On The Vcr Display - Sanyo VHR-630 Instruction Manual

Jj
—.. -,
L
MENWTV -1 {I , ,
-- G-CODE
:::'2:
-–-o-9
CH+, ---I,-, ~; _–.. oK
CLEAR –-
13
i
G-CODE TIMER
RECORDINGPROGRAMMING
——
Programming on the VCR display
You
can programme or confirm a G-Code
timer recording on the VCR display even if
the TV is turned off.
1
Press the G-CODE button.
9 bars (-) will appear on the display,
If 6 timer recordings have already been
set, the 9 bars (-) are not displayed.
Please refer to "Confirmation" and
"Canceling" on page 15.
z Using the numeric buttons, enter the
Code number for the programme yo!~
want to record,
&amp/e: Enter the Code number 489135
If you entered a wrong number, press the
CLEAR button to delete it, then enter the
correct number,
3
Press the
OK
button.
The programmed recording programme
position number ;]rrd recording on tirnc
are displayed.
Notes,
If the programme position number (Pf'1) displays
$1--1':
f?nter the programrrm position number the l-V
station has been prmx?t 10,
TIwl sc[ting will be
mcrn
)rizerf ancl s[![ the I IC:xt
time the same TV sl:tlion is :;clected.
a When alltheseNinqs areas desired,
press the OK button.
You can programme another recording by
repeating steps 2 to 4.
5 Insert a videocassette with
erasure-prevention tab,
Make sure the tape is longer than the total
recording time.
6
Press the G-CODE button.
The timer indicator (P_J) w ill light on the
VCR display and the VCR goes into timer
recording stand-by mode.
Additional settings
After pressing
the OK button in step 3.
Daily/Weekly recording
Press the MENU/TV button repeatedly to
select:
"M-F": for daily recording (Monday through
Friday)
"WK": for weekly recording (the same
programme every week)
No display: for one time recording
Note:
Daily recording starting on a Saturday or Sunday
will not be possible.
Changing the off time
Each press of the (CH+ or CH-) button will
change the recording off time by units of 10
minutes,
—
Vew Zealand only
Vote on sky decoders and recording
B
There arc at present two types of sky
decoders available in New Zealand.
1.
\
> ..
—
Base Band Decoder
(no remote control
supplied, older type).
You cannot successfully record G-Code
programmed using this type of decoder,
(Unless your video is modified internally first.)
Contact Sky TV for details.
IRD
Decoder
(supplied with Sky Remote and
with UHF output),
This decoder allows you to programme
recordings using the G-Code function. You
can use the Sky CODE NUMBERS to record
Sky TV programmed with your
VCR,
However,
please note the following limitations,
(a) The Sky CODE NUMBERS used
with the
VCR can not change the channels on Ihc
Sky Decoder.
This means you must first preselect the
Sky channel you want to record (movies,
sport, news)
(b)
The VCR will then turn on and record [1IP
progrnmrnc posilio! I WIlich lIas been S(II
for Sky. (e.g. progrornrrw position "4")
The Sky chamml you record (rnowcs,
sport, news) will depend on which
channel the decoder was left on.
(c) Remember the first lime you use a Sky
CODE NUMBER, the programme position
number
("PR")
on the video needs to be
set the same for all three Sky channels.
This will depend on the programme
position number you allocated for Sky in the
set up. ie programme position number "4",
;,, .