Advertisement
Quick Links
Advertisement
Summary of Contents for IDTECK UOM
- Page 1 User Manual OUTPUT EXPANSION MODULE...
-
Page 2: Table Of Contents
User Manual Table of Contents 1. SAFETY INFORMATION ..............3 2. PRODUCTION INTRODUCTION ............5 3. UOM CONFIGURATION ..............6 4. PREPARATION FOR INSTALLATION ............8 5. INSTALLATION ................. 9 6. COMMUNICATION WIRING ..............12 7. BOARD STATUS LED DESCRIPTION ........... 12... -
Page 3: Safety Information
User Manual 1. Safety Information To prevent safety accident and property damage, read through information below and use the product properly. This symbol indicates that dangerous voltage consisting risk of electric shock present within this unit This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. - Page 4 User Manual Caution - Usage - Do not drop objects on the product or apply strong blows to it. . - Keep away from magnetic interference. - Keep out of direct sunlight and heat radiation sources. - If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall - Do not locate the device near combustible substance such as spray.
-
Page 5: Production Introduction
Enables device to run with ESD-resistance design which has an antistatic feature. Also protects device from noise so system runs with stability. 2.2 Contents Please find below contests of UOM package. UOM comes with followings UOM 1ea Quick Installation Guide 2.3 Specification... -
Page 6: Uom Configuration
User Manual 3. UOM configuration 3.1 UOM Board (Figure: UIM board configuration) - Page 7 Board ID LED Shows board ID RESET S/W Reboot UOM. Setting values remains after the reboot. Initializes all the values of UIM to factory default and resets Initialization Switch UIM. Press this switch for more than 3 seconds to initialize...
-
Page 8: Preparation For Installation
User Manual 4. Preparation for installation 4.1 1 Installation diagram for RS485 communication Each iFDC/iEDC set can be expanded to max. 4 sets of UOM (Figure: installation diagram with RS485 communication) -
Page 9: Installation
User Manual 5. Installation 5.1 Port description for wiring 5.1.1 UOM board port (Figure: UOM Board) Name ① Power port ② RS485 communication port ③ Relay output(#1 ~ #16) port ④ input(#1 ~ #2) port ⑤ Board ID setting switch... - Page 10 1. Set each UOM board ID to install. 2. Proceed with wiring 2-1 Connect UOM fixing holes to either NEMA case or Earth GND and proceed with ground connection. 2-2 wire power. 2-3 wire input devices.
- Page 11 User Manual Caution – Board ID setting Board ID shouldn’t be duplicated as it is unique address for communication. If same board ID exists, there can be communication error. 5.4 Power wiring - Connect +12V cable (red) to +12 V power port of UIM board. -Connect GND cable (black) of DC 12V power supply to GND port of UIM board.
-
Page 12: Communication Wiring
(Figure: RS485 Communication with multiple connections) 7. Board status LED description 7.1 UOM board status LED description For LED configuration, please refer to ‘Figure: UOM board configuration’ above. When UOM is working properly, each LED lights up as below description LD #1 Shows power status. -
Page 13: How To Make Rma Request (After Sales Service)
Please refer to the IDTECK webpage for more details. RMA Code will be issued after the RMA Center reviews the RMA request form. Enclose the product along with the RMA Code and send it to IDTECK RMA Center. (Product without RMA Code is not accepted.) If you have any questions or problems regarding the RMA services, please contact us using the contac t information below. - Page 14 The specifications contained in this manual are subject to change without notice at any time. 5F, Ace Techno Tower B/D, 468, Gangseo-ro, Gangseo-Gu, Seoul, 157-721, Korea Tel : +82-2-2659-0055 Fax : +82-2-2659-0086 E-mail : webmaster@idteck.com September. 2015 Copyright © IDTECK Co., Ltd.