2 3 2 i f ( ( a t o i ( A T C G e n D e v i c e [ ( A T C G e n - 1 ) ] .
Page 287 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G / / S e t v a r i a b l e s o o t h e r d r i v e r c a l l s w o n ' t b a i l o u t A T C G e n C o n n e c t [ ( A T C G e n - 1 ) ] = O N ;...
Page 288 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G A T C _ s t a t u s = A T C _ s e s s i o n I n f o C l o s e ( A T C G e n S e s s i o n [ ( A T C G e n - 1 ) ] ) ; i f ( i n s t P t r ! = N U L L ) f r e e ( i n s t P t r ) ;...
Page 289 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G ( V i B u f )W r i t e B u f , b y t e s , V I _ N U L L ) ) < 0 ) / / L o g t h i s a s t h e l a s t c o m m a n d t r a n s m i s s i o n t i m e i f ( ( A T C _ s t a t u s = A T C _ n x t C m d L o g ( A T C G e n S e s s i o n [ ( A T C G e n - 1 ) ] , wa i t T o N xt C m d ) ) <...
Page 290 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G / / L o g t h i s a s t h e l a s t c o m m a n d t r a n s m i s s i o n t i m e i f ( ( A T C _ s t a t u s = A T C _ n xt C m d L o g ( A T C G e n S e s s i o n [ ( A T C G e n - 1 ) ] , wa i t T o N xt C m d ) ) <...
Page 291 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G / / c h e c k f o r d a t a i n b u f f e r i f ( i s _ b u f f e r _ o c c u p i e d [ d e v i c e ] ! = 0 ) s t r n c p y ( r e a d B u f f e r , s a v e d _ b u f f e r [ d e v i c e ] , n u m b e r B y t e s T o R e a d - 1 ) ;...
Page 292 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G i f ( r e a d B u f f e r [ i ] = = 0 x 3 d ) / / = E q u a l [ j ] = i ;...
Page 293 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G c a s e 9 : F m t ( B u f f e r 9 , " % s < % s [ i 0 w* ] " , c o m m a , t m p _ b u f f e r [ i n d e x ] ) ; b r e a k ;...
Page 294 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G s t r c p y ( B u f f e r 8 , t m p _ b u f f e r [ i n d e x ] ) ; b r e a k ;...
Page 295 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G i f ( ( A T C _ s t a t u s = v i S e t A t t r i b u t e ( i n s t r u m e n t H a n d l e , V I _ A T T R _ T M O _ V A L U E , T I M E _ O U T _ N O R M _ V A L ) ) <...
Page 296 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G t h e w a r n i n g V I _ W A R N _ N S U P _ R E S E T . / / = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = V i S t a t u s _ V I _ F U N C A T C _ r e s e t ( V i I n t 1 6 A T C G e n ) V i S t a t u s A T C _ s t a t u s = V I _ S U C C E S S ;...
Page 297 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G / / D 4 T r a n s m i t t e r Q u e u e N o t E m p t y ( D a t a a v a i l a b l e f o r G P I B r e a d ) , ( G P I B O n l y ) / / D 5 C o m m a n d C o m p l e t e / U n i t R e a d y r e t u r n A T C _ s t a t u s ;...
Page 298 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G e l s e i f ( F i n d P a t t e r n ( r e s o u r c e N a m e , 0 , - 1 , " A S R L " , 0 , 0 ) ! = - 1 ) / / - C o n f i g u r e V I S A F o r m a t t e d I / O - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - i f ( ( A T C _ s t a t u s = v i S e t A t t r i b u t e ( * i n s t H a n d l e , V I _ A T T R _ T M O _ V A L U E , T I M E _ O U T _ N O R M _ V A L ) ) <...
Page 299 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G / / - R e s e t i n s t r u m e n t - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - i f ( r e s e t D e v i c e ) i f ( I D Q u e r y ) D e l a y ( W A I T T I M E 0 _ 0 2 ) ;...
Page 300 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G r e t u r n V I _ S U C C E S S ; / / = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = / / F u n c t i o n : G e t s e s s i o n f r o m wa i t l i s t / / P u r p o s e : T h i s f u n c t i o n g e t s t h e r e s o u r c e n a m e f r o m t h e o p e n l i s t...
Page 301 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G b r e a k ; / / I n v a l i d S e s s i o n a b o r t i f ( i n d e x >...
Page 302 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G / / P u r p o s e : T h i s f u n c t i o n i s u s e d o n l y b y t h e A T C _ i n i t f u n c t i o n . W h e n a n e r r o r i s d e t e c t e d t h i s f u n c t i o n i s c a l l e d t o c l o s e t h e o p e n r e s o u r c e m a n a g e r a n d i n s t r u m e n t o b j e c t s e s s i o n s a n d t o s e t t h e i n s t H a n d l e t h a t i s r e t u r n e d f r o m A T C _ i n i t t o...
Page 303 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G T H I S P A G E I N TE N TI O N A L L Y L E F T B L A N K . 1 - 2 - 5 P a g e 1 5 4 S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 304: Section 3 - Specifications
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G SECTION 3 - SPECIFICATIONS N O T E : A 4 5 m i n u t e wa r m - u p p e r i o d i s r e q u i r e d f o r a l l s p e c i f i c a t i o n s . N O T E : S p e c i f i c a t i o n s a r e s u b j e c t t o c h a n g e wi t h o u t n o t i c e .
Page 305: Spectral Purity (Typical)
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.1.3. SPECTRAL PURITY (TYPICAL) H a r m o n i c s : < - 5 0 d B c S p u r i o u s : <...
Page 306 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G PULSE POSITION (CONT) Mo d e S I n t e r r o g a t i o n : 2 .
Page 307: Pulse Width
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.1.8. PULSE WIDTH ( S p e c i f i e d a c c u r a c i e s a p p l y t o p u l s e s o f wi d t h ≥ 0 . 2 u s . ) A TC R B S I n t e r r o g a t i o n : 0 .
Page 308: Pulse Amplitude
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.1.10. PULSE AMPLITUDE - 1 9 t o + 9 d B ( ± 0 . 5 d B ) A TC R B S I n t e r r o g a t i o n V a r i a t i o n ( a l l p u l s e s ) R e s o l u t i o n : 0 .
Page 309: Prf
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.1.13. PRF S i n g l e I n t e r r o g a t i o n : 1 t o 1 0 k H z R e s o l u t i o n : 1 H z...
Page 310: Dme Simulation
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.1.16. DME SIMULATION 1 0 0 µs ( ± 0 . 1 µs ) a f t e r I d e n t p u l s e p a i r E q u a l i zi n g P u l s e P a i r : 1 3 5 0 H z ( ±...
Page 311: Receiver
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.2. RECEIVER 3.2.1. VSWR < 1 . 4 ( 9 5 2 t o 1 2 2 3 MH z) 3.2.2.
Page 312 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G MEASUREMENT (CONT) P u l s e R i s e / F a l l Ti m e R e s o l u t i o n : 1 n s ±...
Page 313: Scope Trigger Output (Scope 1 And Scope 2)
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.2.7. SCOPE TRIGGER OUTPUT (SCOPE 1 AND SCOPE 2) 1 µs ( ± 0 . 5 µs ) W i d t h : XP D R P o s i t i o n : - 1 t o 6 0 0 µs ( ±...
Page 314: Compliance/Standards
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G 3.5. COMPLIANCE/STANDARDS Th e A TC - 5 0 0 0 N G h a s b e e n e va l u a t e d a n d m e e t s t h e r e q u i r e m e n t s o f t h e f o l l o wi n g : 3.5.1.
Page 315 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G TH I S P A G E I N TE N TI O N A L L Y L E F T B L A N K . 1 - 3 - 1 P a g e 1 2 S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 316: Section 4 - Shipping
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G SECTION 4 – SHIPPING SHIPPING TEST SETS 1.1. INFORMATION A e r o f l e x Te s t S e t s r e t u r n e d t o f a c t o r y f o r c a l i b r a t i o n , s e r vi c e o r r e p a i r m u s t b e r e p a c k a g e d a n d s h i p p e d a c c o r d i n g t o t h e f o l l o wi n g c o n d i t i o n s : 1.1.1.
Page 317 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G F i g u r e 1 R e p a c k i n g P r o c e d u r e 1 - 4 - 1 P a g e 2 S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 318: Section 5 - Storage
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G SECTION 5 – STORAGE STORING TEST SET P e r f o r m t h e f o l l o wi n g s t o r a g e p r e c a u t i o n s wh e n e v e r t h e Te s t S e t i s s t o r e d f o r e xt e n d e d p e r i o d s ( m o r e t h a n s i x m o n t h s ) : ...
Page 319 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G TH I S P A G E I N TE N TI O N A L L Y L E F T B L A N K . 1 - 5 - 1 P a g e 2 S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 320: Appendix A - Connector Pin-Out Tables
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G APPENDIX A – CONNECTOR PIN-OUT TABLES I/O CONNECTORS – FRONT PANEL C O N N E C T O R T Y P E I N P U T / O U T P U T L A N...
Page 321: I/O Connectors - Rear Panel
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G I/O CONNECTORS – REAR PANEL C O N N E C T O R T Y P E I N P U T / O U T P U T E XTE R N A L P U L S E B N C...
Page 322 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G E X T E R N AL P U L S E M O D U L AT I O N I / O C o n n e c t o r T E S T M O D E B N C # 1 B N C # 2...
Page 323: Ate Line Connector Pin-Out Table
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G ATE LINE CONNECTOR PIN-OUT TABLE P I N N O . S I G N AL N AM E P I N N O .
Page 324: Gpib Bus Connector Pin-Out Table
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G GPIB BUS CONNECTOR PIN-OUT TABLE P I N N O . S I G N AL N AM E D 1 0 1 D 1 0 2 D 1 0 3...
Page 325: Lan Connector Pin-Out Table
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G LAN CONNECTOR PIN-OUT TABLE P I N N O . S I G N AL N AM E R X+ N O T U S E D N O T U S E D...
Page 326: Usb (A) Connector Pin-Out Table
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G USB (A) CONNECTOR PIN-OUT TABLE P I N N O . S I G N AL N AM E V C C D A TA - D A TA +...
Page 327: Usb (B) Connector Pin-Out Table
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G USB (B) CONNECTOR PIN-OUT TABLE P I N N O . S I G N AL N AM E V B U S ( 5 V ) D A TA - D A TA +...
Page 328: Appendix B - Metric/British Imperial Conversion Table With Nautical Distance Conversions
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G APPENDIX B – METRIC/BRITISH IMPERIAL CONVERSION TABLE WITH NAUTICAL DISTANCE CONVERSIONS M U L T I P L Y M U L T I P L Y C O N V E R T : I N T O :...
Page 329 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G TH I S P A G E I N TE N TI O N A L L Y L E F T B L A N K . A P P E N D I X B P a g e 2 S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 330: Appendix C - Abbreviations
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G APPENDIX C – ABBREVIATIONS A m p e r e s E MC E l e c t r o m a g n e t i c C o m p a t i b i l i t y A l t e r n a t i n g C u r r e n t E X T E x t e r n a l...
Page 331 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G L A N L o c a l A r e a N e t w o r k S p e c t r u m A n a l y z e r L C D L i q u i d C r y s t a l D i s p l a y...
Page 332 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G W a t t W h i s p e r S h o u t X P D R T r a n s p o n d e r µA...
Page 333 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G T H I S P A G E I N T E N T I O N A L L Y L E F T B L A N K . A P P E N D I X C P a g e 4 S u b j e c t t o E x p o r t C o n t r o l , s e e C o v e r P a g e f o r d e t a i l s .
Page 334: Appendix D - Atc-5000Ng Compatibility Command Set
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G APPENDIX D - ATC-5000NG COMPATIBILITY COMMAND SET D.1. SDX COMPATIBILITY COMMAND SET NOTES: • Th e A TC - 5 0 0 0 N G r e t u r n s t h e " # " c h a r a c t e r i f t h e U n i t c a n n o t m a k e a m e a s u r e m e n t . Th e S D X r e t u r n s 0 i f i t c a n n o t m a k e a m e a s u r e m e n t .
Page 335 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S D X C o m m a n d S u p p o r t e d / N o t S u p p o r t e d C o m m e n t s AT C - 5 0 0 0 N G E q u i va l e n t ( o r S i m i l a r ) AT C R B S C o m m a n d s...
Page 336 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S D X C o m m a n d S u p p o r t e d / N o t S u p p o r t e d C o m m e n t s AT C - 5 0 0 0 N G E q u i va l e n t ( o r S i m i l a r ) : MO D E S : P R E P U L S E : P O S i t i o n...
Page 337 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S D X C o m m a n d S u p p o r t e d / N o t S u p p o r t e d C o m m e n t s AT C - 5 0 0 0 N G E q u i va l e n t ( o r S i m i l a r ) P u l s e C o m m a n d s...
Page 338 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S D X C o m m a n d S u p p o r t e d / N o t S u p p o r t e d C o m m e n t s AT C - 5 0 0 0 N G E q u i va l e n t ( o r S i m i l a r ) : G E N : TR I G g e r...
Page 339 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S D X C o m m a n d S u p p o r t e d / N o t S u p p o r t e d C o m m e n t s AT C - 5 0 0 0 N G E q u i va l e n t ( o r S i m i l a r ) : ME A S u r e : P R E P L Y: B O Tt o m : A TC R B S ?
Page 340 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S D X C o m m a n d S u p p o r t e d / N o t S u p p o r t e d C o m m e n t s AT C - 5 0 0 0 N G E q u i va l e n t ( o r S i m i l a r ) : ME A S u r e : A V G O N...
Page 341 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S D X C o m m a n d S u p p o r t e d / N o t S u p p o r t e d C o m m e n t s AT C - 5 0 0 0 N G E q u i va l e n t ( o r S i m i l a r ) : D ME : I D E N T: C O D E...
Page 342: Atc-1400A/S-1403D Compatibility Command Set
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G D.2. ATC-1400A/S-1403D COMPATIBILITY COMMAND SET NOTES: • D u e t o o p e r a t i o n a l d i f f e r e n c e s i n A TC- 1 4 0 0 A / S - 1 4 0 3 D L a n d t h e A TC - 5 0 0 0 0 N G u n i t s , t e s t s wr i t t e n f o r t h e A TC- 1 4 0 0 A / S - 1 4 0 3 D L m a y n o t r u n o n t h e A TC- 5 0 0 0 N G wi t h o u t c o d e m o d i f i c a t i o n . F o r b e s t r e s u l t s i t i s r e c o m m e n d e d t o r e wr i t e t h e t e s t s t o u s e A TC- 5 0 0 0 N G n a t i v e c o m m a n d s .
Page 343: Atc-1400A Compatibility Command Set
Partial See individual Axn commands below for more details. X10, Auxiliary Unit Instructions (n = 1 to 4) for the 1403 n is expected to be 3. The ATC-5000NG does not indicate improper F2 spacing. :ATC:XPDR:AREP? Get XPDR Code/Altitude For example: With code set to 7654 and F2 spacing wide by 120ns, received "...
Page 344 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G AT C - 1 4 0 0 A S U P P O R T E D C O M M E N T S AT C 5 0 0 0 N G E Q U I V AL E N T C O M M AN D D E S C R I P T I O N...
Page 345 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G AT C - 1 4 0 0 A S U P P O R T E D C O M M E N T S AT C 5 0 0 0 N G E Q U I V AL E N T C O M M AN D D E S C R I P T I O N...
Page 346: 1403Dl Compatibility Command Set
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G D.3. 1403DL COMPATIBILITY COMMAND SET D.3.1. AXN COMMANDS S-1403DL AX N C O M M AN D S S - 1 4 0 3 D L S U P P O R T E D C O M M E N T S AT C 5 0 0 0 N G E Q U I V AL E N T...
Page 347 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G AX N C O M M AN D S S - 1 4 0 3 D L S U P P O R T E D C O M M E N T S AT C 5 0 0 0 N G E Q U I V AL E N T...
Page 348: S-1403Dl Compatibility Command Set
O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G D.3.2. S-1403DL COMPATIBILITY COMMAND SET S - 1 4 0 3 D L C O M M AN D S U P P O R T E D C O M M E N T S AT C 5 0 0 0 N G E Q U I V AL E N T ( O R...
Page 349 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S - 1 4 0 3 D L C O M M AN D S U P P O R T E D C O M M E N T S AT C 5 0 0 0 N G E Q U I V AL E N T ( O R C O M M AN D D E S C R I P T I O N...
Page 350 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S - 1 4 0 3 D L C O M M AN D S U P P O R T E D C O M M E N T S AT C 5 0 0 0 N G E Q U I V AL E N T ( O R C O M M AN D D E S C R I P T I O N...
Page 351 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S - 1 4 0 3 D L C O M M AN D S U P P O R T E D C O M M E N T S AT C 5 0 0 0 N G E Q U I V AL E N T ( O R C O M M AN D D E S C R I P T I O N...
Page 352 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S - 1 4 0 3 D L C O M M AN D S U P P O R T E D C O M M E N T S AT C 5 0 0 0 N G E Q U I V AL E N T ( O R C O M M AN D D E S C R I P T I O N...
Page 353 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S - 1 4 0 3 D L C O M M AN D S U P P O R T E D C O M M E N T S AT C 5 0 0 0 N G E Q U I V AL E N T ( O R C O M M AN D D E S C R I P T I O N...
Page 354 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S - 1 4 0 3 D L C O M M AN D S U P P O R T E D C O M M E N T S AT C 5 0 0 0 N G E Q U I V AL E N T ( O R C O M M AN D D E S C R I P T I O N...
Page 355 O P E R A T I O N M A N U A L A T C - 5 0 0 0 N G S - 1 4 0 3 D L C O M M AN D S U P P O R T E D C O M M E N T S AT C 5 0 0 0 N G E Q U I V AL E N T ( O R C O M M AN D D E S C R I P T I O N...
Page 356 We reserve the right to make design changes without notice. Go to http://ats.aeroflex.com/contact/sales-distribution for Sales and Service contact information. EXPORT CONTROL WARNING: This document contains controlled technical data under the jurisdiction of the Export Administration Regulations (EAR), 15 CFR 730-774.

Aeroflex ATC-5000NG Operation Manual

English

Section 1 - Description

Section 2 - Operation

Unknown

Section 3 - Specifications

Section 4 - Shipping

Section 5 - Storage

Appendix A - Connector Pin-Out Tables

Appendix B - Metric/British Imperial Conversion Table with Nautical Distance Conversions

Appendix C - Abbreviations

Appendix D - Atc-5000Ng Compatibility Command Set

Quick Links

Chapters

Need help?

Questions and answers

Related Manuals for Aeroflex ATC-5000NG

Summary of Contents for Aeroflex ATC-5000NG

Table of Contents