Advertisement
Quick Links
Light Source
User Guide
MicroLED
Light Source Range
Models covered by this manual:
UFO MICSL DMX
Please read this manual fully before installing, operating or performing
maintenance on the light source unit.
Universal Fibre Optics
Home Place | Coldstream | TD12 4DT | United Kingdom
Tel: +44 (0)1890 883416 | Fax: +44 (0)1890 883062
www.fibreopticlighting.com
Issue 4 | Revised: 260418
Advertisement
Summary of Contents for Universal Fibre Optics MICSL DMX
- Page 1 User Guide MicroLED Light Source Range Models covered by this manual: UFO MICSL DMX Please read this manual fully before installing, operating or performing maintenance on the light source unit. Universal Fibre Optics Home Place | Coldstream | TD12 4DT | United Kingdom Tel: +44 (0)1890 883416 | Fax: +44 (0)1890 883062 www.fibreopticlighting.com...
- Page 2 INTRODUCTION Thank you for purchasing this UFO Light source. Please read these instructions fully before connecting your unit to the electrical supply, and keep them for future reference. The UFO MicroLED range of light sources utilises an RGBW LED array and is suitable for use with either glass or polymer fibre-optic harness This MicroLED is powered by a 100-240VAC PSU or LED Driver.
- Page 3 This luminaire is powered by a 12V Power Supply Unit or 12V Constant Voltage Driver. Remove the PSU/driver from its box. The driver caters for UK/European/other mains supplies using the relevant power cord supplied. Connect the jack plug into the socket in the back, and the light source is now ready for connection Universal Fibre Optics...
- Page 4 MOUNTING If using the metal mounting plate proceed as follows: STEP 1 Remove the rubber feet from the bottom of the Light Source STEP 2 Push fit three of the expansion fittings into the holes vacated by the feet as shown – DO NOT fit an expansion fitting into the foot hole at the rear below the push buttons STEP 3 Place the mounting plate on the base as shown and push the remaining expansion...
-
Page 5: Stand-Alone Operation
Push once Push once Push once 1 (white start) 2 (red start) Push once Push once Push once At any time the cycle can be stopped on a colour and started again using the Lower push button. Universal Fibre Optics... -
Page 6: Dmx Operation
DMX OPERATION To use the Slave in DMX operation connect a DMX Cat5 cable between one of the RJ45 sockets at the rear of the Slave Light Source and the DMX Controller- see RJ45 connection details and drawing below: Pin no. White White White... - Page 7 Brilliant Blue (B06) Bright Blue (B28) Congo (B93) Violet (V43) Magenta (M56) Pink (M63) White Please note that Canary (bright yellow) is difficult to achieve using the composite colours, and as such is a poor match. Figure 1 Universal Fibre Optics...
- Page 8 Problem Probable cause(s) Remedy Mains supply off Check supply and reinstate Unit is dead - LED power Loose mains plugs Check plugs indicator is not illuminated PSU failed Replace PSU LED array failure Replace Light Source Unit is dead - no light output but LED power indicator is still May have been switched off...
-
Page 9: Technical Specifications
(L)137mm x(W) 114mm x (H)73mm MAINTENANCE Please note that a record of all maintenance MUST be kept in the table below, indicating what maintenance was undertaken and when. This MUST be dated for warranty purposes. Date Maintenance Undertaken Universal Fibre Optics... - Page 10 NOTES MicroLED Light Source Range...
- Page 11 NOTES Universal Fibre Optics...
- Page 12 Universal Fibre Optics Home Place | Coldstream | TD12 4DT | United Kingdom Tel: +44 (0)1890 883416 | Fax: +44 (0)1890 883062 www.fibreopticlighting.com...