Craftsman C459-52831 Operator's Manual page 5

OPERATION
1. Do not put hands or feet near rotating parts, in the auger/impeller housing
or chute assembly. Contact with the rotating parts can amputate hands
and feet.
2. The auger/impeller control lever is a safety device. Never bypass its
operation. Doing so makes the machine unsafe and may cause personal
injury.
3. The control levers must operate easily in both directions and automatically
return to the disengaged position when released.
4. Never operate with a missing or damaged chute assembly. Keep all safety
devices in place and working.
5. Never run an engine indoors or in a poorly ventilated area. Engine exhaust
contains carbon monoxide, an odorless and deadly gas.
6. Do not operate machine while under the influence of alcohol or drugs.
7. Muffler and engine become hot and can cause a burn. Do not touch.
8. Exercise extreme caution when operating on or crossing gravel surfaces.
Stay alert for hidden hazards or traffic.
9. Exercise caution when changing direction and while operating on slopes.
10. Plan your snow-throwing pattern to avoid discharge towards windows,
walls, cars etc. Thus, avoiding possible property damage or personal
injury caused by a ricochet.
11. Never direct discharge at children, bystanders and pets or allow anyone in
front of the machine.
12. Do not overload machine capacity by attempting to clear snow at too fast
of a rate.
13. Never operate this machine without good visibility or light. Always be sure
of your footing and keep a firm hold on the handles. Walk, never run.
14. Disengage power to the auger/impeller when transporting or not in use.
15. Never operate machine at high transport speeds on slippery surfaces.
Look down and behind and use care when backing up.
16. If the machine should start to vibrate abnormally, stop the engine,
disconnect the spark plug wire and ground it against the engine. Inspect
thoroughly for damage. Repair any damage before starting and operating.
17. Disengage all control levers and stop engine before you leave the operat-
ing position (behind the handles). Wait until the auger/impeller comes
to a complete stop before unclogging the chute assembly, making any
adjustments, or inspections.
18. Never put your hand in the discharge or collector openings. Always use
the clean-out tool provided to unclog the discharge opening. Do not unclog
chute assembly while engine is running. Shut off engine and remain
behind handles until all moving parts have stopped before unclogging.
19. Use only attachments and accessories approved by the manufacturer (e.g.
wheel weights, tire chains, cabs etc.).
20. When starting engine, pull cord slowly until resistance is felt, then pull
rapidly. Rapid retraction of starter cord (kickback) will pull hand and arm
toward engine faster than you can let go. Broken bones, fractures, bruises
or sprains could result.
21. If situations occur which are not covered in this manual, use care and
good judgment. Contact your Sears Service Center for assistance.
SAFETY INSTRUCTIONS
MAINTENANCE & STORAgE
1. Never tamper with safety devices. Check their proper operation regularly.
2. Before cleaning, repairing, or inspecting machine disengage all control
3. Check bolts and screws for proper tightness at frequent intervals to keep
4. Do not change the engine governor setting or over-speed the engine. The
5. Snow thrower shave plates and skid shoes are subject to wear and
6. Check controls periodically to verify they engage and disengage properly
7. Maintain or replace safety and instruction labels, as necessary.
8. Observe proper disposal laws and regulations for gas, oil, etc. to protect
9. Prior to storing, run machine a few minutes to clear snow from machine
10. Never store the machine or fuel container inside where there is an open
11. Always refer to the operator's manual for proper instructions on off-season
12. Check fuel line, tank, cap, and fittings frequently for cracks or leaks.
13. Do not crank engine with spark plug removed.
Do not modify engine
To avoid serious injury or death, do not modify engine in any way. Tampering
with the governor setting can lead to a runaway engine and cause it to operate
at unsafe speeds. Never tamper with factory setting of engine governor.
Notice regarding Emissions
Engines which are certified to comply with California and federal EPA emission
regulations for SORE (Small Off Road Equipment) are certified to operate on
regular unleaded gasoline, and may include the following emission control
systems: Engine Modification (EM) Oxidizing Catalyst (OC), Secondary Air
Injection (SAI) and Three Way Catalyst (TWC) if so equipped.
Average Useful Life
According to the Consumer Products Safety Commission (CPSC) and the U.S.
Environmental Protection Agency (EPA), this product has an Average Useful
Life of seven (7) years, or 60 hours of operation. At the end of the Average
Useful Life, have the machine inspected annually by an authorized service
dealer to ensure that all mechanical and safety systems are working properly
and not worn excessively. Failure to do so can result in accidents, injuries or
death.
5
Refer to the maintenance and adjustment sections of this manual.
levers and stop the engine. Wait until the auger/impeller come to a
complete stop. Disconnect the spark plug wire and ground against the
engine to prevent unintended starting.
the machine in safe working condition. Also, visually inspect machine for
any damage.
governor controls the maximum safe operating speed of the engine.
damage. For your safety protection, frequently check all components and
replace with original equipment manufacturer's (OEM) parts only. "Use of
parts which do not meet the original equipment specifications may lead to
improper performance and compromise safety!"
and adjust, if necessary. Refer to the adjustment section in this operator's
manual for instructions.
the environment.
and prevent freeze up of auger/impeller.
flame, spark or pilot light such as a water heater, furnace, clothes dryer
etc.
storage.
Replace if necessary.