Table of Contents
Advertisement
Quick Links
F3.20 High Pressure Paddlewheel Flow Sensor
INSTRUCTION MANUAL
Table of Contents
1. Introduction........................................................................... 2
1.1. Safety Instructions.............................................................................2
1.2. Unpacking........................................................................................ 2
2. Description............................................................................. 2
2.1. Design.............................................................................................. 2
2.2. Operating Principle............................................................................. 3
2.3. Connection to FlowX3 Instruments...................................................... 3
3. Specifications........................................................................ 3
3.1. Technical Data.................................................................................. 3
4. Installation............................................................................. 4
4.1. Location........................................................................................... 4
4.2. Mounting Position............................................................................. 5
4.3. Process Connection.......................................................................... 5
4.4. Wiring.............................................................................................. 6
5. Installation Fittings................................................................. 7
6. K-Factor Tables...................................................................... 7
7. Ordering Data........................................................................ 8
8. Weld-on Adapters installation procedure ................................... 9
1
F3.20 Paddlewheel Flow Sensor
EN 12-02
Advertisement
Table of Contents
Related Manuals for FLS FlowX3 series
Summary of Contents for FLS FlowX3 series
-
Page 1: Table Of Contents
F3.20 High Pressure Paddlewheel Flow Sensor INSTRUCTION MANUAL EN 12-02 Table of Contents 1. Introduction………………………………………………………………… 2 1.1. Safety Instructions……………………………………………………..……………2 1.2. Unpacking……………………………………………………………………….…… 2 2. Description…………………………………………………….……………. 2 2.1. Design…………………………………………………………………..…………….. 2 2.2. Operating Principle………………………………………………………………..3 2.3. Connection to FlowX3 Instruments……………………………………………... 3 3. Specifications……………………………………………………………… 3 3.1. -
Page 2: Introduction
1. Introduction 1.1. Safety Instructions General Statements The sensor F3.20.X.XX has only been designed to measure the flow of liquids. Do not install and service the sensor without following the Instruction Manual. This sensor is designed to be connected to other instruments which can be ... -
Page 3: Operating Principle
2.2. Operating Principle The flow sensor consists of a transducer and a five-blade open cell paddlewheel using insertion technology. The paddlewheel is equipped with a permanent magnet integrated into each blade. As the magnet passes close to the transducer a pulse is generated. -
Page 4: Installation
Specific for F3.20.H Supply voltage: 5 to 24 VDC regulated Supply current: < 30 mA @ 24 VDC Output signal: square wave Output frequency: 45 Hz per m/s nominal (13.7 Hz per ft/s nominal) Output type: transistor NPN open collector Output current: 10 mA max. -
Page 5: Mounting Position
4.2. Mounting Position Make sure the pipeline is always full. Horizontal pipe runs: Fig. 1: installation with no sediments present Fig. 2: installation with no air bubbles present Fig. 3: installation if sediments or air bubbles may be present Vertical pipe runs: ... -
Page 6: Wiring
N.B. The slot milling of the weld on adapter must be parallel to the flow. The arrow on the sensor must be close to the milling weld on adapter. 4.4. Wiring Always ensure the power supply is switched off before working on the sensor. ... -
Page 7: Installation Fittings
5. Installation Fittings Type Description Size: DN 40 to DN 200 ( 1 ½” to 8” ) 316L SS Weld-on Adapters 6. K-Factor Tables K-Factor is the number of pulses a sensor produces for one liter of fluid measured. Here all K-Factors for water at ambient temperature are listed. -
Page 8: Ordering Data
7. Ordering Data FlowX3 F3.00.H.XX (Remote version) Part No. Version Power supply Length Body Enclosure F3.20.H.01 Hall 5 - 24 VDC INOX IP68 F3.20.P.01 Push-Pull 12 - 24 VDC INOX IP68 Spare Parts Item Part No. Description F3.SP4.3 ECTFE (Halar) rotor with Inox Shaft F3.SP8 flat gasket + screws F3.20 Paddlewheel Flow Sensor... -
Page 9: Weld-On Adapters Installation Procedure
8. Weld-on Adapters installation procedure Calculate the length A and mark it on the adapter. Measure the adapter diameter at the mark level and drill the hole in the pipe with such diameter. Insert the adapter into the pipe and to be sure that the milling slot is parallel to the flow (see drawing n°2) ... - Page 10 F3.20 Paddlewheel Flow Sensor...
- Page 11 F3.20 Paddlewheel Flow Sensor...
- Page 12 F.I.P. Formatura Iniezione Polimeri S.p.A. Loc. Pian di Parata, 16015 Casella (GE) – Italy Tel +39 010 96211 – Fax +39 010 9621209 www.flsnet.it F3.20 Paddlewheel Flow Sensor...