1. Manuals
  2. Brands
  3. Acuity Controls Manuals
  4. Enclosure
  5. nLight ECLYPSE
  6. Safety instructions

Acuity Controls nLight ECLYPSE Safety Instructions

Hide thumbs Also See for nLight ECLYPSE:
1
2
3
4
5

Advertisement

Table of Contents

nLight ECLYPSE Enclosure
SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION
!
All servicing should be performed by qualified service personnel.
!
When using electrical equipment, basic safety precautions should always be followed including the
following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
Do not use outdoors.
Do not mount near gas or electric heaters.
Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by
unauthorized personnel.
The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
Do not use this equipment for other than intended use.
SAVE THESE INSTRUCTIONS.
!
Remove internal assembly prior to drilling/punching additional or larger holes for conduits, and
remove excess metal shavings and contaminants prior to powering the panel
Acuity Controls assumes no responsibility for claims arising out of improper or careless installation or handling of this product. Failure to follow any of
Always read complete installation instructions prior to installation!
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com © 2017 Acuity Brands Lighting, Inc. All rights reserved. 06/21/17
912-00023-001
READ AND FOLLOW ALL SAFETY INSTRUCTIONS!

IMPORTANT SAFETY INSTRUCTIONS

these instructions could void product warranty.
For a complete listing of product Terms and Conditions, please visit www.AcuityControls.com
SAVE THESE INSTRUCTIONS
Page 1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the nLight ECLYPSE and is the answer not in the manual?

Questions and answers

Related Manuals for Acuity Controls nLight ECLYPSE

Summary of Contents for Acuity Controls nLight ECLYPSE

  • Page 1: Important Safety Instructions

    Acuity Controls assumes no responsibility for claims arising out of improper or careless installation or handling of this product. Failure to follow any of these instructions could void product warranty.
  • Page 2 ECLYPSE Enclosure ENCLOSURE MOUNTING INSTRUCTIONS SURFACE MOUNT ENCLOSURE WITH SCREW COVER TO REMOVE RELAY PANEL COVER: 1) UNFASTEN FOUR PHILLIPS SCREWS AT CORNERS OF COVER 2) REMOVE COVER FROM RIGHT EDGE AND ENGAGEMENT FEATURES ON LEFT SIDE WILL RELEASE...
  • Page 3 ECLYPSE Enclosure SURFACE MOUNT ENCLOSURE MOUNTING AND KNOCKOUT DIMENSIONS 8-RELAY SIZED PANEL SHOWN, BUT APPLIES TO 16-RELAY VERSION Box Dimensions & Installation Application Notes 14 1/4" 1 5/16" 2 1/8" 10" TYP 4" 1 1/8" 12" 1 1/8" 3/4"...
  • Page 4 ECLYPSE Enclosure BOX DIMENSIONS & INSTALLATION APPLICATION NOTES The NECY enclosure was designed with minimal knockouts to provide installers the freedom to add additional conduit feeds to better meet specific site conditions without locking them into confined positions or preset trade size fittings.
  • Page 5 ECLYPSE Enclosure nLIGHT ECLYPSE WIRING DIAGRAM Knockout Knockout (High Voltage) USB 1 USB 2 nLight Port 1 nLight Port 2 DIN Rail DIN Clip nLight Port 3 (Supports Ethernet Secondary Modbus GFX module) RS-485 Ethernet Primary Knockout Knockout Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com © 2017 Acuity Brands Lighting, Inc. All rights reserved. 06/21/17...

Table of Contents