Table of Contents
Advertisement
2
PREPARATION
!!
(!)/1
PRESET
CH(+, -)
RF converter output
(Video channel)
Area
1
Factov
1
Range
settina
The RF
converter of this
VCR
has been factory set to
Australian UHF37.
The New Zealand and
Australian channels are not tht
same,
This means UHF37
Aus
is basically the same as UHF36
NZ, But not exactly the same.
~
2
~~~
VIDEOCHANNEL SETTING
If the VCR has
been connected
to the TV
using tha "AV connection", simply set your TV to
the "AV" mode. Go to _
VCR TUNING.
1
2
3
Turn cm your TV and set your TV to
"VCR" or the position designated for VCR
use (always a position where no TV
programme
is received).
Turn off the VCR using the 0/1 button.
Press the PRESET button on the remote
control for more than 3 seconds.
The VCR display shows the RF OutDut
channel.
4
Tune the UHF channel on the TV to the
displayed RF output channel 37.
For New Zealand', tune the UHF channel 36.
The test pattern (below) will appear.
5
This completes the video channel setting.
Adjust the tuning on the TV, if necessary,
so that the test pattern is clear
If the test pattern
is disturbed
or
replaced
by a
TV station, go to step 6.
If the test pattern stays the same, press
the
PRESET
button.
The VCR is turned off.
PREPARATION
I
I
IT
WI
CH (+,-)
CHANNkL (-,+)
II
I
I
6
7
8
Change the RF output channel number on
the VCR display to a vacant channel
number applicable to your area.
For Australia:
Press the CH (+) button.
137RFA~
,s
38 RF A -------------------
+ 69 RF A
'----------------------------
-
29 RFAe
28RF
Press the CH (-) button to return to
channel "28 RF.
For New
Zealand:
Press the CH (-) button.
137 RFA~
1=
28 RF 1--]+
---- +69 RF n
&
'-------------------------
+
22 RFn-21RFn
Press the CH (+) button to return to
channel "28 RF'.
Tune the UHF channel on the TV to the
changed RF output channel.
The test pattern will be appear.
Adjust the tuning on the TV, if necessary,
so that the test pattern is clear.
If the test pattern stays the same, press
Fr@VCR
TUNING
the PRES"ET button .-
The VCR is turned off.
This completes
the video channel
setting.
Turn on the VCR using the 0/1 button.
For Australia - Tuning confirmation
The TV stations are preset as follows.
Programme
,,2,,
,,7,,
Dosition
I
"9"
I ",~,!
I
"28"
TVstation
(MHz)
64.25 182.25 196.25 209.25 527.25
To keep the preset channel tuning, press the
CH (+
or -) button.
To modify the channel tuning, follow the steps
below.
For New Zealand
(and Australia,
if
necessary)
Press the
CHANNEL (+
and -) buttons on the
VCR for 3 seconds or more.
Auto tuning will start.
Auto tuning
This VCR has a built-in tuner capable of
tuning up to 44 TV stations.
The TV stations available in your area will be
automatically
preset in order starting from
program me position number "01".
Notes:
During the auto tuning operations,
please
do not press any of the buttons or controls
on the VCR or remote control.
Auto tuning is not possible if the VCR is set
to external input mode.
The skip function will be automatically
set
for all position numbers where no TV
station has been preset.
When the Auto tuning is finished, the TV
station preset to the lowest programme
position number will be tuned on your TV
screen.
Press the CH (+ or -) button to confirm that the
channels tuning has been performed.
7
Advertisement
Table of Contents
