Advertisement
Quick Links
Caution:
• Read all instructions before assembling or using Sled Wheels. Follow the steps in order.
•
Only use Sled Wheels as intended, following all instructions contained herein for assembly and adjustment.
•
Do not exceed 12 miles per hour when driving a snowmobile with Sled Wheels.
•
The handle is a lever used to raise the skis by pushing down on it; do not lift the handle while Sled Wheels are
engaged on ski. Lift the ski loop instead, if necessary.
•
Relieve the load on the latch before releasing it by pushing the handle and ski to the ground.
•
Always use the safety pin to lock the latch in place.
•
Remove Sled Wheels from the ski when not in use.
Tools needed: Torx T-55 wrench, 5/32" Hex wrench (supplied), #2 Phillips screwdriver, ¼" or larger flat blade
screwdriver
Assembly time: about 20 minutes
Parts list:
Item
Description
1
Wheel
2
Axle bolt
3
Washer, ½"
4
Nut, ½-13
Saddle/Latch
5
assembly
6
Arm, Left
7
Arm, Right
8
Hex Wrench, 5/32
Telescoping
9
Handle
10
T-Handle
BHCS, Hex, 1/4-
11
20 x 1.5"
BHCS, Hex, 1/4-
12
20 x 0.5"
- Page 1 -
Caliber Sled Wheels Assembly
Instructions for PN 13576 and 13579
QTY
4
4
4
4
2
2
2
1
2
2
2
2
Item
Description
BHCS, Hex, 1/4-20 x
13
1.0"
14
Nut, Square, 1/4-20
15
Washer, ¼"
16
Cover, Finger, Right
17
Cover, Finger, Left
Extender, Finger,
18
Right
19
Extender, Finger, Left
Screw, Thread
20
Forming, #8-16
Safety Pin w/ lanyard
21
and Caution Card
22
Grease, 1cc
23
Vibratite, 1cc
QTY
8
12
10
2
2
1
1
4
2
1
1
CI05067, rev B
Advertisement
Related Manuals for Caliber 13576
Summary of Contents for Caliber 13576
- Page 1 Caliber Sled Wheels Assembly Instructions for PN 13576 and 13579 Caution: • Read all instructions before assembling or using Sled Wheels. Follow the steps in order. • Only use Sled Wheels as intended, following all instructions contained herein for assembly and adjustment.
- Page 2 Assembly: 1. Cut the Vibratite packet (23) and empty into a disposable container. Paint the last five threads of all the bolts in the kit (11, 12, and 13), including the axles (2). Wait ten minutes for the Vibratite to dry before proceeding with screws.
- Page 3 4. Apply one fourth of the grease (22) to each axle (2) and assemble a wheel (1), ½” washer (3), arm (6 and 7), and hex nut (4). Tighten the axle until snug, then tighten the axle 1/4 - 1/2 turn more with a T-55 Torx wrench.
- Page 4 6. Slide the Saddle/Latch assemblies (5) over the Telescoping Handles (9) with the latch side first. Slip a ¼” square nut (14) into the Telescoping Handle T-slot, and secure with a ¼-20 x 1.5” screw (11), and a safety pin/lanyard assembly (21), using the lanyard loop as a washer.
- Page 5 Adjustment: Key adjustments 1. If not done previously, adjust the width of each Sled Wheel assembly to be approximately ½” wider than the ski. Include space to avoid the spindle screw if it sticks out past the ski. Tighten, but do not over tighten the arm clamp screws.
- Page 6 2. Position one Sled Wheel assembly above the ski so that the Sled Wheels axle is directly above the ski spindle axle. Loosen the Telescoping handle screw and move the handle so it hits the end of the ski. Tighten the screw. 3.
- Page 7 5. Grab one Sled Wheel assembly by the handle, hold it vertically, and slide the fingers under the ski until the wheel axle is in line with the spindle axle. You may need to lift the ski loop to create space under the ski. Rotate the assembly down to raise the ski and check the length of the telescoping handle.
- Page 8 CALIBER, INC. LIMITED LIFETIME WARRANTY Caliber, Inc. warrants that this product will be free from defects in material or workmanship under normal use, installation and service. Caliber, Inc. reserves the right, before having any obligation under this limited warranty, to inspect the damaged Caliber product. All warranty shipping costs for inspection shall be borne solely by the purchaser. This limited warranty is non-transferable.